Difference between revisions of "VDR Manual Install on LinuxMCE 710"
(→Core) |
m (VDR Manual Install moved to VDR Manual Install on LinuxMCE 710: The installation instructions are for 710 only. On 810 VDR installs automatically) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | [[Category:Tutorials]] | |
Everything mentioned below is based from a clean lmce0710 amd64 installation. | Everything mentioned below is based from a clean lmce0710 amd64 installation. | ||
| Line 5: | Line 5: | ||
Create a channels.conf as explained in lmce wiki an dupload through webadmin. | Create a channels.conf as explained in lmce wiki an dupload through webadmin. | ||
| − | Download | + | Download [http://www.linuxmce.org/vdr-LMCE0710-10.tar.gz vdr-1.6.0-6_LMCE0710-10.tar.gz] |
| − | + | =Install specific instructions for Core and MD. (only app binaries)= | |
| − | + | ==Core== | |
Unpack tar.gz file in /home/linuxmce | Unpack tar.gz file in /home/linuxmce | ||
| Line 21: | Line 21: | ||
Check if vdr load on startup, xineliboutput and streamdev-server plugin. | Check if vdr load on startup, xineliboutput and streamdev-server plugin. | ||
| − | + | ==MD== | |
ssh into your core. | ssh into your core. | ||
sudo su - | sudo su - | ||
| Line 35: | Line 35: | ||
| − | + | =Development= | |
If you need to build other VDR plugins you need to install vdr-dev. | If you need to build other VDR plugins you need to install vdr-dev. | ||
It is located in directory named optional. | It is located in directory named optional. | ||
| Line 44: | Line 44: | ||
==Core== | ==Core== | ||
| − | Build your channels.conf file | + | Build your channels.conf file |
| − | apt-get install dvb-utils | + | apt-get install dvb-utils |
| − | /etc/init.d/vdr stop | + | /etc/init.d/vdr stop |
scan -o vdr /usr/share/dvb/scan/dvb-t/<FILENAME> > channels.conf | scan -o vdr /usr/share/dvb/scan/dvb-t/<FILENAME> > channels.conf | ||
Upload channels.conf in webadmin. | Upload channels.conf in webadmin. | ||
Latest revision as of 06:21, 3 August 2010
Everything mentioned below is based from a clean lmce0710 amd64 installation.
Create a channels.conf as explained in lmce wiki an dupload through webadmin.
Download vdr-1.6.0-6_LMCE0710-10.tar.gz
Contents
Install specific instructions for Core and MD. (only app binaries)
Core
Unpack tar.gz file in /home/linuxmce
cd vdr0710-10 cd <into directory named i386 or amd64 depending on which architecture you use> cd common dpkg -i *.deb (answer yes to question if config file should be replaced) cd .. cd core dpkg -i *.deb /etc/init.d/vdr restart
Check if vdr load on startup, xineliboutput and streamdev-server plugin.
MD
ssh into your core.
sudo su - ssh moonXX (where XX is the number of your MDs) cd /home/linuxmce cd <into directory named i386 or amd64 depending on which architecture you use> Remember that you MD can run a different architecture than your core. cd common dpkg -i *.deb (answer yes to question if config file should be replaced) cd .. cd md dpkg -i *.deb /etc/init.d/vdr restart
Development
If you need to build other VDR plugins you need to install vdr-dev. It is located in directory named optional.
Configuration
Core
Build your channels.conf file
apt-get install dvb-utils /etc/init.d/vdr stop scan -o vdr /usr/share/dvb/scan/dvb-t/<FILENAME> > channels.conf
Upload channels.conf in webadmin.
You need to modify some settings to allow liveTV to work on MDs. The files that you have to edit is:
In /etc/vdr/plugins/streamdev.conf add line:
0.0.0.0/0
or uncomment if it already exist.
In /var/lib/vdr/setup.conf (remember /etc/init.d/vdr stop before you edit any config files) Add lines: (at the end)
streamdev-server.AllowSuspend = 1 streamdev-server.MaxClients = 6 streamdev-server.StartHTTPServer = 1 streamdev-server.StartVTPServer = 1 streamdev-server.SuspendMode = 1
MD
/et/init.d/vdr stop
Edit /var/lib/vdr/setup.conf Add lines:
streamdev-client.RemoteIp = 192.168.80.1 streamdev-client.RemotePort = 2004 streamdev-client.StartClient = 1 streamdev-client.StreamFilters = 0 streamdev-client.SyncEPG = 0
posde The original instructions by niz23 called for SyncEPG = 1 on the MD.
