Difference between revisions of "Tricklestar 200ZW-EU-W"
From LinuxMCE
m (→Status) |
m |
||
| (9 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
[[Category: Hardware]] | [[Category: Hardware]] | ||
| + | {{versioninfo|710Status=According to category, Works without caveats|710UpdatedDate=11th May 2010|710UpdatedBy=[[User:Wierdbeard65|Wierdbeard65]]|810Status=According to category, Works without caveats|810UpdatedDate=11th May 2010|810UpdatedBy=[[User:Wierdbeard65|Wierdbeard65]]|}} | ||
[[Category: RF Control]] | [[Category: RF Control]] | ||
[[Category: ZWave]] | [[Category: ZWave]] | ||
| − | + | [[Category: ZWave_remote]] | |
| + | [[Category: Works without caveats on 0710]] | ||
| + | [[Category: Works without caveats on 0810]] | ||
[[Image:200ZW-XX-W-ii-(HI-RES).jpg|thumb|200px|Tricklestar 200ZW-EU-W]] | [[Image:200ZW-XX-W-ii-(HI-RES).jpg|thumb|200px|Tricklestar 200ZW-EU-W]] | ||
= Status = | = Status = | ||
Tested with the latest svn Z-Wave driver (will be included in 0810). Also works as inclusion controller when LinuxMCE runs as SIS. | Tested with the latest svn Z-Wave driver (will be included in 0810). Also works as inclusion controller when LinuxMCE runs as SIS. | ||
| − | Runs fine | + | Runs also fine with stock 0710 as primary or secondary controller. |
| − | '''This is | + | '''This is a recommended inclusion controller''' |
= About = | = About = | ||
The Tricklestar 200ZW-EU-W is a Z-Wave Remote Controller based on a Zensys chip. It uses a frequency of 868MHz. There is also a US version. | The Tricklestar 200ZW-EU-W is a Z-Wave Remote Controller based on a Zensys chip. It uses a frequency of 868MHz. There is also a US version. | ||
| + | |||
| + | = Configuration Switch = | ||
| + | The product has a slide switch under the Rubber end piece (next to the USB connector), which can set the product in “Operation Mode” and “Configuration Mode”. | ||
| + | |||
| + | = How to reset the Remote (from the Manual) = | ||
| + | |||
| + | Resetting the Controller | ||
| + | # Put the Configuration Switch in “Configuration Mode”. | ||
| + | # Press-and-hold “Up” Operation button for 2 seconds to enter Configuration Mode. LED Indicator will illuminate Green. | ||
| + | # Press-and-hold “Up” Operation button for 10 seconds - this will initiate a reset of the Controller. LED Indicator will alternate Red, Yellow and Green while remote is being reset. | ||
| + | # LED Indicator on the Remote will illuminate Green when Reset is successfully completed and illuminate Red if the operation is unsuccessful. | ||
= Links = | = Links = | ||
http://www.tricklestar.com | http://www.tricklestar.com | ||
Latest revision as of 07:34, 27 September 2012
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | According to category, Works without caveats | 11th May 2010 | Wierdbeard65 |
| 810 | According to category, Works without caveats | 11th May 2010 | Wierdbeard65 |
| 1004 | Unknown | N/A | N/A |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
.jpg)
Contents
Status
Tested with the latest svn Z-Wave driver (will be included in 0810). Also works as inclusion controller when LinuxMCE runs as SIS. Runs also fine with stock 0710 as primary or secondary controller.
This is a recommended inclusion controller
About
The Tricklestar 200ZW-EU-W is a Z-Wave Remote Controller based on a Zensys chip. It uses a frequency of 868MHz. There is also a US version.
Configuration Switch
The product has a slide switch under the Rubber end piece (next to the USB connector), which can set the product in “Operation Mode” and “Configuration Mode”.
How to reset the Remote (from the Manual)
Resetting the Controller
- Put the Configuration Switch in “Configuration Mode”.
- Press-and-hold “Up” Operation button for 2 seconds to enter Configuration Mode. LED Indicator will illuminate Green.
- Press-and-hold “Up” Operation button for 10 seconds - this will initiate a reset of the Controller. LED Indicator will alternate Red, Yellow and Green while remote is being reset.
- LED Indicator on the Remote will illuminate Green when Reset is successfully completed and illuminate Red if the operation is unsuccessful.
