Insteon PLM Ruby Code 373

Version	Status	Date Updated	Updated By
710	Unknown	N/A	N/A
810	Unknown	N/A	N/A
1004	Unknown	N/A	N/A
1204	Unknown	N/A	N/A
1404	Unknown	N/A	N/A
Usage Information

#### Written by Dan Damron
#### #373 Private Method Listing ####

def mainStart() ## This is called FIRST, reruns cannot call this.
#Register Message Interceptor
@interceptor = Command.new(device_.devid_, -1000, 1, 5, 37)
@interceptor.params_[2] = device_.devid_.to_s
SendCommand(@interceptor)

#Get the PLM Database
sendGetLink
#get Child devices
log('Finding Children..')
device_.childdevices_.each{|c|
if device_.childdevices_[c.to_s.to_i].devdata_[12].include? "Group"
log('FOUND A GROUP')
else
$children[device_.childdevices_[c.to_s.to_i].devdata_[12].chomp.lstrip.rstrip] = c.to_s.to_i
end}
$children.keys.each{|c| log(c + ' = ' + $children[c].to_s)
}
log('reading stored Child configuration:')

$children.keys.each{|c|
#Get each Childs configuration
$state[$children[c]] = 0
getdeviceconfig(c) #

#the above getdeviceconfig packs $configparams array
log('Configuration for ' + c + ' = ' + $configparams.inspect.to_s)
}

log('********************************************************')
#get childs actual configuation and status
$children.keys.each{|c| sendGetChildStatus(c)}
SndIns()

end
def mainRestart()
#We have hashes already set up.
$childdatabases.each_key{|@insteonID|
$state[$children[@insteonID]] = 0
sendGetChildStatus(@insteonID)}
SndIns()
end

def setdeviceconfig(insteonid, configurestring)
@deviceid = $children[insteonid]
@cmdfrom = device_.devid_
@cmdto = 4 #general info plugin
@priority = 1
@type=1 #command
@cmdid = 246

#set up command..
@cmd = Command.new(@cmdfrom, @cmdto, @priority, @type, @cmdid)
@cmd.params_[2] = @deviceid.to_s
@cmd.params_[52] = '59' # Configuration
@cmd.params_[5] = configurestring
SendCommand(@cmd)
log('SetDeviceConfig:' + @cmd.to_s)
#log('SetDeviceConfig:' + configurestring)
#log('Configuration Saved - will be available on next reload')
end

def getdeviceconfig(insteonid)
@deviceid = $children[insteonid]
@configstring = ''
begin
@configstring = device_.childdevices_[@deviceid].devdata_[59].to_s
rescue
log('Device ID = ' + @deviceid.to_s)
log($red + 'Error - Child has no configuration'+ $grey)
log('Setting initial value of "****************"')
setdeviceconfig(insteonid, ('*' * 16))
@configstring = '*' * 16
sendPing(insteonid)
end
if @configstring == ''
$configparams = ['****************']
log('CAUGHT BLANK RECORD')
setdeviceconfig(insteonid, ('*' * 16))
sendPing(insteonid)
else
$configparams = @configstring.unpack('a16' * (@configstring.length / 16))
$devicetemplate[insteonid] = getdevicetemplate($configparams[0][0..1], $configparams[0][2..3])
end
#log($yellow + 'getdeviceconfig:' + $configparams.inspect + $grey)
#add the configuration parameters to the child database
$childdatabases[insteonid] = $configparams
#get the device type

end

def sendGetLink()
#lets just see exactly what is in the PLM database
param = {'Command' => 'GetLnk'}
$cmdqueue << param
SndIns()
end

def sendGetNext()
param = {'Command' => 'GetNext'}
if $wAIT == true
$cmdqueue.insert(1, param)
else
$cmdqueue.insert(0,param)
end
SndIns()
end

def sendRemoteGetLink(insteonID)
# Read First ALDB Record
# a few variables need to be set up here..
$recordof = insteonID # save the insteon ID
insID = insteonID.chomp.split('.') # get the seperate bytes
$remoteDBOffsetMSB = 0x0F # initial offset
$remoteDBOffsetLSB = 0xF8 # initial LSB offset
param = {'Command' => 'SndIns',
'Parameter1' => insID[0], #HB
'Parameter2' => insID[1], #MB
'Parameter3' => insID[2], #LB
'Parameter4' => '0F', #Flags
'Parameter5' => '28', #Cmd1
'Parameter6' => "%X" %$remoteDBOffsetMSB #Cmd2 Set MSB Offset
}
$cmdqueue << param
# repeat last param for each byte to read (F8..FF)=first record

for x in 0..7
param = {'Command' => 'SndIns',
'Parameter1' => insID[0], #HB
'Parameter2' => insID[1], #MB
'Parameter3' => insID[2], #LB
'Parameter4' => '0F', #Flags
'Parameter5' => '2B', #Cmd1 Peek
'Parameter6' => "%X" %($remoteDBOffsetLSB + x) #Cmd2
}

$cmdqueue << param
end

end

def sendRemoteGetNext(insteonID)
insID = insteonID.chomp.split('.') # get the seperate bytes
### Do NOT forget to check to see if we need to decrease the MSB

if $remoteDBOffsetLSB == 0x00
#OffsetMSB needs to be decreased, and LSB needs reset.
$remoteDBOffsetMSB = $remoteDBOffsetMSB - 1
$remoteDBOffsetLSN = 0xFF # the next line will decrease this by 8
end
# decrease DBOffsetLSB by 0x08
$remoteDBOffsetLSB = $remoteDBOffsetLSB - 0x08

for x in 0..7
param = {'Command' => 'SndIns',
'Parameter1' => insID[0], #HB
'Parameter2' => insID[1], #MB
'Parameter3' => insID[2], #LB
'Parameter4' => '0F', #Flags
'Parameter5' => '2B', #Cmd1 Peek
'Parameter6' => "%X" %($remoteDBOffsetLSB + x) #Cmd2
}
#log('sendRemoteGetNet:added to queue:' + param.inspect)
if $wAIT == true
$cmdqueue.insert(x + 1, param)
else
$cmdqueue.insert(x,param)
end


end
end

### Main command parsing routine is EZToDCE
def EZToDCE(param)
#param contains a hash of EZBridge command structure
#log($blue + 'Queue:' + $cmdqueue[0].inspect + $grey)
#log($blue + 'Param:' + param.inspect + $grey)
#log($blue + 'currentcmd:' + $currentcmd.to_s + $grey)
#checkWait(param)
case param['Response']
# Standard RESPONSES (to commands)
when 'GetRevision' # Special Response
log('-----|---------GetRevision:' + param['Parameter1'])

when 'GetLatLong' # Special Response
log('-----|---------GetLatLong: Lat=' + param['Lat'] + ', Long=' + param['Long'])

when 'SetLatLong'
if param['Parameter1'] == 'True' then
log('-----|---------SetLatLong: Ok')
else
log('-----X---------SetLatLong: FAILED!')
end
when 'SetPasswd'

when 'SetTimeZone'

when 'GetClock' # Special Response

when 'SetClock'

when 'SetNTPServer'

when 'Upgrade'

when 'NetCfg'

when 'Reset'
#Reset Response

cmdComplete
SndIns()
when 'LstTimers' # Special Response


when 'ClrTimers'

when 'AddTimer'

when 'GetTimer' # Special Response

when 'SetTimer'

when 'DelTimer'

when 'GetVersion' # Special Response

when 'SndGrp'

when 'SndIns' # response from SndIns
### BUG FOUND ### When the EZBridge receives a command from an EXTERNAL source
### ie not from this device, cmdqueue will be nil, and the code below
### fails. Have to check against that.
if $cmdqueue.length > 0
#First, check the response to make sure the command made it ok.
if param['Parameter9'].to_i == 6 #Ack received
#log('Sending to ProcessACK')
processACK(param)
else # NACK received - command failed.
log('Command NACKED')
end
else
#Response received for another device.
log('Response detected for a command that was not sent by me')
end
when 'SndX10'
log('Response detected for SndX10')
if param['Parameter5'].to_i == 6 #ack
log('X10 Command Successfull')

cmdComplete
SndIns()
else
log('X10 Command FAILED')
cmdComplete
SndIns()

end
when 'StLnk'

when 'CancelLnk'

when 'SetDev'

when 'RstPLM'
#Reset Response
$timeout = 1
cmdComplete
SndIns()

when 'GetLnk'
if param['Parameter3'].to_i == 6 #ack
log('GetLnk ACKED')
#if we get this, we should get a AllLink Record Response next
else
log('GetLnk NACKED')
# The PLM is BLANK
#have to add records to the PLM here.
cmdComplete
### FINISHED WITH GetLnk
checkChildRecordsinPLM()
SndIns()
end
when 'GetNext'
if param['Parameter3'].to_i == 6 #ack
log('sendGetNext ACKED')
#if we get this, we should get a AllLink Record Response next
else
log('sendGetNext NACKED')
#we get this when there are no more records
cmdComplete
#FINISHED with GetNext
# if we are here, we are in config mode
# so, next is to check to make sure the
# childrens insteon ID is in the PLM
checkChildRecordsinPLM()
# now, to make sure that all the records in the PLM are sensed as children

SndIns()
end

when 'SetCfg' # response from Setcfg command
if param['Parameter4'].to_i == 6 #ack
log('SetCfg Completed')
cmdComplete
SndIns()
else
log('SetCfg NACKED')
end
when 'GetLnkData'

when 'LEDON'

when 'LEDOFF'

when 'MngLnk'
if param['Parameter12'].to_i == 6
log('MngLnk => ACK')
else
log('MngLnk => NACK')
end
cmdComplete
SndIns()

when 'GetCfg' # Special Response

when 'LstMacros' # Special Response

when 'ClrMacros'

when 'AddMacro'

when 'GetMacro' # Special Response

when 'SetMacro'

when 'DelMacro'

when 'LstDevices' # Special Response

when 'ClrDevices'

when 'AddDevice'

when 'GetDevice' # Special Response

when 'SetDevice'

when 'DelDevice'

when 'LstZones'

when 'ClrZones'

when 'AddZone'

when 'GetZone'

when 'SetZone'

when 'DelZone'

when 'AddDevZone'

when 'DelDevZone'

# Response Messages
when 'InsExtMsg'

when 'InsStdMsg'
case $currentcmd # if this msg is part of a response, the Insteon Cmd1 will be saved here.
when 0x0
#log('REROUTING to processExternalCommand(param)')
processExternalCommand(param)
when 0x1 #Assign to Group
### This is a broadcast message sent
# from a PING command
# or from a StartLink...
log('Caught Assign to Group Message from Device')
### BUG HERE
#have to check flags to see if this is a broadcast message
log('Checking if this is a broadcast message')
log('Flags:' + param['Parameter9'])
if (param['Parameter9'].hex & 0x80) == 0x80
log('Message IS BROADCAST')
#recvComplete
processDeviceInfo(param)

# check to see if current cmd is for this broadcast..
log('Current Command:' + $cmdqueue[0]['Parameter5'])
if $cmdqueue[0]['Parameter5'] == '10'
#log('Clearing PING Command')
$currentcmd = 0
cmdComplete
SndIns()
else
log('CURRENT CMD IS NOT PING - NOT CLEARING')
end

else
log('Message is NOT Broadcast')
end
when 0x2 #Delete from Group
when 0x10 # PING
#this is where I catch the InsStdMsg for ping.
log('Caught PING Message from Device')
$currentcmd = 1

when 0x11 # ON
log('Caught Insteon ON from INTERNAL source')
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']

insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
log('Current DIM level:' + param['Parameter11'])

reportStatus(myDevFrom, hextopercent(param['Parameter11']))

$currentcmd = 0
cmdComplete

SndIns()
when 0x13 # OFF
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
reportStatus(myDevFrom, 0)

$currentcmd = 0
cmdComplete
#log('EVENT and state SENT!!!.48:[10]=0')
SndIns()
#####Thermostat Does Not report Status correctly Yet. Have to figure out reportStatus###
when 0x6A #Thermostat Control Get Zone Data (Temp, Setpoint,Humidity)
log('Thermostat returned Zone Info: ' + param['Parameter11'].to_s)
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#reportStatus(myDevFrom, hextopercent(param['Parameter11']))
$currentcmd = 0
cmdComplete
SndIns()

when 0x6B #Thermostat Control Command Handle Response
log('Thermostat returned: ' + param['Parameter11'].to_s)
case param['Parameter11'].to_s
when '06' # ON/Auto
# $ThermostatStatus = 'ON/Auto' ##not used
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 6)
$currentcmd = 0
cmdComplete
SndIns()

when '09' #OFF
# $ThermostatStatus = 'OFF' ## not used may be for reportstatus
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 9)
$currentcmd = 0
cmdComplete
SndIns()

when '04' # Heat
#$ThermostatStatus = 'HEAT'
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 4)
$currentcmd = 0
cmdComplete
SndIns()

when '05' # Cool
#$ThermostatStatus = 'COOL'
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 5)
$currentcmd = 0
cmdComplete
SndIns()


when '07' # Fan On
2#$ThermostatStatus = 'COOL'
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 5)
$currentcmd = 0
cmdComplete
SndIns()


when '08' # Fan Off
#$ThermostatStatus = 'COOL'
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
#log('Current Thermostat State:' + $ThermostatStatus)
#reportStatus(myDevFrom, 5)
$currentcmd = 0
cmdComplete
SndIns()
end


when 0x6C #Thermostat Control Get Zone Cool Point Data
log('Thermostat returned Zone Info: ' + param['Parameter11'].to_s)
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
log('Current Zone level:' + param['Parameter11'].to_s)
#reportStatus(myDevFrom, hextopercent(param['Parameter11']))
$currentcmd = 0
cmdComplete
SndIns()

when 0x6D #Thermostat Control Get Zone Heat Point Data
log('Thermostat returned Zone Info: ' + param['Parameter11'].to_s)
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
log('Current Zone level:' + param['Parameter11'].to_s)
#reportStatus(myDevFrom, hextopercent(param['Parameter11']))
$currentcmd = 0
cmdComplete
SndIns()


when 0x19 # Status Report
# now to clear the currentcmd and remove command from the queue
$currentcmd = 0
cmdComplete

log('Processing 0x19 Status Report')
#This is where I get the database delta (in cmd1)
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
#First, to compare the DB Delta with current config.
#Database Delta...
delta = param['Parameter10'].to_s
log($blue + 'Database Delta=' + delta + $grey)
log($blue + 'Configuration is:' + getdeltafromconfig(insID) + $grey)
if delta == getdeltafromconfig(insID)
if $children[insID] != nil
myDevFrom = $children[insID]
myDevTo = -1000 #DCE Router
myPriority = 1
myType = 2 #Event

#Send an EVENT to report STATE ONLY if database has not changed
# AND child exists in pluto
reportStatus(myDevFrom, hextopercent(param['Parameter11']))
end
else
log('Databse CHANGED -getting remote database')
#here, I have to WIPE the databse
# to prepare it for new data
### here is where the DAMN CONFIG was reset!!!
oldconfigstring = $childdatabases[insID][0]
$childdatabases[insID] = [oldconfigstring]
log('Setting Database Config')
$childdatabases[insID][0][6..7] = delta
savechilddatabases(insID)
sendRemoteGetLink(insID)
end
# finally, to check execute next command...
SndIns()
when 0x28 # Set Address MSB
log('Received SET Address MSB from remote device')
$currentcmd = 0
$remoteLinkRecord = ''
cmdComplete
SndIns()
when 0x2B # peek
### BUG HERE... have to verify response is a PEEK command
#response command is stored in parameter10
if param['Parameter10'].hex == 0x2B # this is the peek command
cmdComplete
log('Received PEEK from remote Device! DATA=' + param['Parameter11'])
checkPeekData(param)
$currentcmd = 0
SndIns()
else
log('Waiting for remote PEEK response, but got :' + param['Parameter10'])
end
else
end

when 'X10Msg'
log($purple + 'X10 Message Received' + $grey)
if param['Parameter4'].hex == 0x00
log('This byte is a House/Unit Code')
hn = param['Parameter3'][0].chr
ln = param['Parameter3'][1].chr
$x10byte1 = $X10HouseCodes[hn]
$x10byte1 += $X10UnitCodes[ln]
log('Translated X10 House/Unit Code:' + $x10byte1)
else
log('This byte is a House/Command Code')
hn = param['Parameter3'][0].chr
ln = param['Parameter3'][1].chr
$x10byte2 = $X10HouseCodes[hn]
$x10byte2 += $X10CommandCodes[ln]
log('Translated X10 Command Code:' + $x10byte2)
log('X10 Command ready to send:' + $x10byte1 + ' ' + $x10byte2)
case $X10CommandCodes[ln]
when 'On'
#Send ON to lmnce
if $children[$x10byte1] == nil
log('I do not control this X10 device')
else
cmd = Command.new($children[$x10byte1].to_i, -1000, 1, 1, 192)
cmd.params_[120] = "1"
SendCommand(cmd)
end
when 'Off'
#Send OFF to lmnce
if $children[$x10byte1] == nil
log('I do not control this X10 device')
else
cmd = Command.new($children[$x10byte1].to_i, -1000, 1, 1, 193)
cmd.params_[120] = "1"
SendCommand(cmd)
end
when 'Bright'
if $children[$x10byte1] == nil
log('I do not control this X10 device')
else
#send a command to set the state + 1
@curstate = ($state[$x10byte1] / 100) * 32 #get equal 32 steps
$state[$x10byte1] = ((@curstate + 1) / 32) * 100
cmd = Command.new($children[$x10byte1].to_i, -1000, 1, 1, 184)
cmd.params_[76] = $state[$x10byte1].to_s
cmd.params_[120] = "1"
SendCommand(cmd)
#$state[$x10byte1] = ($state[$x10byte1] / 100) * 32
end
when 'Dim'
@curstate = ($state[$x10byte1] / 100) * 32 #get equal 32 steps
$state[$x10byte1] = ((@curstate - 1) / 32) * 100
cmd = Command.new($children[$x10byte1].to_i, -1000, 1, 1, 184)
cmd.params_[76] = $state[$x10byte1].to_s
cmd.params_[120] = "1"
SendCommand(cmd)
when 'All Lights Off'
log('ALL Lights OFF Command not implemented')
when 'All Lights On'
log('All Lights ON Command not implemented')
when 'Status Request'
log('Status Request Command not implemented')
when 'Hail Ack'
log('Hail Ack Command not implemented')
end

end
when 'InsLnkSts'
log('InsLnkSts Received')

when 'BtnRpt'
log('Button Report Received')
when 'UsrRst'
log('User Reset Response Received')
when 'GrpEvntRpt'
log('Group Event Report Received')

when 'LnkData'
processLnkData(param)
# Other messages
when 'PLMTimeout'
log('PLM Timeout detected.. resetting EZBridge')
resetcmd = {'Command' => 'Reset'}
if $wAIT == true
$cmdqueue.insert(1, resetcmd)
else
$cmdqueue.insert(0,resetcmd)
end
sleep 15
$wAIT = false
SndIns()
when 'PLMEchoError' # Have not seen this since a1.23
# error sending command to PLM, reset command and try again
log('-----XXXXXXX' + param['Response'])
resetcmd = {'Command' => 'Reset'}
if $wAIT == true
$cmdqueue.insert(1, resetcmd)
else
$cmdqueue.insert(0,resetcmd)
end

sleep 15
$wAIT = false
SndIns()
when 'LongAck'
log('-----XXXXXXX' + param['Response'])
# Error - seems to show up after PLMEchoError
resetcmd = {'Command' => 'Reset'}
if $wAIT == true
$cmdqueue.insert(1, resetcmd)
else
$cmdqueue.insert(0,resetcmd)
end
sleep 15
$wAIT = false
SndIns()
else
log('-----XXXXXXX UNKNOWN Response Received')
end

end

### Support routine for EZToDCE
def processLnkData(param)
#Caught a LnkData Response
log('LnkData Message Received')
log(param.inspect)
if param['Parameter6'] == '00' and param['Parameter7'] == '00'
log('FOUND X10 DEVICE!!!')
insteonID = padhex(param['Parameter5'])
else
insteonID = padhex(param['Parameter5']) + '.' + padhex(param['Parameter6']) + '.' + padhex(param['Parameter7'])
end
group = param['Parameter4']
recflags = param['Parameter3']
lnkdata1 = param['Parameter8']
lnkdata2 = param['Parameter9']
lnkdata3 = param['Parameter10']
#pack string to store for PLM Database
@currentrecord = recflags + group
@currentrecord += param['Parameter5'] + param['Parameter6'] + param['Parameter7']
@currentrecord += lnkdata1 + lnkdata2 + lnkdata3

#Add to plmdatabase
$plmdatabase << @currentrecord
log('record Flags:' + recflags)
#log('PLM database=' +$plmdatabase.inspect)
if (recflags[0] & 0x80) == 0x80 # Record is in use if true
end
if (recflags[0] & 0x40) == 0x40 # Controller if true
log('Controller')
else
log('Responder')
end

log('Insteon ID:' + insteonID + ', Group:' + group)

cmdComplete
sendGetNext()

end
### Support Routine for EZToDCE
def processExternalCommand(param)
#there is no current command
# THIS IS COMING FROM AN OUTSIDE SOURCE
#EG: Manually turning Light Switch On/Off
# process this command.
# Note, this is a standard message
### have to check here if child is mine!

# This is where I have to check for a broadcast command..
#if so, search the child databases for responders,
#and fire events for each responder.
#Message flag is in parameter9 Group command 0xCx (All-Link Broadcast Message Pg 42.)
#Group is in parameter8
#From InsteonID is parameters 3, 4, 5
if (param['Parameter9'].hex & 0xC0) == 0xC0 # Message is Broadcast
log('Rerouting to processBroadcastMessage')
processBroadcastMessage(param)
else
log('Process External Command:')
log('Param:' + param.inspect)

# there is no ack here. Simply Send COMMANDS back to DCE
# and Complete the recv..
case param['Parameter10'].hex #this is the command
when 0x01 #Assign to Group
log('Caught EXTERNAL Assign to Group')
processDeviceInfo(param)
recvComplete
when 0x02 #Delete from Group
when 0x02 #Delete from Group
log('Caught EXTERNAL Delete from Group')
recvComplete
when 0x10 # PING
log('Caught EXTERNAL Insteon PING result')
recvComplete


when 0x11 #ON
log('Caught EXTERNAL Insteon ON command result')
#on level is in cmd2
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
log('From:' +insID)
log('Device:' + $children[insID].to_s)
myDevFrom = $children[insID]
# check to see if I own child
if myDevFrom == nil
log('I do not control this device.')
else
reportStatus(myDevFrom, hextopercent(param['Parameter11']))
$currentcmd = 0
end
recvComplete



when 0x13 #OFF
log('Caught EXTERNAL Insteon OFF result')
#on level is in cmd2
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
if myDevFrom == nil
log('I do not control this device.')
else

reportStatus(myDevFrom, 0)

$currentcmd = 0
#log('EVENT and state SENT!!!.48:[10]=0')
end
recvComplete

when 0x6A #Thermostat Zone Command
log('Caught EXTERNAL Insteon Thermostat result')
#on level is in cmd2
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
if myDevFrom == nil
log('I do not control this device.')
else
#case param['Parameter11'].to_s
#when '00'
reportStatus(myDevFrom, hextoTempurature(param['Parameter11']))
$currentcmd = 0
#when '60' #humidity
#when '20'#setpoint
#log('EVENT and state SENT!!!.48:[10]=0')
end

when 0x6B #Thermostat Mode Command
log('Caught EXTERNAL Insteon Thermostat result')
#on level is in cmd2 ie( HEAT(0x04), COOL(0x05), or AUTO(0x06))
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
if myDevFrom == nil
log('I do not control this device.')
else
#reportStatus(myDevFrom, 0)
$currentcmd = 0
#log('EVENT and state SENT!!!.48:[10]=0')
end

when 0x6C #Thermostat Zone Cool Command
log('Caught EXTERNAL Insteon Thermostat result')
#on level is in cmd2
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
if myDevFrom == nil
log('I do not control this device.')
else
reportStatus(myDevFrom, hextoTempurature(param['Parameter11']))
$currentcmd = 0
#log('EVENT and state SENT!!!.48:[10]=0')
end

when 0x6D #Thermostat Zone Heat Command
log('Caught EXTERNAL Insteon Thermostat result')
#on level is in cmd2
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = insHb + "." + insMb + "." + insLb
myDevFrom = $children[insID]
if myDevFrom == nil
log('I do not control this device.')
else
reportStatus(myDevFrom, hextoTempurature(param['Parameter11']))
$currentcmd = 0
#log('EVENT and state SENT!!!.48:[10]=0')
end



when 0x15; log('Caught EXTERNAL Insteon Brighten Result')
when 0x16; log('Caught EXTERNAL Insteon DIM Result')
when 0x24; log('Caught EXTERNAL Insteon DO EE READ')
when 0x28; log('Caught EXTERNAL Insteon SET ADDRESS MSB')
when 0x29; log('Caught EXTERNAL Insteon POKE')
when 0x2A; log('Caught EXTERNAL Insteon POKE EXTENDED')
when 0x2B; log('Caught EXTERNAL Insteon PEEK')
when 0x2C; log('Caught EXTERNAL Insteon PEEK INTERNAL')
when 0x2D; log('Caught EXTERNAL Insteon POKE INTERNAL')
else
log('Unknown EXTERNAL Insteon Command.')
end
end
end
### Support Routine for EZToDCE
def processACK(param)
#log('In ProcessACK: Param7:' + param['Parameter7'])
#log('CurrentCmd=' + $currentcmd.to_s)
case param['Parameter7'].hex #Received an ack to THIS command
when 0x1 #Assign to Group
log('Got Assign to Group ACK')
$currentcmd = 0x01
$cmdqueue[0]['Command'] = 'InsStdMsg'
#processDeviceInfo(param)
#cmdComplete
when 0x2 #Delete from Group
when 0x10 # PING
log('Got PING ACK')
#cmdComplete
$currentcmd = 0x1
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x11 #ON
$currentcmd = 0x11
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x13 #OFF
$currentcmd = 0x13
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x6A #Thermostat Zone Command
$currentcmd = 0x6A
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x6B #Thermostat Control Command
$currentcmd = 0x6B
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x6C #Thermostat Cool Command
$currentcmd = 0x6C
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x6D #Thermostat Cool Command
$currentcmd = 0x6D
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x15 #Bright
$currentcmd = 0x15
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x16 #DIM
$currentcmd = 0x16
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x17 #Start Manual Change
when 0x18 #Stop Manual Change
when 0x19 #Status Request
# Status Request Acked - get ready for InsStdMsg
$currentcmd = 0x19
# change cmd to reflect InsStdMsg
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x24
log('Caught ACK for Insteon DO EE READ')
$currentcmd = 0x24
$cmdqueue[0]['Command'] = 'InsStdMsg'
when 0x28
log('Caught ACK for Insteon SET ADDRESS MSB')
$currentcmd = 0x28
$cmdqueue[0]['Command'] = 'InsStdMsg'

when 0x29
log('Caught ACK for Insteon POKE')
$currentcmd = 0x29
$cmdqueue[0]['Command'] = 'InsStdMsg'

when 0x2A
log('Caught ACK for Insteon POKE EXTENDED')
$currentcmd = 0x2A
$cmdqueue[0]['Command'] = 'InsStdMsg'

when 0x2B
#log('Caught ACK for Insteon PEEK')
$currentcmd = 0x2B
$cmdqueue[0]['Command'] = 'InsStdMsg'

when 0x2C
log('Caught ACK for Insteon PEEK INTERNAL')
$currentcmd = 0x2C
$cmdqueue[0]['Command'] = 'InsStdMsg'

when 0x2D
log('Caught ACK for Insteon POKE INTERNAL')
$currentcmd = 0x2D
$cmdqueue[0]['Command'] = 'InsStdMsg'

else
log('Unknown Insteon Cmd1')
end
end


def checkPeekData(param)

$remoteLinkRecord += param['Parameter11'].hex.chr
log('CURRENT REMOTE RECORD IS:')
debug($remoteLinkRecord)
if $remoteLinkRecord.length == 8
log('REMOTE RECORD COMPLETE!')
processRemoteRecord(param)
$remoteLinkRecord = ''
end
end


def processRemoteRecord(param)
#have to find MY address
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']
insID = padhex(insHb) + "." + padhex(insMb) + "." + padhex(insLb)

log('Processing remote Record below:')

@flags = "\nFrom Device:" + insID + "\nFlags:\n"

if ($remoteLinkRecord[0] & 0x02) == 0x02 # High water mark
@flags += "Not the last record\n"
else
@flags += "This IS the last record\n"
end

if ($remoteLinkRecord[0] & 0x80) == 0x80 # Record is in use
@flags += "Record In Use\n"
if ($remoteLinkRecord[0] & 0x40) == 0x40 # Controller/Responder
@flags += "I am a Controller of "
else
@flags += "I am a Responder of "
end
@insteonID = padhex("%X" %$remoteLinkRecord[2]) + '.'
@insteonID += padhex("%X" %$remoteLinkRecord[3]) + '.'
@insteonID += padhex("%X" %$remoteLinkRecord[4])

@group = "%X" %$remoteLinkRecord[1]
@flags += @insteonID + " Group:" + @group
@work = padhex("%X" %$remoteLinkRecord[0]) #Control byte
@work += padhex("%X" %$remoteLinkRecord[1]) # Group
@work += padhex("%X" %$remoteLinkRecord[2]) # ID HB
@work += padhex("%X" %$remoteLinkRecord[3]) # ID MB
@work += padhex("%X" %$remoteLinkRecord[4]) # ID LB
@work += padhex("%X" %$remoteLinkRecord[5]) # Data1
@work += padhex("%X" %$remoteLinkRecord[6]) # Data2
@work += padhex("%X" %$remoteLinkRecord[7]) # Data3
log('adding to:' + insID)
log('Value:' + @work)
$childdatabases[insID] << @work #add it to the database
# log('Current Database:' + $childdatabases.inspect)
#now to save the database to configuration.
savechilddatabases(insID)
# Now to check to see if the child exists as a record
if $childdatabases[@insteonID] == nil
log('InsteonID is NEW, adding Child database entry')
$childdatabases[@insteonID] = ['****************']
$rerun = true
sendAddtoPLM(@insteonID)
sendPing(@insteonID)
else
log('InsteonID:' + @insteonID.to_s + 'seems to exist in child databases')
log('CDB:' + $childdatabases.inspect)

end
else
@flags += "Record NOT in use\n"
end
log($aqua + @flags + $grey)
log2(@flags)
if ($remoteLinkRecord[0] & 0x02) == 0x02
sendRemoteGetNext(insID)
end
end

def savechilddatabases(insteonID)
#This takes the $childdatabase hash+array and encodes it to
# save it as a string.
@work = ''
#log($yellow + 'SaveChildDatabases::nitems:' + $childdatabases[insteonID].nitems.to_s)
#log($childdatabases[insteonID].inspect + $grey)
$childdatabases[insteonID].each{|record|
@work += record
}

#now to save the string...
setdeviceconfig(insteonID, @work)

end
def sendPing(insteonID)
insID = insteonID.split('.')
param = {'Command' => 'SndIns',
'Parameter1' => insID[0],
'Parameter2' => insID[1],
'Parameter3' => insID[2],
'Parameter4' => '0F',
'Parameter5' => '10', #ID Request
'Parameter6' => '00'}
$cmdqueue << param
log('PING Sent!')
end

def getdevicetemplate(cat, subcat)

log('Entered getdevicetemplate, Cat=' + cat.to_s + ', subcat = ' + subcat.to_s)
@templid = 0
case cat.hex
when 0x0 # Generalized Controllers
case subcat.hex
when 0x04; log('Found ControLinc [2430]')
when 0x05; log('Found RemoteLinc [2440]')
when 0x06; log('Found Icon Tabletop Controller [2830]')
when 0x09; log('Found SignaLinc RF Signal Enhancer [2442]')
when 0x0A; log('Found Balboa Instruments Poolux LCD Controller')
when 0x0B; log('Found Access Point [2443]')
when 0x0C; log('Found IES Color Touchscreen')
end
when 0x01 # Dimmable Lighting Control
# all these devices are associated with Template 38
# Light Switch (dimmable)
@templid = 38
case subcat.hex
when 0x00; log('Found LampLinc V2 [2456D3]')
when 0x01; log('Found SwitchLinc V2 Dimmer 600W [2476D]')
when 0x02; log('Found In-LineLinc Dimmer [2475D]')
when 0x03; log('Found Icon Switch Dimmer [2876D]')
when 0x04; log('Found SwitchLinc V2 Dimmer 1000W [2476DH]')
when 0x06; log('Found LampLinc 2-pin [2456D2]')
when 0x07; log('Found Icon LampLinc V2 2-pin [2456D2]')
when 0x09; log('Found KeypadLinc Dimmer [2486D]')
when 0x0A; log('Found Icon In-Wall Controller [2886D]')
when 0x0D; log('Found SocketLinc [2454D]')
when 0x13; log('Found Icon SwitchLinc Dimmer for Lixar/Bell Canada [2676D-B]')
when 0x17; log('Found ToggleLinc Dimmer [2466D]')
end
when 0x02 # Switched Lighting Control
# all these devices are associated with Template 37
# Light Switch (ON/OFF)
@templid = 37
case subcat.hex

when 0x09; log('Found ApplianceLinc [2456S3]')
when 0x0A; log('Found SwitchLinc Relay [2476S]')
when 0x0B; log('Found Icon On Off Switch [2876S]')
when 0x0C; log('Found Icon Appliance Adapter [2856S3]')
when 0x0D; log('Found ToggleLinc Relay [2466S]')
when 0x0E; log('Found Switchlinc Relay Countdown Timer [2476ST]')
when 0x10; log('Found In-LineLinc Relay [2475D]')
when 0x13; log('Found Icon SwitchLinc Relay for Lixar/Bell Canada [2676R-B]')
end
when 0x03 # Network Bridges
case subcat.hex
when 0x01; log('Found PowerLinc Serial [2414S]')
when 0x02; log('Found PowerLinc USB [2414U]')
when 0x03; log('Found Icon PowerLinc Serial [2814S]')
when 0x04; log('Found Icon PowerLinc USB [2814U]')
when 0x05; log('Found Smartlabs Power Line Modem Serial [2412S]')
end
when 0x04 # Irrigation Control
# all these devices are associated with Template 1780
# Standard Irrigation Sprinkler
@templid = 1780
case subcat.hex

when 0x00; log('Found Simplehomenet EZRain1 Sprinkler Controller')
end
when 0x05 # Climate Control
case subcat.hex
when 0x00; log('Found Broan SMSC080 Exhaust Fan')
when 0x01; log('Found Simplehomenet EZTherm')
when 0x02; log('Found Broan SMSC110 Exhaust Fan')
when 0x03
log('Found Venstar RF Thermostat Module')
@templid = 2198 #Set Template
when 0x04; log('Found Simplehomenet EZStat Thermostat')
end
when 0x06 # Pool and Spa Control
case subcat.hex
when 0x00; log('Found Simplehomenet EZPool')
end
when 0x07 # Sensors and Actuators
case subcat.hex
when 0x00
end
when 0x08 # Home Entertainment
case subcat.hex
when 0x00
end
when 0x09 # Energy Management
case subcat.hex
when 0x00
end
when 0x0A # Built-In Appliance Control
case subcat.hex
when 0x00
end
when 0x0B # Plumbing
case subcat.hex
when 0x00
end
when 0x0C # Communication
case subcat.hex
when 0x00
end
when 0x0D # Computer Control
case subcat.hex
when 0x00
end
when 0x0E # Window Coverings
case subcat.hex
when 0x00
end
when 0x0F # Access Control
case subcat.hex
when 0x00
end
when 0x10 # Security, Health, and Safety
when 0x11 # Surveillance
when 0x12 # Automotive
when 0x13 # Pet care
when 0x14 # Toys
when 0x15 # Timekeeping
when 0x16 # Holiday
end
return @templid
end

def processDeviceInfo(param)
### temporary
### 12-24-07 Adding Device Template compatibility..
#have to find MY address
insHb = param['Parameter3'] # From
insMb = param['Parameter4']
insLb = param['Parameter5']

insID = padhex(insHb) + "." + padhex(insMb) + "." + padhex(insLb)
#set the devicecat and device subcat in the childdatabases
# 0-1 Device Category
# 2-3 Device SubCategory
# 4-5 Device Firmware
log('proccessDeviceInfo:Insteon ID' + insID)
$childdatabases[insID][0][0..1] = param['Parameter6']
$childdatabases[insID][0][2..3] = param['Parameter7']
$childdatabases[insID][0][4..5] = param['Parameter8']
savechilddatabases(insID)
log('InsteonID: ' + insID)
#log('Child Config AFTER update:' + $childdatabases[insID][0].to_s)
log($yellow)
@template = getdevicetemplate(param['Parameter6'], param['Parameter7'])
$devicetemplate[insID] = @template
log('Template ID:' + @template.to_s)
### eventually, open a XML configuration script?
### or read saved data from mysql?
### most likely save this information to sql with device.
### eventually, IPKDB will be available to ping.
log('for Insteon ID:' + insID)
log($grey)
end

def recvComplete
# Clears the wait flag, but does not remove a command from the queue
$wAIT = false
log($green + "Receive Completed. Checking command queue" + $grey)
if $cmdqueue.nitems > 0 then
log("Queue:" + $aqua + $cmdqueue.nitems.to_s + $grey + " : executing next command")
SndIns()
else
log($yellow + 'Queue Empty.' + $grey)
if $rerun == true
log('RERUN=TRUE, RESTARTING')
$rerun = false
mainRestart()
else
log('RERUN Not needed. Checking if reported..')
#report Child devices here.
if $reported == false
log('Reporting Child Devices')
@work = ""
$childdatabases.each_key{
|insteonID|
log('Child:' + insteonID)
log('Config:' + $childdatabases[insteonID].inspect)
@template = $devicetemplate[insteonID]
@work += insteonID + "\t\t\t" + @template.to_s + "\t\n"
}
log(@work)
cmd = Command.new(device_.devid_, -1001, 1, 2, 54)
cmd.params_[13] = @work
SendCommand(cmd)

$reported = true
else
log('report not needed')
end
end

end
end
def removecurrentcommand
#get the current child
log('in RemoveCurrentCommand')
log('Current Command:' + $cmdqueue[0].inspect)
#id is in param123
@id = $cmdqueue[0]['Parameter1']
@id += '.' + $cmdqueue[0]['Parameter2']
@id += '.' + $cmdqueue[0]['Parameter3']
log('ID=' + @id)
#now to remove from child and PLM databases
removefromchild(@id)
removefromplm(@id)
cmdComplete
end
def cmdComplete
# Clears the wait flag, and removes the command from the queue.
$wAIT = false
$resetNext = 0
$cmdqueue.delete_at(0)
# now that THAT command is completed, check to see if there is
# another command ready to transmit.
log($green + "Command Completed." + $grey)
end
def checkWait(param)
#Checks for response from current command.
if $cmdqueue[0] != nil
if $wAIT == true
#log('CW:waiting for command to complete')
else
#log('CW:reports clear')
end
else
log('------:)----checkWait: command queue is emtpy')
if $wAIT == true #this should never happen
log('------:(XXX-CheckWait: TRUE')
end
end
end

def plmparse(value)
#THIS ROUTINE REPLACES parsestring()
#this routine will PARSE the incoming stream into valid messages
# value is the complete command
param = {}
#here is a special case, the PLM seems to lock up.
if value == 0x15.chr
log('The PLM stopped responding')
log('Please unplug it, and plug it back in')
log('and do a quick reload router.')

end
while value.length > 2
case value[1]
when 0x62 # Special case, need to look at flags
if (value[5] & 0x10) == 0x10 # check for extended flag
cmdlen = 23
else
cmdlen = 9
end
param['Response'] = 'SndIns'
when 0x50; cmdlen = 11; param['Response'] = 'InsStdMsg'
when 0x51; cmdlen = 25; param['Response'] = 'InsExtMsg'
when 0x68; cmdlen = 4 #Set Insteon ACK Message Byte
when 0x71; cmdlen = 5 #Set Insteon ACK Message Two Bytes
when 0x70; cmdlen = 4 #Set Insteon NACK Message Byte
when 0x63; cmdlen = 5; param['Response'] = 'SndX10'
when 0x52; cmdlen = 4; param['Response'] = 'X10Msg'
when 0x61; cmdlen = 6; param['Response'] = 'SndGrp'
when 0x56; cmdlen = 7; param['Response'] = 'GrpEvntRpt'
when 0x58; cmdlen = 3 #All-Link Cleanup Status Report
when 0x64; cmdlen = 5; param['Response'] = 'StLnk'
when 0x65; cmdlen = 3; param['Response'] = 'CancelLnk'
when 0x53; cmdlen = 10; param['Response'] = 'InsLnkSts'
when 0x69; cmdlen = 3; param['Response'] = 'GetLnk'
when 0x6A; cmdlen = 3; param['Response'] = 'GetNext'
when 0x6C; cmdlen = 3 #Get All-Link Record for Sender
when 0x57; cmdlen = 10; param['Response'] = 'LnkData'
when 0x6F; cmdlen = 12; param['Response'] = 'MngLnk'
when 0x67; cmdlen = 3; param['Response'] = 'RstPLM'
when 0x6B; cmdlen = 4; param['Response'] = 'SetCfg'
when 0x60; cmdlen = 9; param['Response'] = 'GetVersion'
when 0x66; cmdlen = 6 #Set Host Device Category
when 0x72; cmdlen = 3 # RF Sleep
when 0x54; cmdlen = 3; param['Response'] = 'BtnRpt'
when 0x6D; cmdlen = 3; param['Response'] = 'LEDON'
when 0x6E; cmdlen = 3; param['Response'] = 'LEDOFF'
else

log('ERROR IN PLMPARSE- Unknown Command')
debug(value)

return ''
end

#Now we know the length the command should be, see if we have it.
#log('waiting for ' + cmdlen.to_s + ' characters...')
#log('length of current input is ' + value.length.to_s)
if value.length >= cmdlen
#log('GOT whole response')
#Yes, we have the whole command, Pack it in param
for byt in 1..cmdlen
param['Parameter' + byt.to_s] = padhex("%X" %value[byt - 1])
end
#now remove it from the string..
value = value.slice(cmdlen, value.length - cmdlen)
#Send it off for parsing
#log('Sending to EZToDCE:' + param.inspect.to_s)
EZToDCE(param)
else
#log('Still waiting...')
#no, we have NOT received the whole command.

end
end
return value
end

def rawX10(value)

x10MSN = $X10HouseCodes.index[value[0..0]]
x10LSN = $X10UnitCodes.index[value[1..1]]
return x10MSN + x10LSN
end

def X10Flag(value)
return + $X10CommandCodes.index[Value] + '0'
end

def SndIns
# create a new PLM command for SndIns
if $wAIT == false
#log('SndIns:currentcmd=' + $currentcmd.to_s)

if $cmdqueue.nitems > 0
log("SndIns:Queue:" + $aqua + $cmdqueue.nitems.to_s + $grey)
#log('SndIns:' + $cmdqueue.inspect)
param = $cmdqueue[0]
### have to figure out the command byte 2 here
work = '02'.hex.chr + plmcommand(param)
### PLM command compilation
for loop in 2..param.keys.nitems
@dummy = param['Parameter' + (loop - 1).to_s].to_s
work+= @dummy.hex.chr
end
conn_.Reconnect()
debugout(work)
conn_.Send(work)
#sleep 0.1
$wAIT = TRUE
else
log($yellow + 'Queue Empty.' + $grey)
if $rerun == true
log('RERUN=TRUE, RESTARTING')
$rerun = false
mainRestart()
else
log('RERUN Not needed')
if $reported == false
log('Reporting Child Devices')
@work = ""
$childdatabases.each_key{
|insteonID|
log('Child:' + insteonID)
log('Config:' + $childdatabases[insteonID].inspect)
@template = $devicetemplate[insteonID]
@work += insteonID + "\t\t\t" + @template.to_s + "\t\n"
}
log(@work)
cmd = Command.new(device_.devid_, -1001, 1, 2, 54)
cmd.params_[13] = @work
SendCommand(cmd)

$reported = true
else
log('report not needed')
end
end

end
else
log('X-----------SndIns: Waiting for response to:' + $cmdqueue[0]['Command'].to_s)
log('X-----------SndIns: Current Queue Length:' + $cmdqueue.nitems.to_s)
end
end
def plmcommand(param)
### this returns the proper Byte2 for the command.
case param['Command']
when 'GetVersion'; return 0x60.chr
when 'SndIns'; return 0x62.chr
when 'SndGrp'; return 0x61.chr
when 'SndX10'; return 0x63.chr
when 'GetLnk'; return 0x69.chr
when 'GetNext'; return 0x6A.chr
when 'BtnRpt'; return 0x54.chr
when 'GetCfg'; return 0x73.chr
when 'StLnk'; return 0x64.chr
when 'CancelLnk'; return 0x65.chr
when 'MngLnk'; return 0x6F.chr
when 'RstPLM'; return 0x67.chr
when 'SetCfg'; return 0x6B.chr
when 'LEDON'; return 0x6D.chr
when 'LEDOFF'; return 0x6E.chr
## hack
when 'InsStdMsg'
log('ERROR:PLMCommand encountered a COMMAND of INSSTDMSG')
break
return 0x62.chr
end
end

def debug(text)
work = 'DEBUG:'

for c in 1..text.length
work += padhex("%X" %text[c-1]) + ' '
end
log($yellow + work + "Length:" + text.length.to_s + $grey)
end
def debugout(text)
work = 'out:'

for c in 1..text.length
work += padhex("%X" %text[c-1]) + ' '
end
log($green + work + "Length:" + text.length.to_s + $grey)
end
def debugin(text)
work = 'IN:'

for c in 1..text.length
work += padhex("%X" %text[c-1]) + ' '
end
log($red + work + "Length:" + text.length.to_s + $grey)
end

def padhex(hex)
if hex.length==1
hex = "0" + hex
end
return hex
end

def percenttohex(level)
# convert from percent to byte
return "%X" %((level.to_i * 2.55)).to_i
end

def hextopercent(level)
return ((level.hex.to_i / 2.55)).to_i
end

def hextoTempurature(degree) #Thermostat change hex to tempurature
return ((degree.hex.to_i / 2)).to_i
end
def Tempuraturetohex (degree) #Thermostat Cahnge tempurature to hex
return ((degree.to_1 * 2)).hex
end

def log(line)
$log = File.open("/var/log/pluto/" + device_.devid_.to_s + "_Generic_Serial_Device.log", "a")
$log.puts "(***):" + line.to_s
$log.close
end
def log2(line)
#this will send a message out the the orbiters..
#/usr/pluto/bin/MessageSend localhost 0 20 1 809 9 "Text to Display" 70 "alert" 182 "30" 251 "??"
cmd = Command.new(device_.devid_, -1000, 1, 1, 809)
cmd.params_[9] = line #text to display
cmd.params_[70] = 'PLMMessage' #Token
cmd.params_[182] = '10' #Timeout in seconds
cmd.params_[251] = '??'
SendCommand(cmd)
end
def checkChildRecordsinPLM()
log('Entered CheckChildRecordsinPLM')
# log('In CheckChildRecordsinPLM')
# time to verify all children are in the PLM
#
# log('Total PLM Records:' + $plmdatabase.nitems.to_s)
$plmdatabase.each{|record|
log('Record: = '+ getIIDfromRecord(record) + ' Group:' + getGroupfromRecord(record))
log('checking to see if it needs to be added as a child...')
if existsinchild(getIIDfromRecord(record)) == false

log(getIIDfromRecord(record) + ' needs to be added to the child database')
addtochild(getIIDfromRecord(record))
end
}

$childdatabases.each_key {|child|
if existsinplm(child) == false
log(child + ' needs to be added to PLM')
sendAddtoPLM(child)
else
log(child + ' exists in PLM')
end

#now to scan the childs database
for record in 1..($childdatabases[child].nitems - 1)
@test = $childdatabases[child][record]
if existsinplm(getIIDfromRecord(@test)) == false
log(getIIDfromRecord(@test) + ' needs to be added to PLM')
sendAddtoPLM(getIIDfromRecord(@test))
else
log(getIIDfromRecord(@test) + ' exists in PLM')
end
#Also check to see if it needs to be added in the childdatabases
end
}

end
def existsinplm(insteonid)
result = false
$plmdatabase.each{|record|
#log(insteonid + '==' + getIIDfromRecord(record))
if insteonid == getIIDfromRecord(record)
result = true
end
}
return result
end
def existsinchild(insteonid)
log('ExistsinChild:InsteonID:' + insteonid)
result = false
$childdatabases.each_key{|record|
if insteonid == record
result = true
end
}
log('ExistsinChild result:FALSE') if result == false
log('ExistsinChild result:TRUE') if result == true
return result
end
def addtochild(insteonID)
log('addtochild Routne called')
log('Adding ' + insteonID + ' to the child database...')
if insteonID.length == 2 then
log('Child is X10')
$state[insteonID] = 0
else
log('Child is Insteon')
$childdatabases[insteonID] = ['****************']
sendPing(insteonID)
$rerun = true
end
end


def removefromchild(insteonID)
log('Removing ' + insteonID + ' from child database')
$childdatabases.delete(insteonID)
$state.delete(insteonID)
end
def removefromplm(insteonID)
log('Removing from plm')
$plmdatabase.each{|record|
#log(insteonid + '==' + getIIDfromRecord(record))
if insteonID == getIIDfromRecord(record)
debug(record)
log('Found Record, Deleting')
$plmdatabase.delete(record)

#now, we have to remove it from the device.
param = {'Command' =>'MngLnk',
'Parameter1' => '80', #DELETE
'Parameter2' => record[0..1], #control byte
'Parameter3' => record[2..3], #group
'Parameter4' => record[4..5],#HB
'Parameter5' => record[6..7],#MB
'Parameter6' => record[8..9],#LB
'Parameter7' => record[10..11],#data1
'Parameter8' => record[12..13],#data2
'Parameter9' => record[14..15] #data3

}
log(param.inspect)
$cmdqueue << param
end
}
end
def sendAddtoPLM(insteonID)
log('Adding ' + insteonID + ' to the PLM database...')
#This adds a record into the PLM
@insID = insteonID.split('.')
param = {'Command' => 'MngLnk',
'Parameter1' => '40', #control code -- add new record as Controller
'Parameter2' => 'C2', #All Link Record Flags AKA Record Control Byte
'Parameter3' => '01', #All Link Group
'Parameter4' => @insID[0], #HB
'Parameter5' => @insID[1], #MB
'Parameter6' => @insID[2], #LB
'Parameter7' => '01', #Link Data 1 ON-Level
'Parameter8' => '01', #Link Data 2 Ramp Rate
'Parameter9' => 'FF'} #Link Data 3 not used
if $wAIT == true
$cmdqueue.insert(1, param)
else
$cmdqueue.insert(0, param)
end

SndIns()
end

def getIIDfromRecord(recordstring)
#this extracts the insteonID string from the record.
#log('getIIDfromRecord::recordstring:' + recordstring)
@idhb = recordstring[4..5]
@idmb = recordstring[6..7]
@idlb = recordstring[8..9]
@result = @idhb + '.' + @idmb + '.' +@idlb
#log('GetIIDfromRecord: Found ID:' + @result)
return @result
end

def processBroadcastMessage(param)
#search the child databases for responders,
#and fire COMMANDS for each responder. 06Feb08
#and fire events for each responder.XXXXXXXXXXXXX
#Message flag is in parameter9 Group command 0xCx (All-Link Broadcast Message Pg 42.)
#Group is in parameter8
#From InsteonID is parameters 3, 4, 5
group = param['Parameter8']
from = padhex(param['Parameter3']) + '.'
from += padhex(param['Parameter4']) + '.'
from += padhex(param['Parameter5'])
log('Looking for ' + from + ' Group:' + group)
log('Showing Parameter10:' + param['Parameter10'].to_s)
#Ok, now have to search child databases for from AND group AND responder
$childdatabases.each_key{|child|
#log('Searching:' + child)
for rec in 1..($childdatabases[child].nitems - 1)
record = $childdatabases[child][rec]
if getIIDfromRecord(record) == from # First, look for Insteon ID
#log('Found ID')
if getGroupfromRecord(record) == group #next, Group
#log('Found Group')
if isResponderRecord(record) # is a responder?
#log('Found Responder')
#figure out the child devicenum
from = $children[child]
#figure out the command
case param['Parameter10'].hex
when 0x11 #on
reportStatus(from, 100)
when 0x13 #off
reportStatus(from, 0)
when 0x6B # Thermostat Command On/OFF/AUTO
case param['Parameter11'].to_s
when '09' #status to OFF
#need to set current temp
reportStatus(from, 0)
else
#check thermostat for state and update and set current temp
#reportStatus(from, 100)
end

when 0x6C # Thermostat Command Cool Point
tempurature =param['Parameter11'] /2 #temp in hex need to devide by 2 = current cool point
#reportStatus(from,tempurature)
when 0x6D# Thermostat Command Heat Point
tempurature =param['Parameter11'] /2 #temp in hex need to devide by 2 = current heat point
#reportStatus(from,tempurature)

when 0x17 #dim/brighten -ignore
level = 0
when 0x18 # STOP dim/brighten - sendgetstatus
level = 0
sendGetChildStatus(child)
else
level = 0
log('Command is other than ON/OFF/Dim/Brighten')
end
end
end
end
end
}
end

def reportStatus(from, level)
log('From:' + from.to_s) #shows child id
log('current State:' + $state[from].to_s)
log('Wanted State:' + level.to_s)
case $state[from]
when 0
if level >=1
cmd = Command.new(from, from, 1, 1, 192) #on
cmd.params_[120] = "1"
SendCommand(cmd)
cmd = Command.new(from, from, 1, 1, 184)
cmd.params_[76] = level.to_s
cmd.params_[120] = "1"
SendCommand(cmd)
end
when 100
if level >= 1
cmd = Command.new(from, from, 1, 1, 184)
cmd.params_[76] = level.to_s
cmd.params_[120] = "1"
SendCommand(cmd)
else
cmd = Command.new(from, from, 1, 1, 193) # off
cmd.params_[120] = "1"
SendCommand(cmd)
end
else
if level == 100
cmd = Command.new(from, from, 1, 1, 193) #off
cmd.params_[120] = "1"
SendCommand(cmd)
cmd = Command.new(from, from, 1, 1, 192) # on
cmd.params_[120] = "1"
SendCommand(cmd)
end
cmd = Command.new(from, from, 1, 1, 184) #SetLevel
cmd.params_[76] = level.to_s
cmd.params_[120] = "1"
SendCommand(cmd)
end
log('ReportStatus: device:' + from.to_s + ' Status:' + level.to_s)
$state[from] = level
end

def isResponderRecord(recordstring)
work = recordstring[0..1].hex
if (work & 0x40) == 0x40 #check bit 6
result = false #signifies Controller record
else
result = true #signifies Responder record
end
return result
end

def getGroupfromRecord(recordstring)
#this extracts the GROUP from the record.
if recordstring == nil
return '00'
else
return recordstring[2..3]
end
end
def getdeltafromconfig(insteonID)
#This returns the delta from the child.
@work = $childdatabases[insteonID][0] # the settings stored in [0]
if @work == nil
return '00'
else
return @work[6..7]
end
end
def sendGetChildStatus(insteonID)
#log('sendGetChildStatus Called')
if insteonID.length != 2 #X10 device
@insID = insteonID.split('.')
param = {'Command' => 'SndIns',
'Parameter1' => @insID[0],
'Parameter2' => @insID[1],
'Parameter3' => @insID[2],
'Parameter4' => '0F', #flags
'Parameter5' => '19', #Status Request
'Parameter6' => '00'} #not used.
$cmdqueue << param
SndIns()
#Returned response will have cmd1 = DBDelta
#Returned response will have cmd2 = ON-Level
else
log('X10 does not report status')
end
end
def islast(record)
#high water mark
return false if (record[0..1].hex & 0x02) == 0x02
return true
end

def isinuse(record)
return true if (record[0..1].hex & 0x80) == 0x80
return false
end

def iscontroller(record)
return true if (record[0..1].hex & 0x40) == 0x40
return false
end
def group(record)
return record[2..3]
end
def remoteid(record)

@insteonID = record[4..5] + '.'
@insteonID += record[6..7] + '.'
@insteonID += record[8..9]
return @insteonID
end

def findresponderrecord(masterid, slaveid, groupid)
# log(masterid + ':' + slaveid + ':' + groupid)
$childdatabases[slaveid].each{|check|
# log('Record:' + check.to_s)
if iscontroller(check.to_s) == false #responder record
# log('found responder record')
# log('remoteid:' + remoteid(check.to_s))
if remoteid(check.to_s) == masterid # found
# log('Found Controller ID in responder record')
if group(check.to_s) == groupid
# log('Group Matches')
#found group
return true
end
end
end
}
return false
end
def findcontrollerrecord(masterid, slaveid, groupid)
# log(masterid + ':' + slaveid + ':' + groupid)
$childdatabases[masterid].each{|check|
# log('Record:' + check.to_s)
if iscontroller(check.to_s) == true #controller
# log('found controller record')
if remoteid(check.to_s) == slaveid # found
# log('found Responder ID in Controller record')
if group(check.to_s) == groupid
# log('Group Matches')
#found group
return true
end
end
end
}
return false
end

# time to define a structure to save the raw data in hex
# starts at [0]
# Bytes Meaning
# 0-1 Device Category
# 2-3 Device SubCategory
# 4-5 Device Firmware
# 6-7 Database Delta
# 8-9 reserved
# 10-11 reserved
# 12-13 reserved
# 14-15 reserved
###### First database record below (in same format its read from the device)
###### This is the same format as an ALL-Link Record Response from the PLM
###### (0x57) bytes 3..10
# 16-17 record control byte
# 18-19 Group
# 20-21 ID HB
# 22-23 ID MB
# 24-25 ID LB
# 26-27 Link Specific Data1
# 28-29 Link Specific Data2
# 30-31 Link Specific Data3
######
# 32-47 next database record...