Difference between revisions of "EIB/KNX Devices"
(added note about US EIB/KNX components from Siemens) |
(→EIB/KNX in the USA) |
||
| (One intermediate revision by one other user not shown) | |||
| Line 12: | Line 12: | ||
The 6987/10 can be used as a PSU for the TP bus for up to 5 TP devices. | The 6987/10 can be used as a PSU for the TP bus for up to 5 TP devices. | ||
| + | |||
| + | Add to that a KNX/IP gateway (or other support KNX-2-computer gateway), and you can control your EIB/KNX over Powernet setup from LinuxMCE. | ||
| + | |||
== EIB/KNX in the USA == | == EIB/KNX in the USA == | ||
Siemens has a few actors, which are US-specific (110/120V) | Siemens has a few actors, which are US-specific (110/120V) | ||
| Line 18: | Line 21: | ||
All low-voltage sensors, like switch plates, PIRs etc from around the world should be usable in the USA, as they are independent of the mains. | All low-voltage sensors, like switch plates, PIRs etc from around the world should be usable in the USA, as they are independent of the mains. | ||
| + | |||
| + | It seems a company called [http://www.elementcontrols.com/ Element Controls] does have quite a few KNX devices in the US as well. Maybe they would like to sponsor a few devices to one of our main devs, so he can get accustomed with KNX in the US. | ||
Latest revision as of 12:57, 19 March 2011
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | Unknown | N/A | N/A |
| 810 | Unknown | N/A | N/A |
| 1004 | Unknown | N/A | N/A |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
To connect LinuxMCE (with the "old" driver) with your EIB/KNX environment you MUST use a serial bus connector. I use a Berker FT1.2 (order nr. 750600xx). If you try to use the new driver, you can use any connector because it works with eibd (EIB/KNX with eibd).
EIB/KNX over Powernet
There is no direct serial bus connector for EIB over Powernet. One way to circumvent this problem, is to use a "Systemkoppler 6987/10" from Busch-Jäger.
The Systemkoppler is used to connect EIB over Powernet to an EIB over Twisted Pair installation. All telegrams pass easily between those installs.
The 6987/10 can be used as a PSU for the TP bus for up to 5 TP devices.
Add to that a KNX/IP gateway (or other support KNX-2-computer gateway), and you can control your EIB/KNX over Powernet setup from LinuxMCE.
EIB/KNX in the USA
Siemens has a few actors, which are US-specific (110/120V)
- Binary Actor (8-port) 5WG1 512-1CB01.
- Power Supply 5WG1123-1CB01
All low-voltage sensors, like switch plates, PIRs etc from around the world should be usable in the USA, as they are independent of the mains.
It seems a company called Element Controls does have quite a few KNX devices in the US as well. Maybe they would like to sponsor a few devices to one of our main devs, so he can get accustomed with KNX in the US.
