LinuxMCE - User contributions [en]

ATI Radeon-X800-AGP

2008-01-21T20:15:24Z

Matd:

[[Category: Hardware]]
[[Category: Video]]
[[Category: Graphic Cards]]

[[Image:ATI-X800-XL-AGP-F.jpg|thumb|ATI X800 XL Front]]
[[Image:ATI-X800-XL-AGP-B.jpg|thumb|ATI X800 XL Back]]

'''Ati Radeon X800 AGP'''

My model is X800 XL VIVO AGP with 256MB DDR3. It has 1xDVI, 1xVGA and 1xS-Video connector.

P/N 102A4900500000001

[http://support.ati.com/ics/support/default.asp?deptID=894&task=knowledge&folderID=7518&questionID=1385 Ati website] says that the card is built by ATI or built by a partner company using ATI components.

Additional power connector must be used, without it you don`t get 3D acceleration.

Card came to me only with power cable.

Works with Standard UI1 and UI2 with Overlay using fglrx driver version Catalyst 7.12 (8.44.3).

For smooth video enable video overlay in your device section in xorg.conf (my config below).

Section "Device"
Identifier "ATI Technologies Inc R430 [Radeon X800]"
Driver "fglrx"
BusID "PCI:1:0:0"
Option "UseInternalAGPGART" "off"
Option "OpenGLOverlay" "off"
Option "VideoOverlay" "on"
Option "EnableMonitor" "tmds1,none"
EndSection

Also add

Section "ServerFlags"
Option "AIGLX" "off"
EndSection

Section "Extensions"
Option "Composite" "Disable"
EndSection

without this you can encouter display problems.

If you managed to configure your card properly, kernel module is loaded and you choose UI2 in AVWizard then you will see something like...

[[Image:UI2-ATI-Radeon-X800.jpg]]

*[http://ati.amd.com/products/radeonx800/index.html Radeon X800 on Ati website]

ATI Radeon-X800-AGP

2008-01-08T10:55:39Z

Matd:

[[Category: Hardware]]
[[Category: Video]]
[[Category: Graphic Cards]]

[[Image:ATI-X800-XL-AGP-F.jpg|thumb|ATI X800 XL Front]]
[[Image:ATI-X800-XL-AGP-B.jpg|thumb|ATI X800 XL Back]]

'''Ati Radeon X800 AGP'''

My model is X800 XL VIVO AGP with 256MB DDR3. It has 1xDVI, 1xVGA and 1xS-Video connector.

P/N 102A4900500000001

[https://support.ati.com/ics/support/KBAnswer.asp?questionID=1385 Ati website] says that the card is built by ATI or built by a partner company using ATI components.

Additional power connector must be used, without it you don`t get 3D acceleration.

Card came to me only with power cable.

Works with Standard UI1 and UI2 with Overlay using fglrx driver version Catalyst 7.12 (8.44.3).

For smooth video enable video overlay in your device section in xorg.conf (my config below).

Section "Device"
Identifier "ATI Technologies Inc R430 [Radeon X800]"
Driver "fglrx"
BusID "PCI:1:0:0"
Option "UseInternalAGPGART" "off"
Option "OpenGLOverlay" "off"
Option "VideoOverlay" "on"
Option "EnableMonitor" "tmds1,none"
EndSection

Also add

Section "ServerFlags"
Option "AIGLX" "off"
EndSection

Section "Extensions"
Option "Composite" "Disable"
EndSection

without this you can encouter display problems.

If you managed to configure your card properly, kernel module is loaded and you choose UI2 in AVWizard then you will see something like...

[[Image:UI2-ATI-Radeon-X800.jpg]]

*[http://ati.amd.com/products/radeonx800/index.html Radeon X800 on Ati website]

ATI Radeon-X800-AGP

2008-01-07T22:10:14Z

Matd:

[[Category: Hardware]]
[[Category: Video]]
[[Category: Graphic Cards]]

[[Image:ATI-X800-XL-AGP-F.jpg|thumb|ATI X800 XL Front]]
[[Image:ATI-X800-XL-AGP-B.jpg|thumb|ATI X800 XL Back]]

'''Ati Radeon X800 AGP'''

My model is X800 XL VIVO AGP with 256MB DDR3. It has 1xDVI, 1xVGA and 1xS-Video connector.

Additional power connector must be used, without it you don`t get 3D acceleration.

Card is OEM and came to me only with power cable.

Works with Standard UI1 and UI2 with Overlay using fglrx driver version Catalyst 7.12 (8.44.3).

For smooth video enable video overlay in your device section in xorg.conf (my config below).

Section "Device"
Identifier "ATI Technologies Inc R430 [Radeon X800]"
Driver "fglrx"
BusID "PCI:1:0:0"
Option "UseInternalAGPGART" "off"
Option "OpenGLOverlay" "off"
Option "VideoOverlay" "on"
Option "EnableMonitor" "tmds1,none"
EndSection

Also add

Section "ServerFlags"
Option "AIGLX" "off"
EndSection

Section "Extensions"
Option "Composite" "Disable"
EndSection

without this you can encouter display problems.

If you managed to configure your card properly, kernel module is loaded and you choose UI2 in AVWizard then you will see something like...

[[Image:UI2-ATI-Radeon-X800.jpg]]

*[http://ati.amd.com/products/radeonx800/index.html Radeon X800 on Ati website]

File:UI2-ATI-Radeon-X800.jpg

2008-01-07T22:10:10Z

Matd:

Medion-MD1-NBC-lirc.conf

2008-01-07T21:50:02Z

Matd:

<pre>
# brand: Medion MD1 NBC (Made in China X10)
# Medion Digitainer Remote Control
# model no. of remote control:
# * P/N: 20018268
# * FCC ID: B4S20018268
# devices being controlled by this remote: LinuxMCE
#

begin remote
name lircd.conf
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
pre_data_bits 8
pre_data 0x14
post_data_bits 16
post_data 0x0
gap 219967
toggle_bit_mask 0x80800000

begin codes
1 0xE20D
2 0x638E
3 0xE40F
4 0x6590
5 0xE611
6 0x6792
7 0xE813
8 0x6994
9 0xEA15
0 0x6C97
Play 0xFA25
Pause 0x7EA9
Stop 0xFD28
Record 0x7CA7
SkipNext 0xF823
SkipPrior 0x76A1
Forward 0xFB26
Rewind 0x79A4
snapshot 0xED18
red 0x87B2
yellow 0x0934
blue 0x8AB5
green 0x0833
Mute 0x5580
return 0xF11C
VolUp 0x5E89
VolDown 0xDD08
ChanUp 0x608B
ChanDown 0xE10C
menu 0x6E99
back 0xF520
Left 0x729D
Right 0xF41F
Up 0xCDF8
Down 0x4570
tv 0x81AC
Videos 0x022D
DVD 0x5984
Guide 0xEB16
Music 0x5B86
Radio 0x032E
book 0x86B1
Pictures 0xDA05
info 0x84AF
Power 0xD702
ok 0x709B
enter 0xF31E
end codes

end remote
</pre>

Medion MD1 NBC

2008-01-07T21:41:58Z

Matd:

[[Category: Hardware]]
[[Category: Input]]
[[Category: Supported]]
===Medion MD1 NBC===
[[Image:Medion-MD1-NBC.jpg|Medion MD1 NBC RF Remote Control]]

Medion MD1 NBC (Made in China by X10) is a RF Remote Controler.

It has all (almost) what you need to control your LinuxMCE.
It uses 2 x 1.5V AAA batteries.
*P/N: 20018268
*FCC ID: B4S20018268

I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.

===X10 Receiver===
The X10 RF receiver need to be connected directly into the mainboard USB pin.

*P/N: 20018267

Technical Specification:

It has CE mark so it is approved for use in the EU.
*RF Frequency: 433 MHz
*Operating range: 30m or 60feet (open field)
*Can support up to 16 remotes
*Works through walls using RF technology even when not aimed at the receiver

===Setup===
The device works with LMCE using LIRC. I`ve configured my device using [[Add_support_for_new_remote_controls]] guide.

'''Note:'''LinuxMCE will automatically load '''ati_remote''' kernel module which doesn`t seem to work.
You need to prevent doing this by either doing

<code>
echo "blacklist ati_remote" >>/etc/modprobe.d/blacklist<br>
</code>
as root or deleting the module.

My [[Medion-MD1-NBC-lirc.conf|lircd.conf]].

Medion MD1 NBC

2008-01-07T21:17:41Z

Matd:

[[Category: Hardware]]
[[Category: Input]]
[[Category: Supported]]

[[Image:Medion-MD1-NBC.jpg|thumb|200px|Medion MD1 NBC RF Remote Control]]
===Medion MD1 NBC===
Medion MD1 NBC (Made in China by X10) is a RF Remote Controler.

It has all (almost) what you need to control your LinuxMCE.
It uses 2 x 1.5V AAA batteries.
*P/N: 20018268
*FCC ID: B4S20018268

I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.

===X10 Receiver===
The X10 RF receiver need to be connected directly into the mainboard USB pin.

*P/N: 20018267

Technical Specification:
It has CE mark so it is approved for use in the EU.
*RF Frequency: 433 MHz
*Operating range: 30m or 60feet (open field)
*Can support up to 16 remotes
*Works through walls using RF technology even when not aimed at the receiver

===Setup===
The device works with LMCE using LIRC. I`ve configured my device using [[Add_support_for_new_remote_controls]] guide.

'''Note:'''LinuxMCE will automatically load '''ati_remote''' kernel module which doesn`t seem to work.
You need to prevent doing this by either doing

<code>
echo "blacklist ati_remote" >>/etc/modprobe.d/blacklist<br>
</code>
as root or deleting the module.

File:Medion-MD1-NBC.jpg

2008-01-07T20:47:10Z

Matd:

Medion MD1 NBC

2008-01-07T20:46:32Z

Matd:

[[Category: Hardware]]
[[Category: Input]]
[[Category: Supported]]

[[Image:Medion-MD1-NBC.jpg|thumb|200px|Medion MD1 NBC RF Remote Control]]

Medion MD1 NBC (Made in China by X10) is a RF Remote Controler, I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.
==X-10 Receiver==
The X-10 RF receiver need to be connected directly into the mainboard USB pin.

This is an European version it works in
RF Frequency: 433 MHz

The device works with LMCE using LIRC. I`ve configured my device using [[Add_support_for_new_remote_controls]] guide.

ATI Radeon-X800-AGP

2008-01-07T19:55:14Z

Matd:

[[Category: Hardware]]
[[Category: Video]]
[[Category: Graphic Cards]]

[[Image:ATI-X800-XL-AGP-F.jpg|thumb|ATI X800 XL Front]]
[[Image:ATI-X800-XL-AGP-B.jpg|thumb|ATI X800 XL Back]]

'''Ati Radeon X800 AGP'''

My model is X800 XL VIVO AGP with 256MB DDR3. It has 1xDVI, 1xVGA and 1xS-Video connector.

Additional power connector must be used, without it you don`t get 3D acceleration.

Card is OEM and came to me only with power cable.

Works with Standard UI1 and UI2 with Overlay using fglrx driver version Catalyst 7.12 (8.44.3).

For smooth video enable video overlay in your device section in xorg.conf (my config below).

Section "Device"
Identifier "ATI Technologies Inc R430 [Radeon X800]"
Driver "fglrx"
BusID "PCI:1:0:0"
Option "UseInternalAGPGART" "off"
Option "OpenGLOverlay" "off"
Option "VideoOverlay" "on"
Option "EnableMonitor" "tmds1,none"
EndSection

Also add

Section "ServerFlags"
Option "AIGLX" "off"
EndSection

Section "Extensions"
Option "Composite" "Disable"
EndSection

without this you can encouter display problems.

*[http://ati.amd.com/products/radeonx800/index.html Radeon X800 on Ati website]

ATI Radeon-X800-AGP

2008-01-07T19:23:11Z

Matd:

File:ATI-X800-XL-AGP-B.jpg

2008-01-07T19:09:09Z

Matd:

File:ATI-X800-XL-AGP-F.jpg

2008-01-07T19:08:38Z

Matd:

ATI Radeon-X800-AGP

2008-01-07T18:23:17Z

Matd:

ATI Radeon-X800-AGP

2008-01-07T18:18:49Z

Matd:

[[Category: Hardware]]
[[Category: Video]]
[[Category: Graphic Cards]]

'''Ati Radeon X800 AGP'''
My model is X800 XL VIVO AGP with 256MB DDR2. It has 1xDVI, 1xVGA and 1xS-Video connector.
Additional power connector must be used, without it you don`t get 3D acceleration.
Card is OEM and came to me only with power cable.

Works with Standard UI1 and UI2 with Overlay using fglrx driver.