QOrbiter Setup - Revision history

Marie.o: /* Configuration */

2016-06-30T05:01:03Z

Configuration

@@ Line 12: / Line 12: @@
 *Quick Reload the router when asked.
 *Note: It is no longer needed to run qOrbiterGenerator.php.
 ==Running the device==

GolgoJ4: /* Remote Access */

2016-04-11T16:15:13Z

Remote Access

←Older revision		Revision as of 16:15, 11 April 2016
Line 37:		Line 37:
	In order to use qOrbiter from outside your internal LinuxMCE network, you need to:		In order to use qOrbiter from outside your internal LinuxMCE network, you need to:
	*Open ports 2757 & 3450 on your firewall via webadmin		*Open ports 2757 & 3450 on your firewall via webadmin
			*Enter your public ip address to your core. Keep in mind there is no security, so you should be connecting via vpn
	[[Category:Programmer's Guide]][[Category:QML]][[category:QOrbiter]]		[[Category:Programmer's Guide]][[Category:QML]][[category:QOrbiter]]

GolgoJ4: /* Remote Access */

2016-04-11T16:14:16Z

Remote Access

←Older revision		Revision as of 16:14, 11 April 2016
Line 37:		Line 37:
	In order to use qOrbiter from outside your internal LinuxMCE network, you need to:		In order to use qOrbiter from outside your internal LinuxMCE network, you need to:
	*Open ports 2757 & 3450 on your firewall via webadmin		*Open ports 2757 & 3450 on your firewall via webadmin
	*Change the host line in LinuxMCE/config.xml on your device to your core's external IP address.

	[[Category:Programmer's Guide]][[Category:QML]][[category:QOrbiter]]		[[Category:Programmer's Guide]][[Category:QML]][[category:QOrbiter]]

Golgoj4: /* Configuration */

2014-09-30T17:56:23Z

Configuration

←Older revision		Revision as of 17:56, 30 September 2014
Line 19:		Line 19:

	sudo apt-get install subversion		sudo apt-get install subversion
	svn co http://svn.linuxmce.org/svn/~~branches/LinuxMCE-1004~~/src/qOrbiter/qOrbiter_src/qml /var/www/lmce-admin/skins && chmod -R 777 /var/www/lmce-admin/skins/android		svn co http://svn.linuxmce.org/svn/trunk/src/qOrbiter/qOrbiter_src/qml /var/www/lmce-admin/skins && chmod -R 777 /var/www/lmce-admin/skins/android

	*Note that this method will only get the android skins to save on bandwidth.		*Note that this method will only get the android skins to save on bandwidth.

Golgoj4: /* Configuration */

2013-08-21T23:36:03Z

Configuration

←Older revision		Revision as of 23:36, 21 August 2013
Line 19:		Line 19:

	sudo apt-get install subversion		sudo apt-get install subversion
	svn co http://svn.linuxmce.org/svn/~~trunk~~/src/qOrbiter/qOrbiter_src/qml/~~android~~/ /var/www/lmce-admin/skins/		svn co http://svn.linuxmce.org/svn/branches/LinuxMCE-1004/src/qOrbiter/qOrbiter_src/qml /var/www/lmce-admin/skins && chmod -R 777 /var/www/lmce-admin/skins/android

	*Note that this method will only get the android skins to save on bandwidth.		*Note that this method will only get the android skins to save on bandwidth.

Golgoj4: /* Configuration */

2013-08-16T02:53:13Z

Configuration

←Older revision		Revision as of 02:53, 16 August 2013
Line 19:		Line 19:

	sudo apt-get install subversion		sudo apt-get install subversion
	svn co http://svn.linuxmce.org/svn/trunk/src/qOrbiter/qOrbiter_src/qml/android/* /var/www/lmce-admin/skins/~~android~~		svn co http://svn.linuxmce.org/svn/trunk/src/qOrbiter/qOrbiter_src/qml/android/ /var/www/lmce-admin/skins/

	*Note that this method will only get the android skins to save on bandwidth.		*Note that this method will only get the android skins to save on bandwidth.

Golgoj4: /* Configuration */

2013-08-16T02:50:42Z

Configuration

←Older revision		Revision as of 02:50, 16 August 2013
Line 19:		Line 19:

	sudo apt-get install subversion		sudo apt-get install subversion
	svn co http://svn.linuxmce.org/svn/~~branches/LinuxMCE-1004~~/src/qOrbiter/qOrbiter_src/qml /var/www/lmce-admin/skins		svn co http://svn.linuxmce.org/svn/trunk/src/qOrbiter/qOrbiter_src/qml/android/* /var/www/lmce-admin/skins/android

			*Note that this method will only get the android skins to save on bandwidth.

	Now your skins are installed.		Now your skins are installed.

Marie.o: Remove qOrbiterGenerator.php requirement.

2013-03-26T17:05:42Z

Remove qOrbiterGenerator.php requirement.

←Older revision		Revision as of 17:05, 26 March 2013
Line 11:		Line 11:
	*When the core is ready, it will ask you to do a quick reload. MAKE SURE to set the default user and location.		*When the core is ready, it will ask you to do a quick reload. MAKE SURE to set the default user and location.
	*Quick Reload the router when asked.		*Quick Reload the router when asked.
	~~'''~~*~~Generate the orbiter config by visiting this page http~~:~~//<you-core-address>/lmce-admin/~~qOrbiterGenerator.php~~?d=the-device-number'''~~		*Note: It is no longer needed to run qOrbiterGenerator.php.
	~~Example : http://192.168~~.~~80.1/lmce-admin/qOrbiterGenerator.php?d=84~~

	Now you will need to decide on a skin. Eventually, this will be a cleaner process. For the moment, it isnt :)		Now you will need to decide on a skin. Eventually, this will be a cleaner process. For the moment, it isnt :)

Marie.o: /* Configuration */

2012-10-24T17:36:46Z

Configuration

←Older revision		Revision as of 17:36, 24 October 2012
Line 15:		Line 15:

	Now you will need to decide on a skin. Eventually, this will be a cleaner process. For the moment, it isnt :)		Now you will need to decide on a skin. Eventually, this will be a cleaner process. For the moment, it isnt :)
	All skins live on the core and will be accessible from http://<~~your~~-~~route~~-ip>/lmce-admin/skins The following instructions are for the core machine.		All skins live on the core and will be accessible from http://<you-core-address>/lmce-admin/skins The following instructions are for the core machine.

	All skins need a skins directory:		All skins need a skins directory:

Marie.o: Copied Setup instructions from Android to a general page, so people have a chance to easily find the instructions.

2012-09-09T10:08:07Z

Copied Setup instructions from Android to a general page, so people have a chance to easily find the instructions.

New page

This page outlines what is needed to setup LinuxMCE to support a qOrbiter. These instructions are relevant for any qOrbiter running device. Some stuff only needs to be done ones (like the skin downloading), other stuff, like the creation of the Orbiter device, should be done for each qOrbiter device. Each qOrbiter-running hardware device should have a dedicated device ID.

==Configuration==
You will need to prepare for the addition of the device to your system before it can be used by following these steps.
*Navigate to the 'Orbiters' page in the LinuxMCE Admin website. Create a new QOrbiter device from the dropdown box at the bottom. Make sure you fill in all the information there like:
**User
**Room
**Size - This is a remnant of the old orbiter, choose the smallest one, so that any regen it does is fast.
**'''Make a note of the device number'''
*When done, choose update.
*When the core is ready, it will ask you to do a quick reload. MAKE SURE to set the default user and location.
*Quick Reload the router when asked.
'''*Generate the orbiter config by visiting this page http://<you-core-address>/lmce-admin/qOrbiterGenerator.php?d=the-device-number'''
Example : http://192.168.80.1/lmce-admin/qOrbiterGenerator.php?d=84

Now you will need to decide on a skin. Eventually, this will be a cleaner process. For the moment, it isnt :)
All skins live on the core and will be accessible from http://<your-route-ip>/lmce-admin/skins The following instructions are for the core machine.

All skins need a skins directory:

sudo apt-get install subversion
svn co http://svn.linuxmce.org/svn/branches/LinuxMCE-1004/src/qOrbiter/qOrbiter_src/qml /var/www/lmce-admin/skins

Now your skins are installed.

==Running the device==
*Assuming the previous steps were completed, you can now connect.
*The default ip it connects to is 192.168.80.1
*Enter the device number you previously made note of for the device number
*If your core address is not standard, it will hang. you can kill the device and edit the config.xml at the location listed below.

The configuration file is located on the SDCard under /LinuxMCE (for Android

==Remote Access==

In order to use qOrbiter from outside your internal LinuxMCE network, you need to:
*Open ports 2757 & 3450 on your firewall via webadmin
*Change the host line in LinuxMCE/config.xml on your device to your core's external IP address.

[[Category:Programmer's Guide]][[Category:QML]][[category:QOrbiter]]