Gyration-GYR3101US-codes - Revision history

Mcefan at 22:48, 19 October 2012

2012-10-19T22:48:29Z

←Older revision		Revision as of 22:48, 19 October 2012
Line 1:		Line 1:
	{{versioninfo}}		{{versioninfo}}
			[[category: Input]]
			[[Category:Remote Controls]]

	This page is being superceded by [[GYR3101 Integration Notes]]		This page is being superceded by [[GYR3101 Integration Notes]]

Line 713:		Line 716:

	</pre>		</pre>
	~~[[category: tutorials]]~~
	~~[[category: Input]]~~

Wierdbeard65 at 18:16, 3 May 2010

2010-05-03T18:16:27Z

←Older revision		Revision as of 18:16, 3 May 2010
Line 1:		Line 1:
			{{versioninfo}}
	This page is being superceded by [[GYR3101 Integration Notes]]		This page is being superceded by [[GYR3101 Integration Notes]]

Tschak909: added supercede note.

2009-04-18T04:53:52Z

added supercede note.

←Older revision		Revision as of 04:53, 18 April 2009
Line 1:		Line 1:
			This page is being superceded by [[GYR3101 Integration Notes]]

	== ToDo ==		== ToDo ==

Langstonius at 16:50, 20 June 2008

2008-06-20T16:50:48Z

←Older revision		Revision as of 16:50, 20 June 2008
Line 710:		Line 710:

	</pre>		</pre>
			[[category: tutorials]]
			[[category: Input]]

Esperanto at 19:17, 5 March 2008

2008-03-05T19:17:42Z

←Older revision		Revision as of 19:17, 5 March 2008
Line 1:		Line 1:
			== ToDo ==

			The best solution would be if we could make it work without evrouter. Then we should need some way to have the higher keyevents in X. Any suggestions??


			Using [http://www.bedroomlan.org/~alexios/coding_evrouter.html evrouter] we would still need the following:
			* LinuxMCE should recognize the remote properly (now it saids it's a GO Cordless GC1005M but 'Registered: No')
			* This means we should reuse the fiire chief template (if it's possible to reroute it that way) or create a new one
			* Evrouter should route all high events to have the proper actions (so to key events or shell commands) (see the [[Gyration-GYR3101US-codes#Working_document_for_usage_with_evrouter \| template]])
			* Evrouter should be supplied with Lmce
			* it should have a proper way to automaticly start evrouter with the right configuration


	== Code table ==		== Code table ==
	{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"		{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"

Esperanto at 08:55, 3 March 2008

2008-03-03T08:55:33Z

←Older revision		Revision as of 08:55, 3 March 2008
Line 1:		Line 1:
	== Code table ==		== Code table ==
	{\| class="wikitable"		{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 39:		Line 39:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 60:		Line 61:
	\| 100		\| 100
	\| key/105		\| key/105

	\|-		\|-
	\| OK/Enter/Select		\| OK/Enter/Select
Line 83:		Line 83:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 102:		Line 103:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 133:		Line 135:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 156:		Line 159:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 211:		Line 215:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 226:		Line 231:
	\|}		\|}

	{\| class="wikitable"
			{\| class="wikitable" border="1" cellpadding="5" cellspacing="0"
	\|-		\|-
	! name		! name
Line 252:		Line 258:
	\| key/410		\| key/410
	\|}		\|}


	== Picture ==		== Picture ==

Esperanto at 07:49, 3 March 2008

2008-03-03T07:49:19Z

←Older revision		Revision as of 07:49, 3 March 2008
Line 1:		Line 1:
			== Code table ==
	{\| class="wikitable"		{\| class="wikitable"
	\|-		\|-
Line 252:		Line 253:
	\|}		\|}

			== Picture ==
	[[Image:Gyration-GYR3101US-codes.png]]		[[Image:Gyration-GYR3101US-codes.png]]


	Device Template info (based on template #1848)		== Device Template info (based on template #1848) ==
	<pre>		<pre>
	The Device Template.		The Device Template.
Line 345:		Line 346:
	</pre>		</pre>

	Working document for usage with evrouter		== Working document for usage with evrouter ==
	<pre>		<pre>
	# Stop		# Stop
Line 479:		Line 480:


	evtest gives the following output:		== evtest output ==
			evtest ( apt-get install lineakd ) gives the following output:

	<pre>		<pre>
	Input driver version is 1.0.0		Input driver version is 1.0.0

Esperanto at 10:56, 2 March 2008

2008-03-02T10:56:19Z

Show changes

Esperanto at 02:01, 2 March 2008

2008-03-02T02:01:06Z

←Older revision		Revision as of 02:01, 2 March 2008
Line 343:		Line 343:

	input,100202,U		input,100202,U
			</pre>

			Working document for usage with evrouter
			<pre>
			# Stop
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/166 "fill this in!"

			# Record
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/167 "XKey/R"

			# Pause
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/119 "XKey/P"

			# Play
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/207 "XKey/P"

			# Rewind
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/168 "XKey/Left"

			# Fast Forward
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/208 "XKey/Right"

			# Skip Back
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/165 "XKey/Home"

			# Skip Forward
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/163 "XKey/End"

			# Guide
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/362 "XKey/M"

			# Up
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/103 "fill this in!"

			# Left
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/105 "fill this in!"

			# Right
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/106 "fill this in!"

			# Down
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/108 "fill this in!"

			# Back
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/158 "fill this in!"

			# Info
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/130 "XKey/I"

			# OK/Enter
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/28 "fill this in!"

			# Volume Up
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/115 "XKey/F11"

			# Volume Down
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/114 "XKey/F10"

			# Channel Up
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/402 "XKey/Up"

			# Channel Down
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/403 "XKey/Down"

			# Mute
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/113 "XKey/F9"

			# 1
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/2 "fill this in!"
			#
			# 2
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/3 "fill this in!"
			#
			# 3
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/4 "fill this in!"
			#
			# 4
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/5 "fill this in!"
			#
			# 5
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/6 "fill this in!"
			#
			# 6
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/7 "fill this in!"
			#
			# 7
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/8 "fill this in!"
			#
			# 8
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/9 "fill this in!"
			#
			# 9
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/10 "fill this in!"
			#
			# 0
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/11 "fill this in!"
			#
			# *
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/42 "fill this in!"
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/9 "fill this in!"
			#
			# #
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/42 "fill this in!"
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/4 "fill this in!"

			# Clear
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/1 "fill this in!"


			# Other /dev/input/eventY events:
			# Left Click
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/272 "fill this in!"
			#
			# Right Click
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/273 "fill this in!"

			# Live TV
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/377 "XKey/C"

			# Windows
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/102 "XKey/Alt_L+Control_L+BackSpace"

			# Pictures
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/226 "fill this in!"
			#
			# Music
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/391 "fill this in!"
			#
			# Video
			# "Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/393 "fill this in!"

			# DVD Menu
			"Gyration Gyration RF Technology Receiver" "/dev/input/event*" none key/410 "XKey/O"
	</pre>		</pre>

Esperanto at 01:59, 2 March 2008

2008-03-02T01:59:32Z

←Older revision		Revision as of 01:59, 2 March 2008
Line 254:		Line 254:

	[[Image:Gyration-GYR3101US-codes.png]]		[[Image:Gyration-GYR3101US-codes.png]]


			Device Template info (based on template #1848)
			<pre>
			The Device Template.
			Values taken from the gyration template for the fiire-chief.


			These values are probably the same as on the fiire-chief:
			1,10,U,Y
			2,11,U,Y
			3,12,U,Y
			4,13,U,Y
			5,14,U,Y
			6,15,U,Y
			7,16,U,Y
			8,17,U,Y
			9,18,U,Y
			0,19,U,Y
			shortcut1,10,H,Y
			shortcut2,11,H,Y
			shortcut3,12,H,Y
			shortcut4,13,H,Y
			shortcut5,14,H,Y
			shortcut6,15,H,Y
			shortcut7,16,H,Y
			shortcut8,17,H,Y
			shortcut9,18,H,Y
			shortcut0,19,H,Y

			fastforward,180,D
			Rewind,152,D
			Play,179,D
			Stop,164,D

			Down,104,R,Y
			Up,98,R,Y
			Left,100,R,Y
			Right,102,R,Y
			ok,36,D,Y
			enter,36,D,Y
			Record,177,D
			SkipNext,153,R
			SkipPrior,144,R

			These have standard 'xev' output keys (and differ from the fiire):
			Clear,9,D
			voldn,176,R
			VolUp,174,R


			How to set these and which they are is still the question:
			Power,100130,U
			Halt,100130,H

			red,100070,U
			green,100073,U
			yellow,100071,U
			blue,100074,U
			shortcutr,100070,H
			shortcutg,100073,H
			shortcuty,100071,H
			shortcutb,100074,H
			Music,100071,U
			Videos,100074,U
			tv,100073,U
			Pictures,100070,U

			enter,108,D,Y

			chup,100156,R
			chdown,100157,R

			Pause,162,D
			Pause,110,D

			Mute,100226,D

			menu,100194,U
			avwizard,100194,H

			Guide,100141,D

			Back,100193,D

			info,100201,U
			help,100201,H

			input,100202,U
			</pre>