Difference between revisions of "GlobalCache GC-100"

From LinuxMCE
Jump to: navigation, search
m (None)
Line 45: Line 45:
 
== How to ==
 
== How to ==
 
=== Install ===
 
=== Install ===
The device is not quite [[plug&play]]. You have to perform a factory reset and to add it from orbiter ("Add GC100" button). LMCE will temporarily change its internal network and look for the gc100 at its factory default of 192.168.1.70, change the configuration of the GC100, and the core then goes back to its regular network settings. Note that this will almost certainly fail if your '''exernal''' IP on the core is in the 192.168.1 network! The script will then install needed software and after that it should say that device is ready to use (don't forget to [[quickreload]]).
+
The device is not quite [[plug&play]]. You have to perform a factory reset and to add it from orbiter ("Add GC100" button). LMCE will temporarily change its internal network and look for the gc100 at its factory default of 192.168.1.70, change the configuration of the GC100, and the core then goes back to its regular network settings. Note that this will almost certainly fail if your '''exernal''' IP on the core is in the 192.168.1 network! The script will then install needed software and after that it should say that device is ready to use (don't forget to [[quickreload]]).
  
 
==== Complete Manual Install ====
 
==== Complete Manual Install ====
Line 134: Line 134:
 
   '''return "''00:00:00:00:00:00''"''';
 
   '''return "''00:00:00:00:00:00''"''';
 
    
 
    
   `curl <nowiki>http://192.168.1.70/Commands.cgi</nowiki> -o gc100mac1 --silent`;
+
   `curl &lt;nowiki>http://192.168.1.70/Commands.cgi&lt;/nowiki> -o gc100mac1 --silent`;
   `curl <nowiki>http://192.168.1.101/Commands.cgi</nowiki> -o gc100mac2 --silent`;
+
   `curl &lt;nowiki>http://192.168.1.101/Commands.cgi&lt;/nowiki> -o gc100mac2 --silent`;
 
   open(FILE,"gc100mac1");
 
   open(FILE,"gc100mac1");
   @data1 = <FILE>;
+
   @data1 = &lt;FILE>;
 
   close(FILE);
 
   close(FILE);
  
Line 156: Line 156:
 
  sub configure_webgc {
 
  sub configure_webgc {
 
     $local_ip = shift;
 
     $local_ip = shift;
     system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.70/commands.cgi?2=$local_ip&3=255.255.255.0&4=$gw&Y=0&7=submit\"");
+
     system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.70/commands.cgi?2=$local_ip&amp;3=255.255.255.0&amp;4=$gw&amp;Y=0&amp;7=submit\"");
     system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.101/commands.cgi?2=$local_ip&3=255.255.255.0&4=$gw&Y=0&7=submit\"");
+
     system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.101/commands.cgi?2=$local_ip&amp;3=255.255.255.0&amp;4=$gw&amp;Y=0&amp;7=submit\"");
 
}
 
}
 
or if you do it all manually from the command line:
 
or if you do it all manually from the command line:
  wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.1.70/commands.cgi?2=192.168.80.23&3=255.255.255.0&4=192.168.80.1&Y=0&7=submit"
+
  wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.1.70/commands.cgi?2=192.168.80.23&amp;3=255.255.255.0&amp;4=192.168.80.1&amp;Y=0&amp;7=submit"
 
and adapt to the desired IP address.
 
and adapt to the desired IP address.
  
  
 
You can now edit the port speed with the browser. If your browser hangs when you submit, you can use this the following wget call instead:
 
You can now edit the port speed with the browser. If your browser hangs when you submit, you can use this the following wget call instead:
  wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.80.23/serial.cgi?C=1&B=5&F=0&A=submit"
+
  wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.80.23/serial.cgi?C=1&amp;B=5&amp;F=0&amp;A=submit"
  
 
==== Firmware version 3.0 and later ====
 
==== Firmware version 3.0 and later ====
  
gc100 with firmware version 3.0 and later is Plug&Play, but not yet supported as such by LinuxMCE. It implements a DHCP client and also has a discovery beacon. Because it is able to get an IP address from the DHCP server, you won't be able to add it using the manual method describe here when using a default installation. You either have to use the completely manual installation procedure described on the [http://plutohome.com/wiki/index.php/Gc100#Complete_Manual_Install Plutohome Wiki for gc100], if you know what IP address the DHCP server gave it, or temporarily disable the DHCP server on the core (write down the DHCP settings, because they are erased from the database when you disable the DHCP server from Pluto-Admin - you can also /etc/init.d/dhcp3-server stop, add the gc100 and /etc/init.d/dhcp3-server start, without erasing the database).
+
gc100 with firmware version 3.0 and later is Plug&amp;Play, but not yet supported as such by LinuxMCE. It implements a DHCP client and also has a discovery beacon. Because it is able to get an IP address from the DHCP server, you won't be able to add it using <span class="plainlinks">[http://www.thepiggybackrider.com/ <span style="color:black;font-weight:normal; text-decoration:none!important; background:none!important; text-decoration:none;/*CITATION*/">child carrier</span>]</span> the manual method describe here when using a default installation. You either have to use the completely manual installation procedure described on the , if you know what IP address the DHCP server gave it, or temporarily disable the DHCP server on the core (write down the DHCP settings, because they are erased from the database when you disable the DHCP server from Pluto-Admin - you can also /etc/init.d/dhcp3-server stop, add the gc100 and /etc/init.d/dhcp3-server start, without erasing the database).
  
 
== Implementation details ==
 
== Implementation details ==

Revision as of 08:11, 27 September 2011

Version Status Date Updated Updated By
710 Unknown N/A N/A
810 Unknown N/A N/A
1004 Unknown N/A N/A
1204 Unknown N/A N/A
1404 Unknown N/A N/A
Usage Information
GC 100

GC100 is a network-capable device which allows you to add remote control (and other input device) connectivity. It includes:

  • serial ports
  • Infrared sensors (inputs) and outputs
  • one or more relays

The remote control data is then able to be sent over an Ethernet (TCP/IP) network through the Ethernet port, without the requirement of a connection to a specific PC.

For more details about the product check the Global Cache manufacturer web site.

Demo videos:

Send IR codes

LinuxMCE implementation of GC100 assumes that in device tree we'll have children and the messages are actually addressed to them instead of GC100 itself.

So when you are sending "ON" to TV controlled by GC100, the message is routed to the GC100, it finds infrared code for "ON" for that specific TV, sends a command to gc100 to send a specific infrared sequence, which will blink IR sender connected to specific port, and the TV will turn on.

The only two commands that GC100 implements itself are : CMD_Send_Code used to test which IR is suitable for your equipment and CMD_Learn_IR used to learn new IR codes.

Learn IR codes

The learning device is actually unrelated to GC100. It may be plugged into one of GC100's serial ports (don't forget to set them to 9600 bps), or in regular serial port, just be sure you specified right port in GC100 device data.

There are several other devices that support learning of infrared codes : IRTrans, Tira, USB_UIRT.

Learning is done from web page. When clicking "Learn" gc100 will start a thread that will try to get data from the port. If nothing is received in 30 seconds the thread will die. The page will continue to refresh trying to see if anything was added, but after 30 seconds it's useless.

Sensors

The gc100 jacks are by default configured as IR transmitters, but they can be configured to function as sensors. The sensors are, in their most basic form, two wires connected to a jack plug. When you cross them, a "sensor tripped" event is emitted. I am not currently aware of how this is supposed to function, who will intercept the event and how will it react to it. One idea for using a sensor is attaching a doorbell button to it, which, when pressed, will notify you in some way.

You must go into the gc100's web panel and set the input jack to 'sensor w/ auto notify' to use an i/r jack for a sensor.

How to

Install

The device is not quite plug&play. You have to perform a factory reset and to add it from orbiter ("Add GC100" button). LMCE will temporarily change its internal network and look for the gc100 at its factory default of 192.168.1.70, change the configuration of the GC100, and the core then goes back to its regular network settings. Note that this will almost certainly fail if your exernal IP on the core is in the 192.168.1 network! The script will then install needed software and after that it should say that device is ready to use (don't forget to quickreload).

Complete Manual Install

NOTE: Perform those steps if automation installation is not working! In 2.0.0.44 Gc-100 can be installed from the Orbiter by pressing the button 'Add GC100' but the device should have factory IP!

Factory reset the GC100. Connect it with a crossover cable to your pc. Change the ip address of your pc to the same network. Expl.: 192.168.1.101. Take a webbrowser and go to http://192.168.1.70.

Make two changes:

1. Serial: Change it to 4800/8/1/N (If you would like to connect a CM11 to it), 2. Network: Change it to your Network, outside of the pluto DHCP range.

Take a note of the MAC address of your GC100

In the pluto admin:

1. Add a new device. Choose the GC100 template 2. Edit the new device 3. Enter your IP Adress 4. Enter the MAC Address of your GC100. Example: 00:0c:11:22:33:44

Now reload everything.

Before the first use

  • Insert proper wires in relays, devices in serial ports, IR LEDs and/or sensors.
  • Go to device's webpage and set proper inputs/outputs, baud rates and so on.
  • Add child devices in LinuxMCE-admin webpage and set proper device data to match the wiring.

This should do it.

Changes in LinuxMCE 0710 beta 4

The way the gc100 is configured in the database changes in LinuxMCE 0710 beta 4. If you are upgrading from a previous release and have a gc100 set up, you will have to reconfigure it.

The device tree will now have children for each relay, transmitter and sensor port. These are autodetected depending on the settings made to the gc100 itself and updated as the settings change.

If until now you would put a TV directly under the gc100, you will have to put it under a transmitter child from now on. This will tell the gc100 which port to use to send the code, instead of sending it using all available transmitters like it did until now. This will allow you to add more IR devices which use the same codes without stepping on each other's toes, since the IR codes will be routed just to the target device. The old functionality is still in place and you can still add a TV directly under the gc100, but make sure you mark the checkbox that says "Don't autoconfigure" if you don't want the gc100 to manage its children, so your device remains in its place.

This is also true for relays. Add your lights, or other devices that support On and Off commands, under the relay children. The On and Off commands will be routed to the right relay this way.

Known Problems

MAC detection

--Nite man 06:03, 25 January 2008 (PST) To solve the MAC detection problem replace the function get_gc100mac() in the script /usr/pluto/bin/gc100-conf.pl by new one below:

sub get_gc100mac {
   my($mac, $page, $ret);

   `curl http://192.168.1.70/Commands.cgi -o gc100mac1 --silent`;
   `curl http://192.168.1.101/Commands.cgi -o gc100mac2 --silent`;

   open FILE, "gc100mac1";
   $ret = read FILE, $page, -s "gc100mac1";
   close FILE;

   unless($page) {
       open FILE, "gc100mac2";
       $ret = read FILE, $page, -s "gc100mac2";
       close FILE;
   }

   ($mac) = $page =~ /((?:[\dA-F]{2}-){5}[\dA-F]{2})/i;

   if($mac) {
       $mac =~ tr/\-/\:/;
       loggc("Mac Found $mac\n");
       system "rm -f gc100mac1 gc100mac2";
       return $mac;
   } else { exit 1 }

}

or apply that [gc100-conf.pl.patch]

Currently the support for the gc100 in LinuxMCE is broken, at least for some models or firmware versions. The /usr/pluto/bin/gc100-conf.pl script is for some reason unable to determine the gc100's MAC Adress after it has been reset to factory defaults. As a result it is only half configured and not added to the system properly.

The only known workaround [1] [2] at this time is to manually edit the perl script, and hardcode the MAC address of your gc100. In short, find this line in the script:

sub get_gc100mac {

Then insert this line immediately following it (replace 00:00:00:00:00:00 with the adress of your gc100):

return "00:00:00:00:00:00";

As a result it should look something like this now:

        exit(4);
  }
} 
    
sub get_gc100mac {
  
  return "00:00:00:00:00:00";
  
  `curl <nowiki>http://192.168.1.70/Commands.cgi</nowiki> -o gc100mac1 --silent`;
  `curl <nowiki>http://192.168.1.101/Commands.cgi</nowiki> -o gc100mac2 --silent`;
  open(FILE,"gc100mac1");
  @data1 = <FILE>;
  close(FILE);

Reset the gc100 to factory defaults if necessary and you should be able to add it from an orbiter as described above.

Another possible workaround might be described on the Plutohome wiki for the gc100, under Complete Manual Install.

Firmware versions known to be affected:

  • 2.4-06 (GC100-06)

Serial Port

Previous problems in the gc100-serial-bridge.sh script were fixed in 0710 beta4.

The GC100 serial port needs to be setup for 4800 bauds.

In some cases the gc100 may respond with "configuration is locked". If that happens, you need to re-configure the gc100 manually from factory defaults. In the /usr/pluto/bin/gc100-conf.pl, modify the wget call in the "sub configure_webgc" function to add parameter "Y=0" which means "do not lock config":

sub configure_webgc {
   $local_ip = shift;
   system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.70/commands.cgi?2=$local_ip&3=255.255.255.0&4=$gw&Y=0&7=submit\"");
   system("wget -q -T 3 --read-timeout=4 -t 1 \"http://192.168.1.101/commands.cgi?2=$local_ip&3=255.255.255.0&4=$gw&Y=0&7=submit\"");

} or if you do it all manually from the command line:

wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.1.70/commands.cgi?2=192.168.80.23&3=255.255.255.0&4=192.168.80.1&Y=0&7=submit"

and adapt to the desired IP address.


You can now edit the port speed with the browser. If your browser hangs when you submit, you can use this the following wget call instead:

wget -q -T 3 --read-timeout=4 -t 1 "http://192.168.80.23/serial.cgi?C=1&B=5&F=0&A=submit"

Firmware version 3.0 and later

gc100 with firmware version 3.0 and later is Plug&Play, but not yet supported as such by LinuxMCE. It implements a DHCP client and also has a discovery beacon. Because it is able to get an IP address from the DHCP server, you won't be able to add it using child carrier the manual method describe here when using a default installation. You either have to use the completely manual installation procedure described on the , if you know what IP address the DHCP server gave it, or temporarily disable the DHCP server on the core (write down the DHCP settings, because they are erased from the database when you disable the DHCP server from Pluto-Admin - you can also /etc/init.d/dhcp3-server stop, add the gc100 and /etc/init.d/dhcp3-server start, without erasing the database).

Implementation details

In gc100.cpp there is a lot of code for format conversion and other stuff. Practically it's not a big deal it receives a command, find a proper IR sequence and sends it to gc100.

Operating the relays, IR transmitters, and sensors

The gc100 software architecture uses two threads to communicate with the gc100 regarding relays, IR transmitters and sensors, one for sending messages (SocketThread) and one for receiving (EventThread). The reason for this is that the gc100 protocol isn't completely a request-reply protocol, even if it seems like that at first. The gc100 can initiate a transmission when a sensor is tripped, enough to break the request-reply paradigm. The program was designed to treat the communication as asynchronous. Messages are sent to the device without expecting a reply, and the replies are treated as independent events and state change reports, without linking a request to a reply in the program logic (except for the initialization phase).