Philips Hue - Revision history

RayBe: adding category's

2014-03-14T11:19:14Z

adding category's

←Older revision		Revision as of 11:19, 14 March 2014
Line 1:		Line 1:
	~~this~~ page is a work in progress and needs expanding (14-3-2014 RayBe)		[[Category: RF Control]]
			[[Category: Automation]]
			[[Category: Lighting]]
			[[Category: Hardware]]
			This page is a work in progress and needs expanding (14-3-2014 RayBe)
	[[Image:Philips_Hue.jpeg\|right]]		[[Image:Philips_Hue.jpeg\|right]]
	To install the Philips Hue Bridge and it lights:		To install the Philips Hue Bridge and its lights:
	* Setup the Philips Hue controller and its lights as described in the manual		* Setup the Philips Hue controller and its lights as described in the manual
	* Connect the Hue Bridge to the internal network of Linuxmce		* Connect the Hue Bridge to the internal network of Linuxmce

RayBe at 11:07, 14 March 2014

2014-03-14T11:07:15Z

←Older revision		Revision as of 11:07, 14 March 2014
Line 1:		Line 1:
	this page is a work in progress and needs expanding (14-3-2014 RayBe)		this page is a work in progress and needs expanding (14-3-2014 RayBe)
	[[Image:Philips_Hue.~~jpg~~\|right]]		[[Image:Philips_Hue.jpeg\|right]]
	To install the Philips Hue Bridge and it lights:		To install the Philips Hue Bridge and it lights:
	* Setup the Philips Hue controller and its lights as described in the manual		* Setup the Philips Hue controller and its lights as described in the manual

RayBe at 11:06, 14 March 2014

2014-03-14T11:06:25Z

←Older revision		Revision as of 11:06, 14 March 2014
Line 1:		Line 1:
	this page is a work in progress and needs expanding (14-3-2014 RayBe)		this page is a work in progress and needs expanding (14-3-2014 RayBe)
	[[Image:~~Philips Hue~~.jpg\|right]]		[[Image:Philips_Hue.jpg\|right]]
	To install the Philips Hue Bridge and it lights:		To install the Philips Hue Bridge and it lights:
	* Setup the Philips Hue controller and its lights as described in the manual		* Setup the Philips Hue controller and its lights as described in the manual

RayBe at 11:05, 14 March 2014

2014-03-14T11:05:16Z

←Older revision		Revision as of 11:05, 14 March 2014
Line 1:		Line 1:
	this page is a work in progress and needs expanding (14-3-2014 RayBe)		this page is a work in progress and needs expanding (14-3-2014 RayBe)
			[[Image:Philips Hue.jpg\|right]]
	To install the Philips Hue Bridge and it lights:		To install the Philips Hue Bridge and it lights:
	* Setup the Philips Hue controller and its lights as described in the manual		* Setup the Philips Hue controller and its lights as described in the manual

RayBe: First draft for the Philips Hue wiki

2014-03-14T10:58:44Z

First draft for the Philips Hue wiki

New page

this page is a work in progress and needs expanding (14-3-2014 RayBe)

To install the Philips Hue Bridge and it lights:
* Setup the Philips Hue controller and its lights as described in the manual
* Connect the Hue Bridge to the internal network of Linuxmce
* On a Orbiter you will get asked if Linuxmce should use the newly found Hue Device, select yes
* Now you get asked in which room the Hue-Controller must be setup, select any you want
* Log into webadmin and find the newly added Hue Controller, its under Wizard -> Devices -> Interfaces
* Click on 'Advanced'
* Click on 'Follow log' in the top right
* At this point Linuxmce is trying to add a user to your Hue-Bridge but can't because you didn't press the link-button on the bridge.
* Look in the log if there is a line stating: 'Setup command failed. Reason to follow::link button not pressed'
* Press the link-button on the Hue-Bridge and watch a Orbiter, you will get asked to reload the router.
* All the lights which you did setup in the Bridge get automatically added to the Wizard -> Devices -> Lights section of the webadmin.