Medion MD1 NBC: Difference between revisions

Latest revision as of 15:14, 29 September 2010

Version	Status	Date Updated	Updated By
710	Unknown	N/A	N/A
810	Unknown	N/A	N/A
1004	Unknown	N/A	N/A
1204	Unknown	N/A	N/A
1404	Unknown	N/A	N/A
Usage Information

Medion MD1 NBC

Medion MD1 NBC (Made in China by X10) is a RF Remote Controler.

It has all (almost) what you need to control your LinuxMCE. It uses 2 x 1.5V AAA batteries.

P/N: 20018268
FCC ID: B4S20018268

I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.

X10 Receiver

The X10 RF receiver need to be connected directly into the mainboard USB pin.

P/N: 20018267

Technical Specification:

It has CE mark so it is approved for use in the EU.

RF Frequency: 433 MHz
Operating range: 30m or 60feet (open field)
Can support up to 16 remotes
Works through walls using RF technology even when not aimed at the receiver

Setup

The device works with LMCE using LIRC. I`ve configured my device using Add_support_for_new_remote_controls guide.

Note:LinuxMCE will automatically load ati_remote kernel module which doesn`t seem to work. You need to prevent doing this by either doing

echo "blacklist ati_remote" >>/etc/modprobe.d/blacklist as root or deleting the module.

My lircd.conf.

@@ Line 1: / Line 1: @@
 [[Category: Hardware]]
+{{versioninfo}}
 [[Category: Input]]
-[[Category: Supported]]
+===Medion MD1 NBC===
+[[Image:Medion-MD1-NBC.jpg|Medion MD1 NBC RF Remote Control]]
+Medion MD1 NBC (Made in China by X10) is a RF Remote Controler.
-[[Image:Medion-MD1-NBC.jpg|thumb|200px|Medion MD1 NBC RF Remote Control]]
+It has all (almost) what you need to control your LinuxMCE.
+It uses 2 x 1.5V AAA batteries.
+*P/N: 20018268
+*FCC ID: B4S20018268
-Medion MD1 NBC (Made in China by X10) is a RF Remote Controler, I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.
+I`ve got it along with KNC ONE TV-Station DVR analog tv tuner card.
-==X-10 Receiver==
-The X-10 RF receiver need to be connected directly into the mainboard USB pin.
-This is an European version it works in
+===X10 Receiver===
-RF Frequency: 433 MHz
+The X10 RF receiver need to be connected directly into the mainboard USB pin.
+*P/N: 20018267
+Technical Specification:
+It has CE mark so it is approved for use in the EU.
+*RF Frequency: 433 MHz
+*Operating range: 30m or 60feet  (open field)
+*Can support up to 16 remotes
+*Works through walls using RF technology even when not aimed at the receiver
+===Setup===
 The device works with LMCE using LIRC. I`ve configured my device using [[Add_support_for_new_remote_controls]] guide.
+'''Note:'''LinuxMCE will automatically load '''ati_remote''' kernel module which doesn`t seem to work.
+You need to prevent doing this by either doing
+<code>
+echo "blacklist ati_remote" >>/etc/modprobe.d/blacklist<br>
+</code>
+as root or deleting the module.
+My [[Medion-MD1-NBC-lirc.conf|lircd.conf]].