User:Purps

Introduction

Hello all. My name is Matt and I live in England. Have been playing with LMCE for a number of years now. I would class myself as a user due to my complete lack of any development skills, so am always keen to help in any way I can. By profession I am a Mechanical Design Engineer in the space industry. In my spare time I enjoy metalwork, woodwork and various other little electronics projects. Any remaining free time is spent with my extremely patient and long-suffering girlfriend with whom I live.

Software Installation

My current installation is based on the 23388 snapshot http://linuxmce.iptp.org/snapshots/

The following is a list of things I had to do that deviate from a "normal" install http://wiki.linuxmce.org/index.php/Installing_0810

• Edited the /etc/apt/sources.list as per http://forum.linuxmce.org/index.php?topic=10901.0

Network

The skeleton of your LMCE system. It is highly advisable that you adopt the recommended network setup and use 2 NICs in your core. This means that a) things a lot more likely to work straight out of the box and b) when things DO go wrong, you are far more likely to receive support. In my experience it is definitely worth it.

My external network looks a little bit like this...

Wall -> Cable Modem (my ISP is Virgin Media) -> NIC 1 (eth0) on core

And my internal network...

NIC 2 (eth1) on core -> Netgear 8-port Gigabit switch

Connected to this switch there are another two Netgear Gigabit switches (switches can be daisy-chained to give you more ports). Connected to these you'll find...

• All of the MDs
• "Normal" computers requiring internet access
• Netgear wireless router
• IP Cameras
• DECT phone (via ATA)

Quick note on the wireless router; this acts as a Wireless Access Point, nothing more. Just connect it up via the port you would usually plug your internet cable into. In the router's admin page, make sure DHCP is enabled, and then set it up in the normal way. Your SSID should NOT give any clues as to where you live, use the strongest encryption you can (I use WPA2) and it makes a lot of sense to set up an access list (MAC filter). This allows you to specify exactly which MAC addresses are allowed to connect, making your wireless access point very secure.

Core/MDs

This section talks about the main bits of hardware in my home that make up the principal elements of any LMCE system.

Security

Cameras

Panasonic Foscam PoE for both

Tool Time

This is where I plan to place a few Howto videos for various DIY projects that can be carried out around the house, in order to achieve that seamless, perfectly integrated LMCE installation. The aim will be to stay away from technical jargon as much as possible, and use standard/simple tools and components that aren't going to break the bank.

• Howto: Construct a rear mounting MD casing for any TV screen with a VESA mount (with slot loading DVD drive).
• Howto: Mount a TV on the wall with MD hidden behind (with a slot loading DVD drive).
• Howto: Make a wall-mounted orbiter (inspired by Techstyle's framing idea). Surface mounted or recessed (flush fitting)?
• Howto: Install a new back box (e.g. for z-wave light switch) and make good the wall (having destroyed it in the process).
• Howto: Chase wall channels, embed cables and make good the wall.
• Howto: Build a single/double bed with integrated "stowable" flat screen TV and MD. LMCE-controlled motor perhaps.
• Howto: Build a waterproof bathroom MD/orbiter (combined touchscreen device?)
• Howto: Make your own ceiling/wall speakers using (decent!) multimedia speakers (if, like me, you are not a complete audiophile, this avoids having an external amp to hide away).
• Howto: Build your own charging cradle/stand for your mobile orbiter (avoid switching it off all the time).
• Howto: Make your own cat6 patch cables