How to set main office phoneline - Revision history

Mcefan at 02:06, 20 October 2012

2012-10-20T02:06:11Z

←Older revision		Revision as of 02:06, 20 October 2012
Line 1:		Line 1:
	[[Category: ~~Tutorials~~]]		[[Category: telecom]]
	~~[[Category: Documentation]]~~

	If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.		If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.

Ray N at 16:58, 13 August 2009

2009-08-13T16:58:05Z

←Older revision		Revision as of 16:58, 13 August 2009
Line 1:		Line 1:
	[[Category:~~Internal_Documents~~]]		[[Category: Tutorials]]
			[[Category: Documentation]]

	If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.		If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.

Juliet at 08:28, 19 March 2007

2007-03-19T08:28:12Z

←Older revision		Revision as of 08:28, 19 March 2007
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>[[Category:Internal_Documents]]		[[Category:Internal_Documents]]
	If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.		If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.

Line 28:		Line 28:
	== Test if everything is working fine ==		== Test if everything is working fine ==

	Dial 918777588648, it should say something like "Welcome to ~~pluto~~....", then press "0", and wait for incoming call.		Dial 918777588648, it should say something like "Welcome to LinuxMCE....", then press "0", and wait for incoming call.

Wikiadmin at 09:45, 24 May 2006

2006-05-24T09:45:51Z

←Older revision		Revision as of 09:45, 24 May 2006
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>[[Category:~~Tutorials~~]]		<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>[[Category:Internal_Documents]]

	If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.		If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.

Wikiadmin at 09:42, 24 May 2006

2006-05-24T09:42:28Z

←Older revision		Revision as of 09:42, 24 May 2006
Line 19:		Line 19:

	== Configs on .150 changed ==		== Configs on .150 changed ==
			Remember that 10.0.0.150 has many IP addresses (150, 163, 164, 165, 166, 167, 168, 169, 170, 174, 175), so modifiing something in telecom related pages may screw everything.

			To repair it follow this steps:
			* go to ''http://10.0.0.150/pluto-admin/amp/admin/config.php''
			* delete all trunks, incoming and outgoing routing
			* run ''/usr/pluto/bin/create_amp_broadvoice.pl'' with needed parameters
			* go to ''http://10.0.0.150/pluto-admin/amp/admin/config.php?display=7&extdisplay=9543372199/'' and set ''destination'' to ''3314''

			== Test if everything is working fine ==

			Dial 918777588648, it should say something like "Welcome to pluto....", then press "0", and wait for incoming call.

Wikiadmin at 09:29, 24 May 2006

2006-05-24T09:29:47Z

New page

<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table>[[Category:Tutorials]]

If you need to test something with Cisco7960 or (by accident) modified asterisk configuration on 10.0.0.150, and you still want broadvoice number to ring in the office read this manual.

== Cisco 7960 changed ==
If you used the phone for tests (and set it to get ip by DHCP) you have to revert those changes :
* set DHCP to NO
* set IP to 10.0.0.203
* set MASK to .255.255.255.0
* set Router to 10.0.0.1
* set NameServer to 10.0.0.1
* set TFTP to 10.0.0.150 (on 10.0.0.150 in /tftpboot you'll find it's configuration files, no need to modify)
* reboot the phone
* if something went wrong (it hasn't registered in 1-2 minutes) recheck all phone settings.

You have to do so because in 10.0.0.* network we don't have DCHP that will set TFTP, and so on.

When you plug the phone in one of the testing network and set it to DHCP it will fill those automatically.

== Configs on .150 changed ==