Difference between revisions of "TDM400P"
(New page: Installing Everything you Need: ''apt-get install zaptel apt-get install zaptel-source m-a a-i zaptel genzaptelconf -sdvM'' Edit Needed Configs: ''nano /etc/asterisk/zapata.conf'' for ...) |
(→Add a Trunk for every FXO module) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | Installing Everything you Need | + | ==Installing Everything you Need== |
| − | ''apt-get install zaptel | + | ''apt-get install zaptel'' |
| − | + | ||
| − | + | ||
| − | + | ||
| − | Edit Needed Configs | + | ''apt-get install zaptel-source'' |
| + | |||
| + | ''m-a a-i zaptel'' | ||
| + | |||
| + | ''genzaptelconf -sdvM'' | ||
| + | |||
| + | ===Edit Needed Configs=== | ||
''nano /etc/asterisk/zapata.conf'' | ''nano /etc/asterisk/zapata.conf'' | ||
| Line 13: | Line 16: | ||
''context=from-internal'' | ''context=from-internal'' | ||
| + | |||
''signalling=fxo_ks # use the correct signalling'' | ''signalling=fxo_ks # use the correct signalling'' | ||
| + | |||
''channel => 1 # use the correct zaptel channel/port, ranges are possible as well'' | ''channel => 1 # use the correct zaptel channel/port, ranges are possible as well'' | ||
| Line 19: | Line 24: | ||
''context=from-pstn'' | ''context=from-pstn'' | ||
| + | |||
''signalling=fxs_ks # use the correct signalling'' | ''signalling=fxs_ks # use the correct signalling'' | ||
| + | |||
''channel => 1 # use the correct zaptel channel/port, ranges are possible as well'' | ''channel => 1 # use the correct zaptel channel/port, ranges are possible as well'' | ||
| − | Now get into the AMP Configuration | + | ===Now get into the AMP Configuration=== |
''Web Admin -> Phone Lines -> Deactivate Automatic Configuration -> To Configure AMP, click click here'' | ''Web Admin -> Phone Lines -> Deactivate Automatic Configuration -> To Configure AMP, click click here'' | ||
| Line 29: | Line 36: | ||
''Click on Trunks -> Add ZAP Trunk'' | ''Click on Trunks -> Add ZAP Trunk'' | ||
| + | |||
''Maximum channels: 1'' | ''Maximum channels: 1'' | ||
| + | |||
''Zap Identifier (trunk name): <Use the channel number for the FXO port that you created in zapata.conf>'' | ''Zap Identifier (trunk name): <Use the channel number for the FXO port that you created in zapata.conf>'' | ||
| + | |||
''Submit Changes'' | ''Submit Changes'' | ||
| Line 45: | Line 55: | ||
Setup FXS Extension for every FXS module: | Setup FXS Extension for every FXS module: | ||
''Click on Extension''. | ''Click on Extension''. | ||
| + | |||
''Device: Select "Generic ZAP Device"'' | ''Device: Select "Generic ZAP Device"'' | ||
| + | |||
''Submit'' | ''Submit'' | ||
| + | |||
''User Extension: <put in a number, I started at 300>'' | ''User Extension: <put in a number, I started at 300>'' | ||
| + | |||
''Display Name: <put in a name>'' | ''Display Name: <put in a name>'' | ||
| + | |||
''This device uses zap technology.'' | ''This device uses zap technology.'' | ||
| + | |||
''channel <Put in the FXS Port number>'' | ''channel <Put in the FXS Port number>'' | ||
| + | |||
''Submit'' | ''Submit'' | ||
Now this is a VERY VERY basic setup designed to just get it to work. You will still have to fine tune your FXO ports. I will setup a page for that wants I get mine done. | Now this is a VERY VERY basic setup designed to just get it to work. You will still have to fine tune your FXO ports. I will setup a page for that wants I get mine done. | ||
Latest revision as of 10:17, 5 February 2011
Installing Everything you Need
apt-get install zaptel
apt-get install zaptel-source
m-a a-i zaptel
genzaptelconf -sdvM
Edit Needed Configs
nano /etc/asterisk/zapata.conf
for FXS Ports:
context=from-internal
signalling=fxo_ks # use the correct signalling
channel => 1 # use the correct zaptel channel/port, ranges are possible as well
for FXO Ports:
context=from-pstn
signalling=fxs_ks # use the correct signalling
channel => 1 # use the correct zaptel channel/port, ranges are possible as well
Now get into the AMP Configuration
Web Admin -> Phone Lines -> Deactivate Automatic Configuration -> To Configure AMP, click click here
Add a Trunk for every FXO module.
Click on Trunks -> Add ZAP Trunk
Maximum channels: 1
Zap Identifier (trunk name): <Use the channel number for the FXO port that you created in zapata.conf>
Submit Changes
Add an Inbound Route.
Leave everything blank except for "Set Destination", I setup a Ring Group and selected that. Submit Changes
Now setup your Outbound Route(s), Most likely one per FXO port. I edited the existing route. Setup what ever Dial Patterns you want, I setup "9.|" for one port and "8|." for another port. Setup your Trunk Sequence Submit Changes
Setup FXS Extension for every FXS module: Click on Extension.
Device: Select "Generic ZAP Device"
Submit
User Extension: <put in a number, I started at 300>
Display Name: <put in a name>
This device uses zap technology.
channel <Put in the FXS Port number>
Submit
Now this is a VERY VERY basic setup designed to just get it to work. You will still have to fine tune your FXO ports. I will setup a page for that wants I get mine done.
