InteractiveTechnologies CueServer-Pro-CS-800 - Revision history

RayBe: Added category: GSD

2016-07-11T14:51:24Z

Added category: GSD

←Older revision		Revision as of 14:51, 11 July 2016
Line 1:		Line 1:
	[[Category: Automation]] [[Category: hardware]]		[[Category: Automation]] [[Category: hardware]]
			[[Category: GSD]]
	This is a template for a DMX lighting controller by Interactive technologies - model [http://www.interactive-online.com/products/cueserver/overview Cueserver pro800]		This is a template for a DMX lighting controller by Interactive technologies - model [http://www.interactive-online.com/products/cueserver/overview Cueserver pro800]
	Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)		Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)

Marie.o at 11:37, 6 November 2011

2011-11-06T11:37:38Z

←Older revision		Revision as of 11:37, 6 November 2011
Line 1:		Line 1:
	[[Category: Automation]] [[Category: hardware]]		[[Category: Automation]] [[Category: hardware]]
	This is a template for a DMX lighting controller by Interactive technologies - model ~~Cueserver pro800~~		This is a template for a DMX lighting controller by Interactive technologies - model [http://www.interactive-online.com/products/cueserver/overview Cueserver pro800]
	http://www.interactive-online.com/products/cueserver/overview
	Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)		Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)

Marie.o at 13:18, 23 October 2011

2011-10-23T13:18:27Z

@@ Line 4: / Line 4: @@
 Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)
- in the RUBY CODE under "Ruby Internal Commands"-"#384 Process Receive Command For Child "add
+in the RUBY CODE under "Ruby Internal Commands"-"#384 Process Receive Command For Child "add
-id=device_.childdevices_[cmd.devidto_].devdata_[12]#get child device number
+ id=device_.childdevices_[cmd.devidto_].devdata_[12]#get child device number
-if cmd.id_==192 #192 is on
+== Things To Do ==
+* get #184 the dimmer command to work correctly
-conn_.Send("[c"+id+"atfl]\r") #set id to full
+* add log/messages to keep lmce up to date
+* intergrate the 8 contact closures on the cueserver this could work as alarm interface
-end
+* get it to work over the ethernet write a driver in c++

Zaerc: Cueserver dmx lighting moved to InteractiveTechnologies CueServer-Pro-CS-800: proper naming

2010-10-25T21:11:55Z

Cueserver dmx lighting moved to InteractiveTechnologies CueServer-Pro-CS-800: proper naming

←Older revision	Revision as of 21:11, 25 October 2010
(No difference)

Gonesurfing at 08:16, 5 September 2010

2010-09-05T08:16:04Z

←Older revision		Revision as of 08:16, 5 September 2010
Line 9:		Line 9:

	if cmd.id_==192 #192 is on		if cmd.id_==192 #192 is on

	conn_.Send("[c"+id+"atfl]\r") #set id to full		conn_.Send("[c"+id+"atfl]\r") #set id to full

	end		end

	if cmd.id_==193 #193 is off		if cmd.id_==193 #193 is off

	conn_.Send("[c"+id+"rel]\r") #relase id to zero		conn_.Send("[c"+id+"rel]\r") #relase id to zero

	end		end

	if cmd.id_==184 #184 dimmer		if cmd.id_==184 #184 dimmer

	conn_.Send("[c"+id+"at50]\r") #set id to 50% it should step the light up or down this is not working at present		conn_.Send("[c"+id+"at50]\r") #set id to 50% it should step the light up or down this is not working at present

	end		end


	THINGS TO DO		THINGS TO DO

	-get #184 the dimmer command to work correctly		-get #184 the dimmer command to work correctly

	-add log/messages to keep lmce up to date		-add log/messages to keep lmce up to date

	-intergrate the 8 contact closures on the cueserver this could work as alarm interface		-intergrate the 8 contact closures on the cueserver this could work as alarm interface
	-get it to work over the ethernet c++
			-get it to work over the ethernet write a driver in c++

Gonesurfing: New page: Category: Automation Category: hardware This is a template for a DMX lighting controller by Interactive technologies - model Cueserver pro800 http://www.interactive-online.com/p...

2010-09-05T08:07:47Z

New page: Category: Automation Category: hardware This is a template for a DMX lighting controller by Interactive technologies - model Cueserver pro800 http://www.interactive-online.com/p...

New page

[[Category: Automation]] [[Category: hardware]]
This is a template for a DMX lighting controller by Interactive technologies - model Cueserver pro800
http://www.interactive-online.com/products/cueserver/overview
Its very basic at the moment however it is working using the serial port I have followed the guide in the wiki "Implementing Clipsal Interface using Generic Serial Device"also adding in device data #76 COM Port ParityBit/Stop(string) #78 COM Port BaudRate(string)

in the RUBY CODE under "Ruby Internal Commands"-"#384 Process Receive Command For Child "add

id=device_.childdevices_[cmd.devidto_].devdata_[12]#get child device number

if cmd.id_==192 #192 is on
conn_.Send("[c"+id+"atfl]\r") #set id to full
end
if cmd.id_==193 #193 is off
conn_.Send("[c"+id+"rel]\r") #relase id to zero
end
if cmd.id_==184 #184 dimmer
conn_.Send("[c"+id+"at50]\r") #set id to 50% it should step the light up or down this is not working at present
end

THINGS TO DO
-get #184 the dimmer command to work correctly
-add log/messages to keep lmce up to date
-intergrate the 8 contact closures on the cueserver this could work as alarm interface
-get it to work over the ethernet c++