Revision as of 16:30, 12 September 2013

Installation of LinuxMCE in a KVM Virtual Machine

On this page I will describe the installation process of LinuxMCE in a KVM virtual machine. As a host system I use proxmox, a very user friendly and easy to use bare metal hypervisor.

Download Required Software

Download Proxmox the latest version of proxmox: [1]

At the moment of this writing the current version is Proxmox VE 3.1

Download LinuxMCE [2]

At the moment of this writing the current version is LinuxMCE 1004 final

Adittionally if you are on Windows and want to use a usb-stick: (you do not need any addidional program on Linux)

Suse Studio Image Writer [3] to write the image to a usb-stick. UnetBootin and Rufus do not work.

Copying Image to USB-Stick

If you want to use a CD simply burn the iso to a cd.

On Linux

Please make sure that /dev/XYZ is the right device, as this delets all content. Please also note that this is the device WITHOUT the number for the partition. SO for example /dev/sdc AND NOT /dev/sdc1 pve-cd.iso is the current proxmox iso that you downloaded.

dd if=pve-cd.iso of=/dev/XYZ bs=1M

On Windows

First delete the partition of the usb-stick, else Suse Studio Image Writer might fail with a access failed error. Then rename the Proxmox iso that you downloaded from .iso to .raw. Run Suse Studio Image Writer, selct the drive and the image.

Base Installation of Proxmox

The graphical installation guide is straightforward and easy to understand. Please note though that the installer DELETS ALL PARTITIONS ON THE SELECTED DRIVE! So all data on that drive is lost! You might want to unhook all harddrives that have unsaved data on it just to make sure you do not pick the wrong one by accident.

Reboot and Settings

After the base installation reboot the system, and check if you put in the right ip data in the installation process. NOTE: if you have multiple newtork cards make sure you plug the cable into the right one, if you do not have network connection try the other one.

Networking

Networking should work out of the box, if it does you can ignore this chapter and continue with Update. Else: check if there is internet connectivity by pinging something.

ping google.com

If you want to change the network settings

nano /etc/network/interfaces

if you want to use dhcp for the public interface this should look like:

auto lo
iface lo inet loopback
auto vmbr0
iface vmbr0 inet dhcp

If you want to use static it should look something like that:

auto lo
iface lo inet loopback
auto vmbr0
iface vmbr0 inet static
      address 192.168.0.13
      netmask 255.255.255.0
      gateway 192.168.0.1
      bridge_ports eth0
      bridge_stp off
      bridge_fd 0

if you did change some network setting run

/etc/init.d/networking restart

Update

run

aptitude update && aptitude full-upgrade

If you get the message

E: Some index files failed to download. They have been ignored, or old ones used instead.

you can ignore it, or if rather not you can edit

nano /etc/apt/sources.list.d/pve-enterprise.list

and comment out the enterpries repository by placing a "#" in front of it.

#deb https://enterprise.proxmox.com/debian wheezy pve-enterprise

Software Raid

If you do not want to use softwar raid you can continue with the next chapter. WARNING: Software raid is not supported by proxmox! But of course it works nevertheless, but as usual do it on your own risk. This part of the guide is based in a German guide found here[4] First install the required package:

apt-get update; apt-get install mdadm

If there are any prompts on installing mdadm just ignore or press yes.

Prepare Raid

If you have not done so yet shutdown and plugin the second (identical) drive. In this guide the harddrive that proxmox was installed on is /dev/sda, while the second to use in the raid is /dev/sdb. If you have different drive letter, please change them accordingly. Prepare and create raid:

sfdisk -d /dev/sda | sfdisk -f /dev/sdb
sfdisk -c /dev/sdb 1 fd
sfdisk -c /dev/sdb 2 fd
mdadm --create -l1 -n2 /dev/md0 missing /dev/sdb1
mdadm --create -l1 -n2 /dev/md1 missing /dev/sdb2

copy /boot to the new raid md. (Note: md with raid means "multiple device" and has nothing to do with media director)

mkfs.ext3 /dev/md0
mkdir /mnt/md0
mount /dev/md0 /mnt/md0
cp -ax /boot/* /mnt/md0

Then edit the fstab

nano /etc/fstab

and find the line for boot that says

UUID=xxxxxxxxx /boot ext3 defaults 0 1

and change it to

/dev/md0 /boot ext3 defaults 0 1