Linksys SPA3000 - Revision history

Mcefan at 02:55, 20 October 2012

2012-10-20T02:55:24Z

←Older revision		Revision as of 02:55, 20 October 2012
Line 2:		Line 2:
	[[Category:Telecom]]		[[Category:Telecom]]
	[[Category:VoIP]]		[[Category:VoIP]]
	~~[[Category:Tutorials]]~~
	[[Category:ATA]]		[[Category:ATA]]
	{{merge\|Linksys SPA3102}}		{{merge\|Linksys SPA3102}}


	== General Information ==		== General Information ==

Line 28:		Line 29:

	Note: these instructions are obsolete. Go to the Linksys SPA3102 page for newest.		Note: these instructions are obsolete. Go to the Linksys SPA3102 page for newest.

			{{p}}

	== Setup ==		== Setup ==
Line 271:		Line 274:

	That should be it! Enjoy LMCE Telecom on your old analog phone line!		That should be it! Enjoy LMCE Telecom on your old analog phone line!

			{{p}}

	== Disconnect Tone ==		== Disconnect Tone ==
Line 294:		Line 299:
	So my settings is at 425@-30,425-30;4(.20/.20/1+2). Due to the simplicity of the Swiss disconnect tone I may not have needed to display the same Hz twice nor have a 4 repeat cycle pattern but it works this way and I haven't tested further.		So my settings is at 425@-30,425-30;4(.20/.20/1+2). Due to the simplicity of the Swiss disconnect tone I may not have needed to display the same Hz twice nor have a 4 repeat cycle pattern but it works this way and I haven't tested further.

			{{p}}

	== BUG REPORTS ==		== BUG REPORTS ==

Tred: /* General Information */

2012-01-16T15:47:35Z

General Information

←Older revision		Revision as of 15:47, 16 January 2012
Line 6:		Line 6:
	{{merge\|Linksys SPA3102}}		{{merge\|Linksys SPA3102}}
	== General Information ==		== General Information ==


			Note: '''these instructions are obsolete'''. Go to the Linksys SPA3102 page for newest.


	The Sipura (now bought out by Linksys) spa 3000 is a pstn (analog phone line) to Asterisk gateway device that provides a SIP interface for 1 FXO port (analog phone line) and 1 FXS port (analog phone). This allows you to use the Telecom section of LMCE, and use Asterisk to send/recieve/route phone calls.		The Sipura (now bought out by Linksys) spa 3000 is a pstn (analog phone line) to Asterisk gateway device that provides a SIP interface for 1 FXO port (analog phone line) and 1 FXS port (analog phone). This allows you to use the Telecom section of LMCE, and use Asterisk to send/recieve/route phone calls.
Line 23:		Line 27:
	:-:These Instructions are obsolete. Review the Linksys SPA3102 for current ones:-:		:-:These Instructions are obsolete. Review the Linksys SPA3102 for current ones:-:

	Note: these instructions are obsolete. Go to the Linksys SPA3102 page for newest.		Note: these instructions are obsolete. Go to the Linksys SPA3102 page for newest.

	== Setup ==		== Setup ==
	We are going to accomplish this setup in 3 steps:		We are going to accomplish this setup in 3 steps:

Tred: /* Setup */

2012-01-16T15:46:27Z

Setup

←Older revision		Revision as of 15:46, 16 January 2012
Line 23:		Line 23:
	:-:These Instructions are obsolete. Review the Linksys SPA3102 for current ones:-:		:-:These Instructions are obsolete. Review the Linksys SPA3102 for current ones:-:

			Note: these instructions are obsolete. Go to the Linksys SPA3102 page for newest.
	== Setup ==		== Setup ==
	We are going to accomplish this setup in 3 steps:		We are going to accomplish this setup in 3 steps:

Tred: /* Setup */

2012-01-16T15:45:11Z

Setup

←Older revision		Revision as of 15:45, 16 January 2012
Line 20:		Line 20:

	Please set aside some time to do this manual setup - as you will see, there are a lot of steps involved and it may take you quite some time!		Please set aside some time to do this manual setup - as you will see, there are a lot of steps involved and it may take you quite some time!

			:-:These Instructions are obsolete. Review the Linksys SPA3102 for current ones:-:

	== Setup ==		== Setup ==
Line 263:		Line 265:

	That should be it! Enjoy LMCE Telecom on your old analog phone line!		That should be it! Enjoy LMCE Telecom on your old analog phone line!


	== Disconnect Tone ==		== Disconnect Tone ==

Twodogs at 13:40, 8 November 2011

2011-11-08T13:40:57Z

←Older revision		Revision as of 13:40, 8 November 2011
Line 3:		Line 3:
	[[Category:VoIP]]		[[Category:VoIP]]
	[[Category:Tutorials]]		[[Category:Tutorials]]
			[[Category:ATA]]
	{{merge\|Linksys SPA3102}}		{{merge\|Linksys SPA3102}}
	== General Information ==		== General Information ==

Schmich at 16:53, 9 June 2011

2011-06-09T16:53:20Z

←Older revision		Revision as of 16:53, 9 June 2011
Line 278:		Line 278:

	B = Time in seconds for the silence		B = Time in seconds for the silence

			The -30 is the level in dB.

			The 1+2 is saying cycle the first and second tone. So for the example below you can just have 1 instead of 1+2.

	The default is 480@-30,620@-30;4(.25/.25/1+2) however this didn't work for me. I live in Switzerland where the disconnect tone is at 425Hz for 200ms followed by a silence at 200ms.		The default is 480@-30,620@-30;4(.25/.25/1+2) however this didn't work for me. I live in Switzerland where the disconnect tone is at 425Hz for 200ms followed by a silence at 200ms.

Schmich at 20:31, 7 June 2011

2011-06-07T20:31:28Z

←Older revision	Revision as of 20:31, 7 June 2011
Line 264:	Line 264:


		== Disconnect Tone ==
		If your line doesn't hang up after a call then you may need to change the disconnect tone. Different countries have different disconnect tones. Go to the SPA3000's configuration page, click on Admin Login and then Advanced. Now head to the PSTN Line tab. Scroll down to the PSTN Disconnect Detection. There is a setting called "Disconnect Tone" and that's what needs to change.

		The format entered needs to be of the following: X@-30,X@-30;Y(A/B/1+2)

		where:

		X = The frequency in Hz.

		Y = The cycles the pattern repeats

		A = Time in seconds for the frequency

		B = Time in seconds for the silence

		The default is 480@-30,620@-30;4(.25/.25/1+2) however this didn't work for me. I live in Switzerland where the disconnect tone is at 425Hz for 200ms followed by a silence at 200ms.
		So my settings is at 425@-30,425-30;4(.20/.20/1+2). Due to the simplicity of the Swiss disconnect tone I may not have needed to display the same Hz twice nor have a 4 repeat cycle pattern but it works this way and I haven't tested further.

Zaerc at 14:41, 18 October 2010

2010-10-18T14:41:13Z

←Older revision		Revision as of 14:41, 18 October 2010
Line 1:		Line 1:
			[[Category:Hardware]]
			[[Category:Telecom]]
			[[Category:VoIP]]
			[[Category:Tutorials]]
			{{merge\|Linksys SPA3102}}
	== General Information ==		== General Information ==

Line 267:		Line 272:

	- Incoming calls don't directly ring the house phone extension. All orbiters alert of the call, and the call can be directed to go to the house line, but I would have expected that the houseline would ring and could be picked up on a call with no orbiter interaction at all. (not quite sure if this a bug or not, of if this is how LMCE should handle it. Can anyone with VoIP confirm the behavior?) (UPDATE: Found the problem. This will not work until do the web admin portion of this - it will essentiall fix its self when I implement that code)		- Incoming calls don't directly ring the house phone extension. All orbiters alert of the call, and the call can be directed to go to the house line, but I would have expected that the houseline would ring and could be picked up on a call with no orbiter interaction at all. (not quite sure if this a bug or not, of if this is how LMCE should handle it. Can anyone with VoIP confirm the behavior?) (UPDATE: Found the problem. This will not work until do the web admin portion of this - it will essentiall fix its self when I implement that code)

	~~[[Category:Tutorials]][[Category:PSTN Setups]]~~

Zaerc: Sipura/Linksys spa3000 pstn interface moved to Linksys SPA3000

2010-10-18T14:38:05Z

Sipura/Linksys spa3000 pstn interface moved to Linksys SPA3000

←Older revision	Revision as of 14:38, 18 October 2010
(No difference)

Pw44 at 10:14, 11 March 2010

2010-03-11T10:14:31Z

←Older revision		Revision as of 10:14, 11 March 2010
Line 132:		Line 132:
	When prompted, enter 73738# from the telephone keypad. This will reset the unit to factory defaults.		When prompted, enter 73738# from the telephone keypad. This will reset the unit to factory defaults.

	Now go ahead and connect the spa3000 to your internal network switch. We have to assign it a static IP address, so again dial **** from the connected handset. When prompted, enter 110# and the IP address will be spoken back to you. Write it down. Open up a web browser on the network, and enter the IP address to go to the spa3000 admin page. In the upper right hand corner, click on the links for both Admin Login and Advanced.		Now go ahead and connect the spa3000's LAN port to your internal network switch. We have to assign it a static IP address, so again dial **** from the connected handset. When prompted, enter 110# and the IP address will be spoken back to you. Write it down. Open up a web browser on the network, and enter the IP address to go to the spa3000 admin page. In the upper right hand corner, click on the links for both Admin Login and Advanced.

	Go to the System tab. Under "Internet Connection Type" do the following:		Go to the System tab. Under "Internet Connection Type" do the following:
Line 140:		Line 140:
	Netmask: 255.255.255.0		Netmask: 255.255.255.0
	Gateway: 192.168.80.1		Gateway: 192.168.80.1

			Update for SPA-3102 <br>
			Router -> WAN Setup<br>
			set WAN Web Server to YES<br>
			disconnect the LAN port from the network and connect the WAN port to the network.<br>