E-Fon (Switzerland) - Revision history

Mcefan at 22:28, 19 October 2012

2012-10-19T22:28:56Z

←Older revision		Revision as of 22:28, 19 October 2012
Line 2:		Line 2:
	[[Category: Telecom]]		[[Category: Telecom]]
	[[Category: Phone Lines]]		[[Category: Phone Lines]]
	~~[[Category: Tutorials]]~~

	<h2>Setup for <b>E-FON</b></h2>		<h2>Setup for <b>E-FON</b></h2>

Zaerc at 14:20, 18 October 2010

2010-10-18T14:20:52Z

@@ Line 1: / Line 1: @@
 <h2>Setup for <b>E-FON</b></h2>
 http://www.e-fon.ch/
@@ Line 41: / Line 46: @@
 <p>Select the extension to ring, or select default incoming extension</p>
 <p>Apply your changes by clicking on red line.</p>

Rwilson131 at 04:59, 14 October 2007

2007-10-14T04:59:40Z

←Older revision		Revision as of 04:59, 14 October 2007
Line 1:		Line 1:
	<h2>Setup for <b>E-FON</b></h2>		<h2>Setup for <b>E-FON</b></h2>
			http://www.e-fon.ch/
	==Automatic Setup==		==Automatic Setup==
	The setup is automatic from the House Setup Wizard using the following script		The setup is automatic from the House Setup Wizard using the following script

Rwilson131 at 04:54, 14 October 2007

2007-10-14T04:54:43Z

←Older revision		Revision as of 04:54, 14 October 2007
Line 1:		Line 1:
	<h2>Setup for <b>E-FON</b></h2>		<h2>Setup for <b>E-FON</b></h2>
			==Automatic Setup==
			The setup is automatic from the House Setup Wizard using the following script
			/usr/pluto/bin/create_amp_efon.pl
			==Manual Setup==
	<p>Go to 'Trunks' section</p>		<p>Go to 'Trunks' section</p>
	<p>Add a IAX2 trunk</p>		<p>Add a IAX2 trunk</p>

Rwilson131 at 04:52, 14 October 2007

2007-10-14T04:52:22Z

←Older revision		Revision as of 04:52, 14 October 2007
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table><h2>Setup for <b>E-FON</b></h2>		<h2>Setup for <b>E-FON</b></h2>
	<p>Go to 'Trunks' section</p>		<p>Go to 'Trunks' section</p>
	<p>Add a IAX2 trunk</p>		<p>Add a IAX2 trunk</p>
Line 36:		Line 36:
	<p>Select the extension to ring, or select default incoming extension</p>		<p>Select the extension to ring, or select default incoming extension</p>
	<p>Apply your changes by clicking on red line.</p>		<p>Apply your changes by clicking on red line.</p>
			[[Category: Phone Lines]]

Wikiadmin: Imported document

2006-06-05T16:47:56Z

Imported document

New page

<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table><h2>Setup for E-FON</h2>
Go to 'Trunks' section
Add a IAX2 trunk
On 'Outgoing Dial Rules' add <pre>9|.</pre>
this will be the prefix to place call to E-FON network
On 'Outgoing Settings' set trunk name to
<pre>efon</pre> and peer details to
<pre>callow=alaw
auth=md5
callerid="YOUR_NAME" YOUR_EFON_NUMBER
canreinvite=no
disallow=all
host=YOUR_EFON_PROXY
nat=yes
qualify=no
secret=YOUR_EFON_PASSWORD
type=peer
username=YOUR_EFON_NUMBER
</pre>
On 'Incoming Settings' set usercontext to
<pre>YOUR_EFON_NUMBER</pre> and user details to
<pre>auth=md5
context=from-pstn
secret=YOUR_EFON_PASSWORD
type=user
username=YOUR_EFON_NUMBER
</pre>
On 'Registration' set registration string to
<pre>YOUR_EFON_NUMBER:YOUR_EFON_PASSWORD@YOUR_EFON_PROXY</pre>
Go to Outbound Routing section
Set route name to <pre>efon</pre>
Set dial patterns to <pre>9|.</pre>
Set trunk sequence to <pre>IAX2/efon</pre>
Go to DID Routes section
Set number to <pre>YOUR EFON NUMBER</pre>
Select the extension to ring, or select default incoming extension
Apply your changes by clicking on red line.