LinuxMCE - User contributions [en]

Onkyo TXSR805

2009-07-06T19:30:00Z

Blackhat:

[[category: Audio]]
{{stub}}
[[category: Tutorials]]
== Using the Onkyo TX-SR805 with RS232 Control ==

'''THIS CODE IS STILL BEING DEVELOPED'''

Future home of the howto for setting up a Onkyo TX-SR805 with RS232 support.
 
May widen howto to all Onkyo RS232 Receivers.
 

This device does currently work with limited functionality. A writeup for how to add this device to a Linux MCE system will be done soon. 
 
** If you use this device and have any problems or suggestions to the code here, please switch over to the discussion tab and bring it to my attention ** 

----
 
Current features supported: 
-On/Off 
-Change inputs 
-Volume control (Up/Down in set increments. cmd_313 Set Volume still needs work) 
 
Being worked on: 
-Precise Volume Control (cmd_313) 
-Listening Modes 
-Zone 2/3 
-FM Tuner 
 
----
'''Ruby Code:'''

Section: 193 Off 
<$"!1PWR00\r"$>

Section: 192 On 
<$"!1PWR01\r"$>
sleep(2)
<$"!AMT00\r"$>
@mute = false

Section: 169 AM 
<$"!1SLI25\r"$>

Section: 164 Aux 
<$"!1SLI03\r"$>

Section: 172 Aux 2 
<$"!1SLI04\r"$>

Section: 162 CD 
<$"!1SLI23\r"$>

Section: 165 DVD 
<$"!1SLI10\r"$>

Section: 170 FM 
<$"!1SLI24\r"$>

Section: 163 Phono 
<$"!1SLI22\r"$>

Section: 160 Tape / Tape 1 
<$"!1SLI20\r"$>

Section: 173 Tape 2 
<$"!1SLI21\r"$>

Section: 166 Tuner 
<$"!1SLI26\r"$>

Section: 909 XM 
<$"!1SLI31\r"$>

Section: 373 Private Method Listing 
# Written by Jason Bennett
#
# Process 373 - Methods
def receiveMsg
buff = conn_.Recv(7, 1000)
log("Message Received: #{buff}")
trash = conn_.Recv(1, 100)
if (buff.length() < 7)
parsed1 = "ERR"
parsed2 = "00"
else
parsed2 = buff[5].chr + buff[6].chr
parsed1 = buff[2].chr + buff[3].chr + buff[4].chr
return [parsed1, parsed2]
end
end
#-------------------------------------------- Parsing -----------------------------------------------------------------------------------
def chkMsg(cat, opt)
case cat
# Power
when "PWR"
cmd = Command.new(device_.devid_, -1001, 1, 2, 48) # 48 = Power State
case opt
when "01"
cmd.params_[10] = "1" # Command 48, Param 10: 1 = On
when "00"
cmd.params_[10] = "0" # Command 48, Param 10: 2 = Off
end
SendCommand(cmd)
# Master Volume Level
when "MVL"
cmd = Command.new(device_.devid_, -1001, 1, 2, 71) # 71 = Volume
cmd.params_[30] = opt.hex.to_s # Command 71, Param 16 = Volume Level in Decimal
log("volume reported as: #{opt.hex.to_s}")
SendCommand(cmd)
# Input Selection
when "SLI"
cmd = Command.new(device_.devid_, -1001, 1, 2, 49) # 49 = Input Selection
case opt
when "00"
input_param = 316
when "01"
input_param = 317
when "02"
input_param = 318
when "03"
input_param = 164
when "04"
input_param = 172
when "10"
input_param = 165
when "20"
input_param = 160
when "22"
input_param = 163
when "23"
input_param = 162
when "24"
input_param = 170
when "25"
input_param = 169
when "26"
input_param = 166
when "31"
input_param = 909
end
cmd.params_[41] = input_param.to_s() # Command 49, Param 41 = Input
SendCommand(cmd)
end
end
#-------------------------------------------- Logging -----------------------------------------------------------------------------------
def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end

Section: 350 Process Incoming Data 
# Written by Jason Bennett
#
# Process 350 - Incoming
incMsg = receiveMsg()
log("New Msg: #{incMsg[0]}:#{incMsg[1]}")
chkMsg(incMsg[0], incMsg[1])

Section: 355 Process Initialize 
#31-May-06 14:13 init Onkyo Receiver
initok=false
for iRetry in 0...4
print "Initializing unit\n"
conn_.Send("!1PWRQSTN\r")
buf = conn_.Recv(200, 1000)
if( !buf.nil? && !buf.index("PWR0").nil? )
print "Initialized ok\n"
initok=true
break
else
print "Didn't respond to command\n"
end
end
if initok==false
DisableDevice( device_.devid_, true )
print "The device wouldn't respond. Disabling it.\n"
return
end
print "Initialized ok, doing log\n"

Section: 97 Mute 
if(@mute)
<$"!1AMT00\r"$>
else
<$"!1AMT01\r"$>
end
@mute=!@mute

Section: 313 Set Volume 
slevel = sprintf( "%x", level.to_i)
<$"!1MVL" + slevel + "\r"$>
SetDeviceDataInDB( device_.devid_, 158, level ) # 158 = DEVICEDATA_Volume_Level_CONST
print "volume and corresponding device data set\n"

Section: 90 Vol Down 
<$"!1MVLDOWN\r"$>

Section: 89 Vol Up 
<$"!1MVLUP\r"$>

Mitsubishi HC1500

2008-06-23T05:23:29Z

Blackhat:

[[Category: Tutorials]]
[[Category: GSD]]
[[category:video]]
[[category: Hardware]]
{{stub}}
== Controlling a Mitsubishi HC1500 Projector with RS232 ==

Future home of HC1500 howto

----
'''Ruby Code'''

Section: 193 Off 
log("Sending Off Command")
<$"00\x22\x0D"$>
sleep(2)
<$"00\x22\x0D"$>

Section: 192 On 
log("Sending On Command")
<$"00\x21\x0D"$>
sleep(2)
<$"00\x21\x0D"$>

Section: 373 Prive Method Listing 
#Written by Jason Bennett
def testMsg(msg)
cmd = Command.new(device_.devid_, -1001, 1, 2, 48)
if (msg =~ /00\x21/)
cmd.params_[10] = "1" #Device Turned on
log("Telling DCE Projector is on")
end
if (msg =~ /00\x22/)
cmd.params_[10] = "0" #Device Turned off
log("Telling DCE Projector is off")
end
SendCommand(cmd)
end
def recvMsg()
reply = String.new
while (true)
buff = conn_.Recv(1, -1)
if (buff.length() == 0)
break
end
reply = reply + buff[-1].chr
end
log("New Message: #{reply}")
return reply
end
def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end

Section: 350 Process Incoming Data 
#Written by Jason Bennett
msg = recvMsg()
testMsg(msg)
log("Message Caught: #{msg}")

Section: 355 Process Initialize 
<$"00\x21\x0D"$>

Receivers rs-232

2008-06-23T05:19:21Z

Blackhat: /* Onkyo */

[[Category: Hardware]]
[[Category: Serial]]
[[Category: Audio]]

= Receivers rs-232 support =
Here is a list of receivers that do or do not have rs-232 (serial port) support

== Denon ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| AVR-2307
|
|
|
|-
| AVR-2308
|
|
|
|-
| AVR-2807
|
|
|
|-
| AVR-2808
|
|
|
|-
| AVR-3807
| yes
| yes
|
|-
| [[Denon_AVR-4306|AVR-4306]]
| no (ethernet)
| yes (ethernet)
| Seemed to work fine at LinuxTag 2008, although no extensive testing was done.
|}

== Harman Kardon ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| AVR 247
| yes
| no
|
|-
| AVR 347
|
|
|
|}

== Marantz ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| SR5001
|
|
|
|-
| SR5002
|
|
|
|-
| [http://www.marantz.com/new/index.cfm?fuseaction=Products.Product&cont=eu&bus=hf&prod_id=3662&series=comp&type=avr SR6001 ]
|
|
|
|-
| SR5600
| yes
| yes
| in development(several problems exist)
|-
| SR7001
| yes
| yes
|
|-
| [http://www.marantz.com/new/index.cfm?fuseaction=Products.Product&cont=eu&bus=hf&prod_id=3702&series=comp&type=avr SR7002]
|
|
|
|-
| ZR6001
|
|
|
|}

== Meridian ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| [http://www.meridian-audio.com/p_g68.htm G68-ADV]
| yes
| yes
|
|}

== NAD ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| T-765
|
|
|
|-
| T-773
|
|
|
|}

== Onkyo ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| TX-SR705
|
|
|
|-
| TX-SR805/875
| yes
| yes
| [[Onkyo_TXSR805]]
|}

== Pioneer ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| VSX-LX60
|
|
|
|-
| VSX-LX70
|
|
|
|}

== Sony ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| STR-DA3000ES
|
|
|
|-
| STR-DA3200ES
|
|
|
|}

== Yamaha ==
{| class="wikitable" border="1" cellpadding="5" cellspacing="0"
|-
! model
! rs-232 port
! rs-232 controllable
! lmce support
|-
| RX-V1700
|
|
|
|-
| RX-V1800
|
|
|
|-
| RX-V2700
|
|
|
|}

Onkyo TXSR805

2008-06-23T05:09:29Z

Blackhat:

[[category: Audio]]
{{stub}}
[[category: Tutorials]]
== Using the Onkyo TX-SR805 with RS232 Control ==

'''THIS CODE IS STILL BEING DEVELOPED'''

Future home of the howto for setting up a Onkyo TX-SR805 with RS232 support.
 
May widen howto to all Onkyo RS232 Receivers.
 

This device does currently work with limited functionality. A writeup for how to add this device to a Linux MCE system will be done soon.

----
 
Current features supported: 
-On/Off 
-Change inputs 
-Volume control (Up/Down in set increments. cmd_313 Set Volume still needs work) 
 
Being worked on: 
-Precise Volume Control (cmd_313) 
-Listening Modes 
-Zone 2/3 
-FM Tuner 
 
----
'''Ruby Code:'''

Section: 193 Off 
<$"!1PWR00\r"$>

Section: 192 On 
<$"!1PWR01\r"$>
sleep(2)
<$"!AMT00\r"$>
@mute = false

Section: 169 AM 
<$"!1SLI25\r"$>

Section: 164 Aux 
<$"!1SLI03\r"$>

Section: 172 Aux 2 
<$"!1SLI04\r"$>

Section: 162 CD 
<$"!1SLI23\r"$>

Section: 165 DVD 
<$"!1SLI10\r"$>

Section: 170 FM 
<$"!1SLI24\r"$>

Section: 163 Phono 
<$"!1SLI22\r"$>

Section: 160 Tape / Tape 1 
<$"!1SLI20\r"$>

Section: 173 Tape 2 
<$"!1SLI21\r"$>

Section: 166 Tuner 
<$"!1SLI26\r"$>

Section: 909 XM 
<$"!1SLI31\r"$>

Section: 373 Private Method Listing 
# Written by Jason Bennett
#
# Process 373 - Methods
def receiveMsg
buff = conn_.Recv(7, 1000)
log("Message Received: #{buff}")
trash = conn_.Recv(1, 100)
if (buff.length() < 7)
parsed1 = "ERR"
parsed2 = "00"
else
parsed2 = buff[5].chr + buff[6].chr
parsed1 = buff[2].chr + buff[3].chr + buff[4].chr
return [parsed1, parsed2]
end
end
#-------------------------------------------- Parsing -----------------------------------------------------------------------------------
def chkMsg(cat, opt)
case cat
# Power
when "PWR"
cmd = Command.new(device_.devid_, -1001, 1, 2, 48) # 48 = Power State
case opt
when "01"
cmd.params_[10] = "1" # Command 48, Param 10: 1 = On
when "00"
cmd.params_[10] = "0" # Command 48, Param 10: 2 = Off
end
SendCommand(cmd)
# Master Volume Level
when "MVL"
cmd = Command.new(device_.devid_, -1001, 1, 2, 71) # 71 = Volume
cmd.params_[30] = opt.hex.to_s # Command 71, Param 16 = Volume Level in Decimal
log("volume reported as: #{opt.hex.to_s}")
SendCommand(cmd)
# Input Selection
when "SLI"
cmd = Command.new(device_.devid_, -1001, 1, 2, 49) # 49 = Input Selection
case opt
when "00"
input_param = 316
when "01"
input_param = 317
when "02"
input_param = 318
when "03"
input_param = 164
when "04"
input_param = 172
when "10"
input_param = 165
when "20"
input_param = 160
when "22"
input_param = 163
when "23"
input_param = 162
when "24"
input_param = 170
when "25"
input_param = 169
when "26"
input_param = 166
when "31"
input_param = 909
end
cmd.params_[41] = input_param.to_s() # Command 49, Param 41 = Input
SendCommand(cmd)
end
end
#-------------------------------------------- Logging -----------------------------------------------------------------------------------
def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end

Section: 350 Process Incoming Data 
# Written by Jason Bennett
#
# Process 350 - Incoming
incMsg = receiveMsg()
log("New Msg: #{incMsg[0]}:#{incMsg[1]}")
chkMsg(incMsg[0], incMsg[1])

Section: 355 Process Initialize 
#31-May-06 14:13 init Onkyo Receiver
initok=false
for iRetry in 0...4
print "Initializing unit\n"
conn_.Send("!1PWRQSTN\r")
buf = conn_.Recv(200, 1000)
if( !buf.nil? && !buf.index("PWR0").nil? )
print "Initialized ok\n"
initok=true
break
else
print "Didn't respond to command\n"
end
end
if initok==false
DisableDevice( device_.devid_, true )
print "The device wouldn't respond. Disabling it.\n"
return
end
print "Initialized ok, doing log\n"

Section: 97 Mute 
if(@mute)
<$"!1AMT00\r"$>
else
<$"!1AMT01\r"$>
end
@mute=!@mute

Section: 313 Set Volume 
slevel = sprintf( "%x", level.to_i)
<$"!1MVL" + slevel + "\r"$>
SetDeviceDataInDB( device_.devid_, 158, level ) # 158 = DEVICEDATA_Volume_Level_CONST
print "volume and corresponding device data set\n"

Section: 90 Vol Down 
<$"!1MVLDOWN\r"$>

Section: 89 Vol Up 
<$"!1MVLUP\r"$>

Onkyo TXSR805

2008-06-23T05:07:20Z

Blackhat:

[[category: Audio]]
{{stub}}
[[category: Tutorials]]
== Using the Onkyo TX-SR805 with RS232 Control ==

'''THIS CODE IS STILL BEING DEVELOPED'''

Future home of the howto for setting up a Onkyo TX-SR805 with RS232 support.

May widen howto to all Onkyo RS232 Receivers.

----
 
Current features supported: 
-On/Off 
-Change inputs 
-Volume control (Up/Down in set increments. cmd_313 Set Volume still needs work) 
 
Being worked on: 
-Precise Volume Control (cmd_313) 
-Listening Modes 
-Zone 2/3 
-FM Tuner 
 
----
'''Ruby Code:'''

Section: 193 Off 
<$"!1PWR00\r"$>

Section: 192 On 
<$"!1PWR01\r"$>
sleep(2)
<$"!AMT00\r"$>
@mute = false

Section: 169 AM 
<$"!1SLI25\r"$>

Section: 164 Aux 
<$"!1SLI03\r"$>

Section: 172 Aux 2 
<$"!1SLI04\r"$>

Section: 162 CD 
<$"!1SLI23\r"$>

Section: 165 DVD 
<$"!1SLI10\r"$>

Section: 170 FM 
<$"!1SLI24\r"$>

Section: 163 Phono 
<$"!1SLI22\r"$>

Section: 160 Tape / Tape 1 
<$"!1SLI20\r"$>

Section: 173 Tape 2 
<$"!1SLI21\r"$>

Section: 166 Tuner 
<$"!1SLI26\r"$>

Section: 909 XM 
<$"!1SLI31\r"$>

Section: 373 Private Method Listing 
# Written by Jason Bennett
#
# Process 373 - Methods
def receiveMsg
buff = conn_.Recv(7, 1000)
log("Message Received: #{buff}")
trash = conn_.Recv(1, 100)
if (buff.length() < 7)
parsed1 = "ERR"
parsed2 = "00"
else
parsed2 = buff[5].chr + buff[6].chr
parsed1 = buff[2].chr + buff[3].chr + buff[4].chr
return [parsed1, parsed2]
end
end
#-------------------------------------------- Parsing -----------------------------------------------------------------------------------
def chkMsg(cat, opt)
case cat
# Power
when "PWR"
cmd = Command.new(device_.devid_, -1001, 1, 2, 48) # 48 = Power State
case opt
when "01"
cmd.params_[10] = "1" # Command 48, Param 10: 1 = On
when "00"
cmd.params_[10] = "0" # Command 48, Param 10: 2 = Off
end
SendCommand(cmd)
# Master Volume Level
when "MVL"
cmd = Command.new(device_.devid_, -1001, 1, 2, 71) # 71 = Volume
cmd.params_[30] = opt.hex.to_s # Command 71, Param 16 = Volume Level in Decimal
log("volume reported as: #{opt.hex.to_s}")
SendCommand(cmd)
# Input Selection
when "SLI"
cmd = Command.new(device_.devid_, -1001, 1, 2, 49) # 49 = Input Selection
case opt
when "00"
input_param = 316
when "01"
input_param = 317
when "02"
input_param = 318
when "03"
input_param = 164
when "04"
input_param = 172
when "10"
input_param = 165
when "20"
input_param = 160
when "22"
input_param = 163
when "23"
input_param = 162
when "24"
input_param = 170
when "25"
input_param = 169
when "26"
input_param = 166
when "31"
input_param = 909
end
cmd.params_[41] = input_param.to_s() # Command 49, Param 41 = Input
SendCommand(cmd)
end
end
#-------------------------------------------- Logging -----------------------------------------------------------------------------------
def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end

Section: 350 Process Incoming Data 
# Written by Jason Bennett
#
# Process 350 - Incoming
incMsg = receiveMsg()
log("New Msg: #{incMsg[0]}:#{incMsg[1]}")
chkMsg(incMsg[0], incMsg[1])

Section: 355 Process Initialize 
#31-May-06 14:13 init Onkyo Receiver
initok=false
for iRetry in 0...4
print "Initializing unit\n"
conn_.Send("!1PWRQSTN\r")
buf = conn_.Recv(200, 1000)
if( !buf.nil? && !buf.index("PWR0").nil? )
print "Initialized ok\n"
initok=true
break
else
print "Didn't respond to command\n"
end
end
if initok==false
DisableDevice( device_.devid_, true )
print "The device wouldn't respond. Disabling it.\n"
return
end
print "Initialized ok, doing log\n"

Section: 97 Mute 
if(@mute)
<$"!1AMT00\r"$>
else
<$"!1AMT01\r"$>
end
@mute=!@mute

Section: 313 Set Volume 
slevel = sprintf( "%x", level.to_i)
<$"!1MVL" + slevel + "\r"$>
SetDeviceDataInDB( device_.devid_, 158, level ) # 158 = DEVICEDATA_Volume_Level_CONST
print "volume and corresponding device data set\n"

Section: 90 Vol Down 
<$"!1MVLDOWN\r"$>

Section: 89 Vol Up 
<$"!1MVLUP\r"$>

Onkyo TXSR805

2008-06-23T05:06:33Z

Blackhat:

[[category: Audio]]
{{stub}}
[[category: Tutorials]]
== Using the Onkyo TX-SR805 with RS232 Control ==

'''THIS CODE IS STILL BEING DEVELOPED'''

Future home of the howto for setting up a Onkyo TX-SR805 with RS232 support.

May widen howto to all Onkyo RS232 Receivers.

----

Current features supported:
-On/Off
-Change inputs
-Volume control (Up/Down in set increments. cmd_313 Set Volume still needs work)

Being worked on:
-Precise Volume Control (cmd_313)
-Listening Modes
-Zone 2/3
-FM Tuner

----
'''Ruby Code:'''

Section: 193 Off 
<$"!1PWR00\r"$>

Section: 192 On 
<$"!1PWR01\r"$>
sleep(2)
<$"!AMT00\r"$>
@mute = false

Section: 169 AM 
<$"!1SLI25\r"$>

Section: 164 Aux 
<$"!1SLI03\r"$>

Section: 172 Aux 2 
<$"!1SLI04\r"$>

Section: 162 CD 
<$"!1SLI23\r"$>

Section: 165 DVD 
<$"!1SLI10\r"$>

Section: 170 FM 
<$"!1SLI24\r"$>

Section: 163 Phono 
<$"!1SLI22\r"$>

Section: 160 Tape / Tape 1 
<$"!1SLI20\r"$>

Section: 173 Tape 2 
<$"!1SLI21\r"$>

Section: 166 Tuner 
<$"!1SLI26\r"$>

Section: 909 XM 
<$"!1SLI31\r"$>

Section: 373 Private Method Listing 
# Written by Jason Bennett
#
# Process 373 - Methods
def receiveMsg
buff = conn_.Recv(7, 1000)
log("Message Received: #{buff}")
trash = conn_.Recv(1, 100)
if (buff.length() < 7)
parsed1 = "ERR"
parsed2 = "00"
else
parsed2 = buff[5].chr + buff[6].chr
parsed1 = buff[2].chr + buff[3].chr + buff[4].chr
return [parsed1, parsed2]
end
end
#-------------------------------------------- Parsing -----------------------------------------------------------------------------------
def chkMsg(cat, opt)
case cat
# Power
when "PWR"
cmd = Command.new(device_.devid_, -1001, 1, 2, 48) # 48 = Power State
case opt
when "01"
cmd.params_[10] = "1" # Command 48, Param 10: 1 = On
when "00"
cmd.params_[10] = "0" # Command 48, Param 10: 2 = Off
end
SendCommand(cmd)
# Master Volume Level
when "MVL"
cmd = Command.new(device_.devid_, -1001, 1, 2, 71) # 71 = Volume
cmd.params_[30] = opt.hex.to_s # Command 71, Param 16 = Volume Level in Decimal
log("volume reported as: #{opt.hex.to_s}")
SendCommand(cmd)
# Input Selection
when "SLI"
cmd = Command.new(device_.devid_, -1001, 1, 2, 49) # 49 = Input Selection
case opt
when "00"
input_param = 316
when "01"
input_param = 317
when "02"
input_param = 318
when "03"
input_param = 164
when "04"
input_param = 172
when "10"
input_param = 165
when "20"
input_param = 160
when "22"
input_param = 163
when "23"
input_param = 162
when "24"
input_param = 170
when "25"
input_param = 169
when "26"
input_param = 166
when "31"
input_param = 909
end
cmd.params_[41] = input_param.to_s() # Command 49, Param 41 = Input
SendCommand(cmd)
end
end
#-------------------------------------------- Logging -----------------------------------------------------------------------------------
def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end

Section: 350 Process Incoming Data 
# Written by Jason Bennett
#
# Process 350 - Incoming
incMsg = receiveMsg()
log("New Msg: #{incMsg[0]}:#{incMsg[1]}")
chkMsg(incMsg[0], incMsg[1])

Section: 355 Process Initialize 
#31-May-06 14:13 init Onkyo Receiver
initok=false
for iRetry in 0...4
print "Initializing unit\n"
conn_.Send("!1PWRQSTN\r")
buf = conn_.Recv(200, 1000)
if( !buf.nil? && !buf.index("PWR0").nil? )
print "Initialized ok\n"
initok=true
break
else
print "Didn't respond to command\n"
end
end
if initok==false
DisableDevice( device_.devid_, true )
print "The device wouldn't respond. Disabling it.\n"
return
end
print "Initialized ok, doing log\n"

Section: 97 Mute 
if(@mute)
<$"!1AMT00\r"$>
else
<$"!1AMT01\r"$>
end
@mute=!@mute

Section: 313 Set Volume 
slevel = sprintf( "%x", level.to_i)
<$"!1MVL" + slevel + "\r"$>
SetDeviceDataInDB( device_.devid_, 158, level ) # 158 = DEVICEDATA_Volume_Level_CONST
print "volume and corresponding device data set\n"

Section: 90 Vol Down 
<$"!1MVLDOWN\r"$>

Section: 89 Vol Up 
<$"!1MVLUP\r"$>