Focus events - Revision history

Rwilson131: Category

2008-12-02T00:20:06Z

Rwilson131: remove pluto warning and spelling

2008-12-02T00:19:38Z

remove pluto warning and spelling

←Older revision		Revision as of 00:19, 2 December 2008
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>'''OnUp'''		'''OnUp'''

	The user press the change focus to previous control.		The user press the change focus to previous control.
Line 21:		Line 21:
	'''OnCancel'''		'''OnCancel'''

	The user wants to cancel all settings from current screen and if are more screens, to go to previous screen. ~~Ussually~~ on '''''OnCancel''''' command the '''''$previous''''' command will follow.		The user wants to cancel all settings from current screen and if are more screens, to go to previous screen. Usually on '''''OnCancel''''' command the '''''$previous''''' command will follow.

	'''OnFocus'''		'''OnFocus'''
Line 29:		Line 29:
	'''OnLostFocus'''		'''OnLostFocus'''

	If special code should run when a button ~~becames~~ disable, you may override that event (for instance to play a small sound here)		If special code should run when a button becomes disable, you may override that event (for instance to play a small sound here)

Wikiadmin at 06:47, 13 April 2006

2006-04-13T06:47:39Z

←Older revision		Revision as of 06:47, 13 April 2006
Line 22:		Line 22:

	The user wants to cancel all settings from current screen and if are more screens, to go to previous screen. Ussually on '''''OnCancel''''' command the '''''$previous''''' command will follow.		The user wants to cancel all settings from current screen and if are more screens, to go to previous screen. Ussually on '''''OnCancel''''' command the '''''$previous''''' command will follow.

			'''OnFocus'''

			If special code should run when a button is enable, you may override that event (for instance to play a small sound here)

			'''OnLostFocus'''

			If special code should run when a button becames disable, you may override that event (for instance to play a small sound here)

Wikiadmin at 07:18, 11 April 2006

2006-04-11T07:18:00Z

New page

<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>'''OnUp'''

The user press the change focus to previous control.

'''OnDown'''

The user press the change focus to next focus control.

'''OnLeft'''

The user wants to decrease the value shown to the control to be decreased.

'''OnRight'''

The user wants to decrease the value shown to the control to be increased.

'''OnEnter'''

The user wants to apply all settings from current screen and if are more screens, to go to following screen. Ussually on '''''OnEnter''''' command the '''''$next''''' command will follow.

'''OnCancel'''

The user wants to cancel all settings from current screen and if are more screens, to go to previous screen. Ussually on '''''OnCancel''''' command the '''''$previous''''' command will follow.

←Older revision		Revision as of 00:20, 2 December 2008
Line 1:		Line 1:
			[[Category:Programmer's Guide]]
	'''OnUp'''		'''OnUp'''