Difference between revisions of "Seluxit viaSENS Home Controller"

From LinuxMCE
Jump to: navigation, search
(Setup)
 
(9 intermediate revisions by 6 users not shown)
Line 1: Line 1:
 
[[Category: Hardware]]
 
[[Category: Hardware]]
 +
[[Category: Automation]]
 
[[Category: RF Control]]
 
[[Category: RF Control]]
 
[[Category: ZWave]]
 
[[Category: ZWave]]
 +
[[Category: ZWave_controller]]
  
 +
{{versioninfo|810Status=PnP|810UpdatedDate=12th May 2010|810UpdatedBy=sambuca}}
 
[[Image:VSHomeController.jpg|thumb|200px|Seluxit viaSENS Homecontroller]]
 
[[Image:VSHomeController.jpg|thumb|200px|Seluxit viaSENS Homecontroller]]
  
Line 12: Line 15:
 
= About =  
 
= About =  
 
The Seluxit viaSENS Homecontroller is a USB Z-Wave Controller based on a Zensys chip. It uses a frequency of 868MHz.
 
The Seluxit viaSENS Homecontroller is a USB Z-Wave Controller based on a Zensys chip. It uses a frequency of 868MHz.
 +
 +
= Setup =
 +
To setup this device using SIS mode, send it a Reset command. In the web admin, go to Advanced -> Devices, find the ZWave device in the tree, select it, click "Send Command To Device" in the right pane. Select "Reset", enter "ResetController" in the Arguments field, and click Send Command. Note: This will delete all ZWave devices from your network.
 +
Now the device will get node id 1, and SIS mode is enabled, which means that LMCE assigns new node ids to added nodes.
 +
 +
New nodes(Z-Wave devices) can be added by sending the ZWave device a "Add Node" command. Follow the description above, only use Add Node instead of Reset. No parameters are necessary, but you could try using H for high power if you have problems adding a node.
  
 
= USB =
 
= USB =
Line 18: Line 27:
  
 
= Links =
 
= Links =
http://www.seluxit.com/VS_Controllers.html
+
http://www.seluxit.com/products/devices/
 +
http://www.hightechpad.com/?q=content/seluxit-z-wave-usb-controller

Latest revision as of 21:51, 25 April 2014


Version Status Date Updated Updated By
710 Unknown N/A N/A
810 PnP 12th May 2010 sambuca
1004 Unknown N/A N/A
1204 Unknown N/A N/A
1404 Unknown N/A N/A
Usage Information
Seluxit viaSENS Homecontroller

Status

Received sample from manufacturer. Plug and play with versions >= 0710b4.

This is the _recommended_ interface for Europe.

About

The Seluxit viaSENS Homecontroller is a USB Z-Wave Controller based on a Zensys chip. It uses a frequency of 868MHz.

Setup

To setup this device using SIS mode, send it a Reset command. In the web admin, go to Advanced -> Devices, find the ZWave device in the tree, select it, click "Send Command To Device" in the right pane. Select "Reset", enter "ResetController" in the Arguments field, and click Send Command. Note: This will delete all ZWave devices from your network. Now the device will get node id 1, and SIS mode is enabled, which means that LMCE assigns new node ids to added nodes.

New nodes(Z-Wave devices) can be added by sending the ZWave device a "Add Node" command. Follow the description above, only use Add Node instead of Reset. No parameters are necessary, but you could try using H for high power if you have problems adding a node.

USB

ID: 16c0:06eb Driver: cdc_acm

Links

http://www.seluxit.com/products/devices/ http://www.hightechpad.com/?q=content/seluxit-z-wave-usb-controller