Status - Revision history

Wierdbeard65 at 07:19, 3 May 2010

2010-05-03T07:19:26Z

←Older revision		Revision as of 07:19, 3 May 2010
Line 1:		Line 1:
			{{Versioninfo}}
	[[Category: Admin Website]]		[[Category: Admin Website]]
	[[Category: Security]]		[[Category: Security]]

Rwilson131: Added Screenshots

2007-11-22T21:37:58Z

Added Screenshots

←Older revision		Revision as of 21:37, 22 November 2007
Line 1:		Line 1:
	~~<p>~~This allows you to manually set the individual sensors in your home. You can change the mode for that sensor independently. For example, instead of arming the whole house, you can arm just a few sensors. You can also change the 'Bypass' setting for each sensor. 'Normal' means the sensor is not bypassed. 'Wait' means the sensor is waiting however many seconds you specified in the 'Wait before alarm' setting before becoming active. It will return to 'Normal' after that many seconds. 'Bypass' means you have bypassed this sensor this one time. As soon as someone enters the PIN code on Orbiter the sensor will not be bypassed anymore. 'Perm bypass' means the sensor is bypassed and will stay bypassed until you change it again here on this page.~~</p>~~		[[Category: Admin Website]]
	~~<p>~~If you want to permanently disable a certain sensor, you could go to the Wizard/Security/Respond to Sensors page and change that sensor to "Do nothing". That allows you to disable the sensor for only certain modes (like armed or sleeping). Or you can set it to "Perm bypass" on this page. That means the sensor is permanently bypassed for all modes no matter what you put on the Respond to Sensors page.~~</p>~~		[[Category: Security]]
			[[Image:SecurityStatus.jpg\|thumb\|200px\|Security Status Admin Page]]
			This allows you to manually set the individual sensors in your home. You can change the mode for that sensor independently. For example, instead of arming the whole house, you can arm just a few sensors. You can also change the 'Bypass' setting for each sensor. 'Normal' means the sensor is not bypassed. 'Wait' means the sensor is waiting however many seconds you specified in the 'Wait before alarm' setting before becoming active. It will return to 'Normal' after that many seconds. 'Bypass' means you have bypassed this sensor this one time. As soon as someone enters the PIN code on Orbiter the sensor will not be bypassed anymore. 'Perm bypass' means the sensor is bypassed and will stay bypassed until you change it again here on this page.

			If you want to permanently disable a certain sensor, you could go to the Wizard/Security/Respond to Sensors page and change that sensor to "Do nothing". That allows you to disable the sensor for only certain modes (like armed or sleeping). Or you can set it to "Perm bypass" on this page. That means the sensor is permanently bypassed for all modes no matter what you put on the Respond to Sensors page.

Jerry finn at 14:52, 16 March 2007

2007-03-16T14:52:07Z

←Older revision		Revision as of 14:52, 16 March 2007
Line 1:		Line 1:
	<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table><p>This allows you to manually set the individual sensors in your home. You can change the mode for that sensor independently. For example, instead of arming the whole house, you can arm just a few sensors. You can also change the 'Bypass' setting for each sensor. 'Normal' means the sensor is not bypassed. 'Wait' means the sensor is waiting however many seconds you specified in the 'Wait before alarm' setting before becoming active. It will return to 'Normal' after that many seconds. 'Bypass' means you have bypassed this sensor this one time. As soon as someone enters the PIN code on Orbiter the sensor will not be bypassed anymore. 'Perm bypass' means the sensor is bypassed and will stay bypassed until you change it again here on this page.</p>		<p>This allows you to manually set the individual sensors in your home. You can change the mode for that sensor independently. For example, instead of arming the whole house, you can arm just a few sensors. You can also change the 'Bypass' setting for each sensor. 'Normal' means the sensor is not bypassed. 'Wait' means the sensor is waiting however many seconds you specified in the 'Wait before alarm' setting before becoming active. It will return to 'Normal' after that many seconds. 'Bypass' means you have bypassed this sensor this one time. As soon as someone enters the PIN code on Orbiter the sensor will not be bypassed anymore. 'Perm bypass' means the sensor is bypassed and will stay bypassed until you change it again here on this page.</p>
	<p>If you want to permanently disable a certain sensor, you could go to the Wizard/Security/Respond to Sensors page and change that sensor to "Do nothing". That allows you to disable the sensor for only certain modes (like armed or sleeping). Or you can set it to "Perm bypass" on this page. That means the sensor is permanently bypassed for all modes no matter what you put on the Respond to Sensors page.</p>		<p>If you want to permanently disable a certain sensor, you could go to the Wizard/Security/Respond to Sensors page and change that sensor to "Do nothing". That allows you to disable the sensor for only certain modes (like armed or sleeping). Or you can set it to "Perm bypass" on this page. That means the sensor is permanently bypassed for all modes no matter what you put on the Respond to Sensors page.</p>

Wikiadmin: Imported document

2006-06-05T16:46:00Z

Imported document

New page

<table width="100%"> <tr><td bgcolor="#FFCFCF">This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto.</td></tr> </table><p>This allows you to manually set the individual sensors in your home. You can change the mode for that sensor independently. For example, instead of arming the whole house, you can arm just a few sensors. You can also change the 'Bypass' setting for each sensor. 'Normal' means the sensor is not bypassed. 'Wait' means the sensor is waiting however many seconds you specified in the 'Wait before alarm' setting before becoming active. It will return to 'Normal' after that many seconds. 'Bypass' means you have bypassed this sensor this one time. As soon as someone enters the PIN code on Orbiter the sensor will not be bypassed anymore. 'Perm bypass' means the sensor is bypassed and will stay bypassed until you change it again here on this page.</p>
<p>If you want to permanently disable a certain sensor, you could go to the Wizard/Security/Respond to Sensors page and change that sensor to "Do nothing". That allows you to disable the sensor for only certain modes (like armed or sleeping). Or you can set it to "Perm bypass" on this page. That means the sensor is permanently bypassed for all modes no matter what you put on the Respond to Sensors page.</p>