Difference between revisions of "Leadtek DTV2000H"
m |
|||
| (4 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
[[Category: Hardware]] | [[Category: Hardware]] | ||
| + | {{versioninfo}} | ||
[[Category: Video]] | [[Category: Video]] | ||
[[Category: TV Cards]] | [[Category: TV Cards]] | ||
| − | |||
'''Chipset''' | '''Chipset''' | ||
| Line 74: | Line 74: | ||
+ if ((core->board) == CX88_BOARD_WINFAST_DTV2000H_2) cx_write(MO_GP0_IO, 0x00017300);/*switch signal input to antena*/ | + if ((core->board) == CX88_BOARD_WINFAST_DTV2000H_2) cx_write(MO_GP0_IO, 0x00017300);/*switch signal input to antena*/ | ||
gives an error (invalid binary assignment) | gives an error (invalid binary assignment) | ||
| + | |||
| + | |||
| + | I succeeded in getting the patched code to compile by changing: | ||
| + | + if ((core->board) | ||
| + | to | ||
| + | + if ((core->boardnr) | ||
| + | but it still only gives me analog tv without sound | ||
| + | |||
Anyway, to get the digital tuner to work you will need to follow 3 simple steps: | Anyway, to get the digital tuner to work you will need to follow 3 simple steps: | ||
Latest revision as of 17:02, 29 September 2010
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | Unknown | N/A | N/A |
| 810 | Unknown | N/A | N/A |
| 1004 | Unknown | N/A | N/A |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
Chipset
Conexant CX23881 + Conexant CX22702
Tuner
Philips FMD1216
Hardware Interface
32-bit PCI 2.3 bus mastering Plug-n-Play compliant
Graphics drivers must include DirectX 8.1 software Video Standards
TV Tuner Receiving Frequency range from 48.25 to 863.25 MHz
FM radio band coverage from 87.50 MHz to 108.00 MHz
Connectors (version I or previous version)
FM RF in connector (75 Ohm)
TV RF in connector for Antenna (analog or digital TV signal)
TV RF in connector for Cable (analog TV signal)
1 phone jack for remote sensor
1 phone jack for audio input
1 6-pin MiniDin for CVBS and S-Video input
1 4-pin audio output connector
Connectors (version J)
FM RF in connector (75 Ohm)
TV RF in connector for Antenna (analog or digital TV signal)
TV RF in connector for Cable (analog TV signal)
1 phone jack for remote sensor
1 9-pin MiniDin CVBS, S-Video and audio input
1 4-pin audio output connector
There are 2 versions of this card, version 'I' & version 'J'. According various forums, version 'I' works out of the box, yet the later version 'J' needs some tinkering. Apparently version J was made to be compatible with Vista, so if you can avoid the box thats says Vista ready!
Version J Setup
Although this card does not work out of the box with a little tinkering you can quite easily get the Digital tuner to work in LinuxMCE. There is a patch available to get both the analogue and digital tuners but it looked a little too complex for my liking. http://lkml.org/lkml/2008/2/6/289 This patch is broken with kernel 2.6.25 diff -Naur /usr/src/linux/drivers/media/video/cx88/cx88-mpeg.c /usr/src/linux/drivers/media/video/cx88-patched/cx88-mpeg.c --- /usr/src/linux/drivers/media/video/cx88/cx88-mpeg.c 2007-10-09 22:31:38.000000000 +0200 +++ /usr/src/linux/drivers/media/video/cx88-patched/cx88-mpeg.c 2008-01-07 23:28:29.000000000 +0100 @@ -93,6 +93,7 @@
/* FIXME: this needs a review. * also: move to cx88-blackbird + cx88-dvb source files? */
+ if ((core->board) == CX88_BOARD_WINFAST_DTV2000H_2) cx_write(MO_GP0_IO, 0x00017300);/*switch signal input to antena*/ gives an error (invalid binary assignment)
I succeeded in getting the patched code to compile by changing:
+ if ((core->board)
to
+ if ((core->boardnr)
but it still only gives me analog tv without sound
Anyway, to get the digital tuner to work you will need to follow 3 simple steps:
1. Configure linux to load the module cx88-dvb automatically on start-up using the command: sudo echo "cx88-dvb" >> /etc/modules
This will add the line cx88-dvb to the file /etc/modules.
2. Edit the /etc/modprobe.d/options file and add the line:
options cx88xx card=51
(card number 51 has been allocated to a different card recently, not sure if it is official but 68 was mentioned somewhere as appropriate)
This will tell mythtv exactly what type of card you are using.
3. In Mythtv-setup, under capture cards, select 'DVB DTV capture card (v3.x)' for the card type. Set 'DVB Card Number' to 0 ( for the first card, 1 for 2nd card etc)
Remote Control
Not tested. Add your experiences here.
