Difference between revisions of "Message Translation"
| Line 3: | Line 3: | ||
Used to translate between ''toggle'' and ''discrete'' commands (usually for infrared equipment). | Used to translate between ''toggle'' and ''discrete'' commands (usually for infrared equipment). | ||
When a device only accepts toggle commands and it receives an "ON" or "OFF", it will be translated into "TOGGLE_POWER" depending on device status. | When a device only accepts toggle commands and it receives an "ON" or "OFF", it will be translated into "TOGGLE_POWER" depending on device status. | ||
| − | Same is true then device accepts | + | Same is true then device accepts discrete commands, but the remote has only toggle button, in this case we will send "ON" or "OFF", again it depends on device state. |
== Available translations == | == Available translations == | ||
| + | === Power === | ||
| + | * ON/OFF to TOGGLE_POWER | ||
| + | * TOGGLE_POWER to ON/OFF | ||
| + | === Inputs === | ||
| + | * AN INPUT to (one/many) INPUT_SELECT | ||
| + | * INPUT_SELECT to one of the INPUTS | ||
| + | You'll have to set up corectly input sequence for this to work as expected. | ||
| + | |||
| + | ==== List of available inputs ==== | ||
| + | RGB | ||
| + | Video 1 | ||
| + | Video 2 | ||
| + | Video 3 | ||
| + | Video 4 | ||
| + | Video 5 | ||
| + | Tape / Tape 1 | ||
| + | TV | ||
| + | CD | ||
| + | Phono | ||
| + | Aux | ||
| + | DVD | ||
| + | Tuner | ||
| + | Video 6 | ||
| + | Video 7 | ||
| + | AM | ||
| + | FM | ||
| + | DVD Multi | ||
| + | Aux 2 | ||
| + | Tape 2 | ||
| + | Minidisc | ||
| + | Tuner 2 | ||
| + | VDP | ||
| + | Laserdisc | ||
| + | DSS | ||
| + | DVI | ||
| + | Svideo | ||
| + | Composite | ||
| + | RF Input | ||
| + | DBS/Satellite | ||
| + | VCR-1 | ||
| + | VCR-2 | ||
| + | VCR-3 | ||
| + | V.AUX | ||
| + | AV 1 | ||
| + | AV 2 | ||
| + | AV 3 | ||
| + | SVideo/YC 1 | ||
| + | SVideo/YC 2 | ||
| + | SVideo/YC 3 | ||
| + | Tuner 3 | ||
| + | WB | ||
| + | SW | ||
| + | HDMI | ||
| + | D4 | ||
| + | Input 1 | ||
| + | Input 2 | ||
| + | Input 3 | ||
| + | Input 4 | ||
| + | Input 5 | ||
| + | Input 6 | ||
| + | Input 7 | ||
| + | Input 8 | ||
| + | Input 9 | ||
| + | Input 10 | ||
| + | Radio | ||
| + | Antenna | ||
| + | CDR | ||
| + | DAT | ||
| + | External 1 | ||
| + | External 2 | ||
| + | External 3 | ||
| + | Component 1 | ||
| + | Component 2 | ||
| + | DVR | ||
| + | Composite 2 | ||
| + | HDMI 2 | ||
| + | RGB 2 | ||
| + | PC | ||
| + | HD | ||
| + | AV 4 | ||
| + | AV 5 | ||
| + | AV 6 | ||
| + | AV 7 | ||
| + | AV 8 | ||
Revision as of 14:01, 23 May 2006
| This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto. |
Used to translate between toggle and discrete commands (usually for infrared equipment). When a device only accepts toggle commands and it receives an "ON" or "OFF", it will be translated into "TOGGLE_POWER" depending on device status. Same is true then device accepts discrete commands, but the remote has only toggle button, in this case we will send "ON" or "OFF", again it depends on device state.
Available translations
Power
- ON/OFF to TOGGLE_POWER
- TOGGLE_POWER to ON/OFF
Inputs
- AN INPUT to (one/many) INPUT_SELECT
- INPUT_SELECT to one of the INPUTS
You'll have to set up corectly input sequence for this to work as expected.
List of available inputs
RGB Video 1 Video 2 Video 3 Video 4 Video 5 Tape / Tape 1 TV CD Phono Aux DVD Tuner Video 6 Video 7 AM FM DVD Multi Aux 2 Tape 2 Minidisc Tuner 2 VDP Laserdisc DSS DVI Svideo Composite RF Input DBS/Satellite VCR-1 VCR-2 VCR-3 V.AUX AV 1 AV 2 AV 3 SVideo/YC 1 SVideo/YC 2 SVideo/YC 3 Tuner 3 WB SW HDMI D4 Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Input 9 Input 10 Radio Antenna CDR DAT External 1 External 2 External 3 Component 1 Component 2 DVR Composite 2 HDMI 2 RGB 2 PC HD AV 4 AV 5 AV 6 AV 7 AV 8
