Apex Destiny-6100 - Revision history

Zaerc at 15:44, 28 September 2010

2010-09-28T15:44:19Z

2010-05-03T07:09:54Z

2009-08-11T10:41:57Z

2009-04-16T11:21:29Z

←Older revision		Revision as of 11:21, 16 April 2009
Line 4:		Line 4:

	'''Apex Destiny 6100''' is an alarm system.		'''Apex Destiny 6100''' is an alarm system.

			'''NOTE:''' This security panel should be supported out of the box using the 6100ICM and applying the VistaICM device to it. This needs to be tested by someone who has this security panel and can confirm that the 6100ICM works out of the box.

	== Installation ==		== Installation ==

2007-12-02T14:55:36Z

Apex Destiny 6100 moved to Apex Destiny-6100

←Older revision	Revision as of 14:55, 2 December 2007
(No difference)

2007-10-05T14:24:11Z

added to "serial" category

←Older revision		Revision as of 14:24, 5 October 2007
Line 1:		Line 1:
	[[Category: Hardware]]		[[Category: Hardware]]
	[[Category: Security]]		[[Category: Security]]
			[[Category: Serial]]

	'''Apex Destiny 6100''' is an alarm system.		'''Apex Destiny 6100''' is an alarm system.

2007-10-05T14:18:53Z

moved categories

←Older revision		Revision as of 14:18, 5 October 2007
Line 1:		Line 1:
			[[Category: Hardware]]
			[[Category: Security]]

	'''Apex Destiny 6100''' is an alarm system.		'''Apex Destiny 6100''' is an alarm system.

Line 22:		Line 25:

	Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.		Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.

	~~[[Category: Security]]~~

2007-09-26T22:11:18Z

←Older revision		Revision as of 22:11, 26 September 2007
Line 1:		Line 1:
			'''Apex Destiny 6100''' is an alarm system.

	== Installation ==		== Installation ==

Line 21:		Line 23:
	Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.		Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.


	~~[[Category: Hardware]]~~
	[[Category: Security]]		[[Category: Security]]

2007-09-06T01:24:21Z

←Older revision		Revision as of 01:24, 6 September 2007
Line 1:		Line 1:
	~~{{Plutoperm}}~~
	== Installation ==		== Installation ==

Line 21:		Line 20:

	Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.		Using the memory location access commands, we took a snapshots of the memory (you can only query 32 - 0x20 - bytes at a time, so getting a snapshot over the serial port takes a bit of a time) and reverse-engineered the memory map.


			[[Category: Hardware]]
			[[Category: Security]]

2007-03-27T09:47:28Z

←Older revision		Revision as of 09:47, 27 March 2007
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>== Installation ==		{{Plutoperm}}
			== Installation ==

	In order to setup the Apex system, you first need to connect it to a power supply, set the sensors and tie them to the inputs on the board from the panel, and also connect the wall panel to the main panel. You can find a very thorough description in the installation manual supplied by HoneyWell (can be downloaded in [http://www.security.honeywell.com/hsce/resources/literature/index.html the support section] of the security site).		In order to setup the Apex system, you first need to connect it to a power supply, set the sensors and tie them to the inputs on the board from the panel, and also connect the wall panel to the main panel. You can find a very thorough description in the installation manual supplied by HoneyWell (can be downloaded in [http://www.security.honeywell.com/hsce/resources/literature/index.html the support section] of the security site).