Difference between revisions of "Express Controls EZmotion (HSM 100)"
m |
|||
| Line 14: | Line 14: | ||
* Light sensor | * Light sensor | ||
* Temperature sensor. | * Temperature sensor. | ||
| + | |||
| + | = Setup = | ||
| + | If you use SIS mode in your ZWave setup, this device should automatically be added as three multilevel sensors. | ||
| + | If not, it is possible to set it up manually. If you are running SIS mode, you can delete the main device and re-add it as a motion detector, see below for details. | ||
| + | |||
| + | You will have one multilevel sensor added for the EZMotion. Find and open this from the device tree. | ||
| + | We will change this to be the thermometer instance. | ||
| + | Change the Port/Channel number to 4/3, type to Thermometer, insert 49 in Capabilities, and save. | ||
| + | |||
| + | Add a new device below the ZWave Embedded Climate Interface using the same device template (Multilevel sensor). | ||
| + | Insert 4/2 in Port/Channel number, insert 49 in Capabilities and save. | ||
| + | This will be the brightness sensor. Please notice that the values returned from this sensor ranges from 0 to 100% and is relative to the light measured since X (see the manual). | ||
| + | |||
| + | Then we add the Motion detector. This will not be added automatically even when running the SIS mode. | ||
| + | Open the ZWave Embedded Security Interface and click Create New Child. Select the Motion Detector template. | ||
| + | Insert 4 in Port/Channel number, Motion Detector in type, 133,96,49,112,132,128,114,119,134 in Capabilities, and save. | ||
| + | |||
| + | Reload router and you should receive events from all three sensors. | ||
| + | |||
= Command classes = | = Command classes = | ||
Revision as of 20:05, 2 March 2010
Contents
Status
Received sample from dianemo.co.uk (those guys rock)
About
The EZMotion is a 3-in-1 Z-Wave sensor. This is also sold by Innovus and Homeseer (HSM100)
Manuf ID1: 0x0 ID2: 0x1e, Prod Typ1: 0x0 Typ2: 0x2, Prod ID1: 0x0 ID2: 0x1
Features
- Motion detection
- Light sensor
- Temperature sensor.
Setup
If you use SIS mode in your ZWave setup, this device should automatically be added as three multilevel sensors. If not, it is possible to set it up manually. If you are running SIS mode, you can delete the main device and re-add it as a motion detector, see below for details.
You will have one multilevel sensor added for the EZMotion. Find and open this from the device tree. We will change this to be the thermometer instance. Change the Port/Channel number to 4/3, type to Thermometer, insert 49 in Capabilities, and save.
Add a new device below the ZWave Embedded Climate Interface using the same device template (Multilevel sensor). Insert 4/2 in Port/Channel number, insert 49 in Capabilities and save. This will be the brightness sensor. Please notice that the values returned from this sensor ranges from 0 to 100% and is relative to the light measured since X (see the manual).
Then we add the Motion detector. This will not be added automatically even when running the SIS mode. Open the ZWave Embedded Security Interface and click Create New Child. Select the Motion Detector template. Insert 4 in Port/Channel number, Motion Detector in type, 133,96,49,112,132,128,114,119,134 in Capabilities, and save.
Reload router and you should receive events from all three sensors.
Command classes
0x4 0x21 0x1
- COMMAND_CLASS_MULTI_INSTANCE
- COMMAND_CLASS_SENSOR_MULTILEVEL
- COMMAND_CLASS_CONFIGURATION
- COMMAND_CLASS_WAKE_UP
- COMMAND_CLASS_ASSOCIATION
- COMMAND_CLASS_BATTERY
- COMMAND_CLASS_MANUFACTURER_SPECIFIC
- COMMAND_CLASS_NODE_NAMING
- COMMAND_CLASS_VERSION
