Hauppauge Nova-HD-S2 - Revision history

Zaerc at 15:57, 29 September 2010

2010-09-29T15:57:14Z

←Older revision		Revision as of 15:57, 29 September 2010
Line 1:		Line 1:
			[[Category: Hardware]]
			[[Category: Video]]
			[[Category: TV Cards]]
	{{versioninfo}}		{{versioninfo}}
	~~[[Category: Video]]~~
	~~[[Category: TV Cards]]~~
	[[Image:Novahds2 top.jpg]]		[[Image:Novahds2 top.jpg]]

Kezza at 09:50, 4 May 2010

2010-05-04T09:50:59Z

←Older revision		Revision as of 09:50, 4 May 2010
Line 1:		Line 1:
			{{versioninfo}}
	[[Category: Video]]		[[Category: Video]]
	[[Category: TV Cards]]		[[Category: TV Cards]]

Maverick0815: /* Installing The Drivers and Firmware */

2009-10-18T11:48:12Z

Installing The Drivers and Firmware

←Older revision		Revision as of 11:48, 18 October 2009
Line 29:		Line 29:
	Now we need to unpack the firmware and put it in the right place:		Now we need to unpack the firmware and put it in the right place:

	~~wget http://tevii.com/Tevii_linuxdriver_0815.rar~~
	unrar x Tevii_linuxdriver_0815.rar		unrar x Tevii_linuxdriver_0815.rar
	cp tevii_linuxdriver_0815/fw/dvb-fe-cx24116.fw /lib/firmware/dvb-fe-cx24116-1.23.86.1.fw		cp tevii_linuxdriver_0815/fw/dvb-fe-cx24116.fw /lib/firmware/dvb-fe-cx24116-1.23.86.1.fw

Maverick0815: /* Installing The Drivers and Firmware */

2009-10-07T09:54:53Z

Installing The Drivers and Firmware

@@ Line 17: / Line 17: @@
 == Installing The Drivers and Firmware ==
-Download and install the v4l-dvb drivers
+To keep things a bit in order and together I prefer to
-[http://www.linuxtv.org/hg/]
+ cd /usr/local/src
-  hg clone http://linuxtv.org/hg/v4l-dvb
+Then we should get the firmware. There are severel verions out there, but I use this one, since it is the most recent I could get:
-  cd v4l-dvb
   make
   make install
 now reboot, and check that the card has loaded
   dmesg | grep cx88
 you should get an output stating "hvr-4000-lite / Nova-HD-S2" somewhere.
 == Scan for Channels ==

Maverick0815: /* Driver Information */

2009-10-07T09:24:38Z

Driver Information

←Older revision		Revision as of 09:24, 7 October 2009
Line 11:		Line 11:

	== Driver Information ==		== Driver Information ==
	This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in LinuxMCE 0710.		This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S2 element of the HVR-4000 card working in LinuxMCE 0710 as well as the current LinuxMCE 8.10 alpha.

	The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.		The DVB-S2 element on the NOVA-HD-S2 has run successfully on LMCE 0710/ 8.10 alpha using VDR and MythTV.
			Previously multiproto-drivers were required to receive DVB-S2. However something new called S2API has come up from the guys and gals at LinuxTV.org, which -as I understand it- renders multiproto obsolete. It is included in v4l and in kernel v2.6.28.
	~~Unfortunately, the current version of VDR does not support HD /~~ DVB-S2 ~~(as of LinuxMCE 0710)~~. ~~The driver listed here only gets~~ the ~~DVB-S element running~~. ~~In later versions of LinuxMCE this will become obsolete~~, ~~particularly when later versions of VDR are used. The experimental VDR 1.7.X will only work using Multiproto drivers, but these will support the DVB~~-~~S2 element of this card~~.

	~~See [http://www~~.~~linuxtv~~.~~org/wiki/index.php/Hauppauge_WinTV-HVR-4000 here] for further information on driver status, and how to compile the multiproto driver~~.

	== Installing The Drivers and Firmware ==		== Installing The Drivers and Firmware ==

Raffaello.secchi at 13:00, 26 February 2009

2009-02-26T13:00:21Z

←Older revision		Revision as of 13:00, 26 February 2009
Line 22:		Line 22:
	Download and install the v4l-dvb drivers		Download and install the v4l-dvb drivers
	[http://www.linuxtv.org/hg/]		[http://www.linuxtv.org/hg/]
			hg clone http://linuxtv.org/hg/v4l-dvb
			cd v4l-dvb
			make
			make install

	Change into the downloaded directory, and open up a console. Type:		Change into the downloaded directory, and open up a console. Type:

Raffaello.secchi: /* Installing The Drivers and Firmware */

2009-02-03T19:16:48Z

Installing The Drivers and Firmware

←Older revision		Revision as of 19:16, 3 February 2009
Line 20:		Line 20:

	== Installing The Drivers and Firmware ==		== Installing The Drivers and Firmware ==
	Download the ~~patched~~ [http://www.~~file-upload~~.~~net~~/~~download-434453~~/~~hvr4000-ce31158b75ae.tar.gz.html v4l-dvb driver~~]		Download and install the v4l-dvb drivers
			[http://www.linuxtv.org/hg/]

	Change into the downloaded directory, and open up a console. Type:		Change into the downloaded directory, and open up a console. Type:

Gazlang: /* Driver Information */

2008-07-24T12:19:47Z

Driver Information

←Older revision		Revision as of 12:19, 24 July 2008
Line 17:		Line 17:
	Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LinuxMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LinuxMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 1.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.		Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LinuxMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LinuxMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 1.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.

	See [~~[Hauppauge WinTV~~-HVR-4000]] for further information on driver status, and how to compile the multiproto driver.		See [http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4000 here] for further information on driver status, and how to compile the multiproto driver.

	== Installing The Drivers and Firmware ==		== Installing The Drivers and Firmware ==

Marie.o: Beautified and spell checked the page.

2008-07-03T18:23:45Z

Beautified and spell checked the page.

←Older revision		Revision as of 18:23, 3 July 2008
Line 2:		Line 2:
	[[Category: TV Cards]]		[[Category: TV Cards]]
	[[Image:Novahds2 top.jpg]]		[[Image:Novahds2 top.jpg]]


	Digital satellite TV and radio for your PC. Watch free-to-air satellite TV, in a window or full screen on your PC!		Digital satellite TV and radio for your PC. Watch free-to-air satellite TV, in a window or full screen on your PC!
	Record digital satellite TV to your PC's hard disk in original MPEG-2 quality. Digital TV recordings will typically take 1,5 Gigabytes of disk space per hour.		*Record digital satellite TV to your PC's hard disk in original MPEG-2 quality. Digital TV recordings will typically take 1,5 Gigabytes of disk space per hour.
	Pause digital satellite TV with instant replay.		*Pause digital satellite TV with instant replay.
	Listen to digital satellite DVB-S/DVB-S2 radio.		*Listen to digital satellite DVB-S/DVB-S2 radio.
	DiSEqC 1.0 support.		*DiSEqC 1.0 support.
	Includes Hauppauge new IR remote control, for easy control of TV watching, record and play functions.		*Includes Hauppauge new IR remote control, for easy control of TV watching, record and play functions.



	== ~~'''~~Driver Information~~'''~~ ==		== Driver Information ==
			This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in LinuxMCE 0710.


	This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in ~~LMCE~~ 0710.

	The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.		The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.

	Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of ~~LMCE~~ 0710). The driver listed here only gets the DVB-S element running. In later versions of ~~LMCE~~ this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.		Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LinuxMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LinuxMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 1.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.

	~~See [http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4000 here] for further information on driver status, and how to compile the multiproto driver.~~



	~~== '''Installing The Drivers and Firmware''' ==~~



	~~Download the patched v4l-dvb driver from [http://www.file-upload.net/download-434453/hvr4000-ce31158b75ae.tar.gz.html here]~~


	~~Change into the downloaded directory, and open up a konsole. Type:~~


	~~make~~

	~~sudo make install~~

			See [[Hauppauge WinTV-HVR-4000]] for further information on driver status, and how to compile the multiproto driver.

			== Installing The Drivers and Firmware ==
			Download the patched [http://www.file-upload.net/download-434453/hvr4000-ce31158b75ae.tar.gz.html v4l-dvb driver]

			Change into the downloaded directory, and open up a console. Type:
			make
			sudo make install
	Now fetch the firmware:		Now fetch the firmware:
			wget ftp://167.206.143.11/outgoing/Oxford/88x_2_119_25023_WHQL.zip

	wget ftp://167.206.143.11/outgoing/Oxford/88x_2_119_25023_WHQL.zip


	unzip:		unzip:
			unzip -jo 88x_2_119_25023_WHQL.zip Driver88/hcw88bda.sys

	unzip -jo 88x_2_119_25023_WHQL.zip Driver88/hcw88bda.sys


	and put it in place:		and put it in place:
			dd if=hcw88bda.sys of=/lib/firmware/dvb-fe-cx24116.fw skip=81768 bs=1 count=32522

	dd if=hcw88bda.sys of=/lib/firmware/dvb-fe-cx24116.fw skip=81768 bs=1 count=32522



	now reboot, and check that the card has loaded		now reboot, and check that the card has loaded
			dmesg \| grep cx88

	dmesg \| grep cx88



	you should get an output stating "hvr-4000-lite / Nova-HD-S2" somewhere.		you should get an output stating "hvr-4000-lite / Nova-HD-S2" somewhere.

			== Scan for Channels ==

			See LiuxMCE [[VDR]] wiki entry.

	~~== '''Scan for Channels''' ==~~



	~~see~~ [~~http://wiki.linuxmce.org/index.php/~~VDR ~~here~~] ~~for the VDR~~ wiki



	Instead of the scan command used in the VDR wiki I used:		Instead of the scan command used in the VDR wiki I used:
			scan -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf

	scan -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf


	Where my satellite is Astra-28.2E (the BSkyB (Sky-tv-uk) satellite)		Where my satellite is Astra-28.2E (the BSkyB (Sky-tv-uk) satellite)


	To scan free-to-air channels only add an "-x 0" in the command. e.g.		To scan free-to-air channels only add an "-x 0" in the command. e.g.
			scan -x 0 -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf
			Add the created channels.conf to VDR in the LinuxMCE admin / advanced / configuration / VDR setup as per the VDR wiki
	scan -x 0 -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf



	Add the created channels.conf to VDR in the ~~LMCE~~ admin / advanced / configuration / VDR setup as per the VDR wiki

Gazlang at 10:16, 3 July 2008

2008-07-03T10:16:42Z

←Older revision		Revision as of 10:16, 3 July 2008
Line 17:		Line 17:


	The DVB-S element on ~~this card~~ has run successfully on LMCE 0710 using VDR.		This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in LMCE 0710.

			The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.

	Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.		Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.

			See [http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4000 here] for further information on driver status, and how to compile the multiproto driver.