Difference between revisions of "ACT Homepro ZIR010"

From LinuxMCE
Jump to: navigation, search
m (New page: Category: Hardware Category: Climate Category: ZWave == PIR (Binary Sensor) support == PIR (Passive Infra Red) sensor, a type of motion detector which uses invisible infra re...)
 
 
(23 intermediate revisions by 7 users not shown)
Line 1: Line 1:
 
[[Category: Hardware]]
 
[[Category: Hardware]]
[[Category: Climate]]
+
{{versioninfo|710Status=According to category, Works without caveats|710UpdatedDate=11th May 2010|710UpdatedBy=[[User:Wierdbeard65|Wierdbeard65]]|810Status=According to category, Works without caveats|810UpdatedDate=11th May 2010|810UpdatedBy=[[User:Wierdbeard65|Wierdbeard65]]|}}
 +
 
 +
{| align="right"
 +
  | __TOC__
 +
  |}
 +
[[Category: Security]]
 
[[Category: ZWave]]
 
[[Category: ZWave]]
 +
[[Category: ZWave_security]]
 +
[[Category: ZWave_motion_sensor]]
 +
[[Category: Works without caveats on 0710]]
 +
[[Category: Works without caveats on 0810]]
  
== PIR (Binary Sensor) support ==
+
= ACT Homepro Passive Infrared Motion Detector (Binary Sensor) =
  
 
PIR (Passive Infra Red) sensor, a type of motion detector which uses invisible infra red light to detect movement in a room.
 
PIR (Passive Infra Red) sensor, a type of motion detector which uses invisible infra red light to detect movement in a room.
PIR is sending "Sensor Tripped" events, so that you can use it in security scenarious.
+
PIR is sending "Sensor Tripped" events, so that you can use it in security scenarios.
  
All the tests were made using HomePro ZIR000 (RF Transmitter PIR) model.
+
All the tests were made using [[ACT Homepro ZIR010]] (RF Transmitter PIR) model.
  
 
=== HowTo install PIR ===
 
=== HowTo install PIR ===
 +
# Open the PIR box so that you have access to Z-Wave button, it is used to remove/add (reset) the PIR from/to Z-Wave network
 +
# Use your Z-Wave Master Controller to add PIR
 +
# Copy the new Z-Wave network configuration to your Z-Wave USB device (see command "Download Configuration")
 +
# Reload Router
 +
# You should see the PIR device available as a child device of ZWave (see [[LinuxMCE Admin Website]]), but the setup isn't ready yet.
 +
# Power off PIR, then power on again (remove a battery for few seconds). Close the PIR box.
 +
##  This step is important because PIR is in awake state only for 10 min after it's powered up.
 +
# After 2-3 min from step 6, PIR will send the wake up notification and PIR will be able to set its configuration.
 +
# You should receive the events from PIR
  
  1) Open the PIR box so that you have access to Z-Wave button, it is used to remove/add (reset) the PIR from/to Z-Wave network
+
=== Device configuration ===
  2) Use your Z-Wave Master Controller to add PIR
+
 
  3) Copy the new Z-Wave network configuration to your Z-Wave USB device (see command "Download Configuration")
+
The PIR supports three modes, they can be set with the device parameter #17:
  4) Reload Router
+
 
  5) You should see the PIR device available as a child device of ZWave (see LinuxMCE admin web pages), but the setup isn't ready yet.
+
* Lighting (configuration value 0): Sends ON/OFF to associations in group 1, sends ON to devices associated to group 2 when housing is opened
  6) Power off PIR, then power on again (remove a battery for few seconds). Close the PIR box.
+
* Alarm mode (configuration value 1): Sends ALARM to associations in group 1, sends ALARM to group 2 when housing is opened
  This step is important because PIR is in awake state only for 10 min after it's powered up.
+
* Sensor mode (configuration value 2): Sends a binary sensor report to group 1, sends update to group 2 when housing is opened
  7) After 2-3 min from step 6, PIR will send the wake up notification and PIR will be able to set its configuration.
+
 
  8) You should receive the events from PIR
+
Battery reports are sent to all devices associated to group 3 of the PIR.
 +
 
 +
The OFF/IDLE delay can be set via parameter #18. The values 0-255 represent 0-255 minutes.
 +
 
 +
The device can be temporary disabled by setting parameter #19 to 0. Setting it to 1 will re-enable the PIR.
 +
 
 +
The wake-up time can be adjusted with parameter #22. The values 15 - 45 represent 15 to 45 seconds.  
  
 
=== Notes ===
 
=== Notes ===
  
  1) PIR needs 2 min of 'silence' to get to Trigger Off
+
* Battery lasts between 6 months and two years
  2) Z-Wave has some new commands to support PIR :
+
* PIR needs 2 min of 'silence' to get to Trigger Off
    - Assign Return Route
+
* Z-Wave has some new commands to support PIR :
    - Set Association
+
** Assign Return Route
    - Set Configuration Parameter
+
** Set Association
    - Set Wake Up
+
** Set Configuration Parameter
  The configuration commands are sent automatically by LinuxMCE's ZWave device.
+
** Set Wake Up
  But if you are using a different PIR device and you need another setup parameters, you can use the new commands.
+
** The configuration commands are sent automatically by LinuxMCE's [[Z-Wave]] device. But if you are using a different PIR device and you need another setup parameters, you can use the new commands.
  3) The PIR wake up notification is important, no commands are sent to PIR if the notification wasn't received.
+
* The PIR wake up notification is important, no commands are sent to PIR if the notification wasn't received.
  We must be sure that PIR is able to communicate with Z-Wave network.
+
**  We must be sure that PIR is able to communicate with Z-Wave network.
 +
 
 +
= Specifications =
 +
* Power: 4 AAA batteries
 +
* Dimensions (mounted): 10.47cm x 6.6cm x 7.8cm
 +
 
 +
= Command Classes =
 +
* BASIC_TYPE_ROUTING_SLAVE
 +
* GENERIC_TYPE_SENSOR_BINARY
 +
 
 +
== Supports ==
 +
* COMMAND_CLASS_SENSOR_BINARY
 +
* COMMAND_CLASS_ALARM
 +
* COMMAND_CLASS_WAKE_UP
 +
* COMMAND_CLASS_ASSOCIATION
 +
* COMMAND_CLASS_CONFIGURATION
 +
* COMMAND_CLASS_BATTERY
 +
* COMMAND_CLASS_MANUFACTURER_SPECIFIC
 +
* COMMAND_CLASS_VERSION
 +
 
 +
== Controls ==
 +
*COMMAND_CLASS_BASIC
 +
 
 +
= Links =
 +
http://www.elekhomica.nl/product_info.php?cPath=91&products_id=589
 +
 
 +
http://www.act-solutions.com/HomePro/HomePro.shtml
 +
 
 +
Available in the UK - Techstyle UK Ltd.
 +
[http://www.techstyleuk.co.uk/index_files/zir010.htm ACT ZIR010 Z-Wave Passive Infra-Red detector (PIR) Motion Detector]

Latest revision as of 16:39, 28 September 2010

Version Status Date Updated Updated By
710 According to category, Works without caveats 11th May 2010 Wierdbeard65
810 According to category, Works without caveats 11th May 2010 Wierdbeard65
1004 Unknown N/A N/A
1204 Unknown N/A N/A
1404 Unknown N/A N/A
Usage Information

ACT Homepro Passive Infrared Motion Detector (Binary Sensor)

PIR (Passive Infra Red) sensor, a type of motion detector which uses invisible infra red light to detect movement in a room. PIR is sending "Sensor Tripped" events, so that you can use it in security scenarios.

All the tests were made using ACT Homepro ZIR010 (RF Transmitter PIR) model.

HowTo install PIR

  1. Open the PIR box so that you have access to Z-Wave button, it is used to remove/add (reset) the PIR from/to Z-Wave network
  2. Use your Z-Wave Master Controller to add PIR
  3. Copy the new Z-Wave network configuration to your Z-Wave USB device (see command "Download Configuration")
  4. Reload Router
  5. You should see the PIR device available as a child device of ZWave (see LinuxMCE Admin Website), but the setup isn't ready yet.
  6. Power off PIR, then power on again (remove a battery for few seconds). Close the PIR box.
    1. This step is important because PIR is in awake state only for 10 min after it's powered up.
  7. After 2-3 min from step 6, PIR will send the wake up notification and PIR will be able to set its configuration.
  8. You should receive the events from PIR

Device configuration

The PIR supports three modes, they can be set with the device parameter #17:

  • Lighting (configuration value 0): Sends ON/OFF to associations in group 1, sends ON to devices associated to group 2 when housing is opened
  • Alarm mode (configuration value 1): Sends ALARM to associations in group 1, sends ALARM to group 2 when housing is opened
  • Sensor mode (configuration value 2): Sends a binary sensor report to group 1, sends update to group 2 when housing is opened

Battery reports are sent to all devices associated to group 3 of the PIR.

The OFF/IDLE delay can be set via parameter #18. The values 0-255 represent 0-255 minutes.

The device can be temporary disabled by setting parameter #19 to 0. Setting it to 1 will re-enable the PIR.

The wake-up time can be adjusted with parameter #22. The values 15 - 45 represent 15 to 45 seconds.

Notes

  • Battery lasts between 6 months and two years
  • PIR needs 2 min of 'silence' to get to Trigger Off
  • Z-Wave has some new commands to support PIR :
    • Assign Return Route
    • Set Association
    • Set Configuration Parameter
    • Set Wake Up
    • The configuration commands are sent automatically by LinuxMCE's Z-Wave device. But if you are using a different PIR device and you need another setup parameters, you can use the new commands.
  • The PIR wake up notification is important, no commands are sent to PIR if the notification wasn't received.
    • We must be sure that PIR is able to communicate with Z-Wave network.

Specifications

  • Power: 4 AAA batteries
  • Dimensions (mounted): 10.47cm x 6.6cm x 7.8cm

Command Classes

  • BASIC_TYPE_ROUTING_SLAVE
  • GENERIC_TYPE_SENSOR_BINARY

Supports

  • COMMAND_CLASS_SENSOR_BINARY
  • COMMAND_CLASS_ALARM
  • COMMAND_CLASS_WAKE_UP
  • COMMAND_CLASS_ASSOCIATION
  • COMMAND_CLASS_CONFIGURATION
  • COMMAND_CLASS_BATTERY
  • COMMAND_CLASS_MANUFACTURER_SPECIFIC
  • COMMAND_CLASS_VERSION

Controls

  • COMMAND_CLASS_BASIC

Links

http://www.elekhomica.nl/product_info.php?cPath=91&products_id=589

http://www.act-solutions.com/HomePro/HomePro.shtml

Available in the UK - Techstyle UK Ltd. ACT ZIR010 Z-Wave Passive Infra-Red detector (PIR) Motion Detector