Difference between revisions of "Hauppauge Nova-HD-S2"

From LinuxMCE
Jump to: navigation, search
Line 17: Line 17:
  
  
The DVB-S element on this card has run successfully on LMCE 0710 using VDR.
+
This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in LMCE 0710.
 +
 
 +
The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.
  
 
Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.
 
Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.
 +
 +
See [http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4000 here] for further information on driver status, and how to compile the multiproto driver.
  
  

Revision as of 11:16, 3 July 2008

Novahds2 top.jpg


Digital satellite TV and radio for your PC. Watch free-to-air satellite TV, in a window or full screen on your PC! Record digital satellite TV to your PC's hard disk in original MPEG-2 quality. Digital TV recordings will typically take 1,5 Gigabytes of disk space per hour. Pause digital satellite TV with instant replay. Listen to digital satellite DVB-S/DVB-S2 radio. DiSEqC 1.0 support. Includes Hauppauge new IR remote control, for easy control of TV watching, record and play functions.


Driver Information

This card uses the same DVB-S and DVB-S2 hardware as the HVR-4000. Therefore, this wiki also applies to getting the DVB-S element of the HVR-4000 card working in LMCE 0710.

The DVB-S element on the NOVA-HD-S2 has run successfully on LMCE 0710 using VDR.

Unfortunately, the current version of VDR does not support HD / DVB-S2 (as of LMCE 0710). The driver listed here only gets the DVB-S element running. In later versions of LMCE this will become obsolete, particularly when later versions of VDR are used. The experimental VDR 0.7.X will only work using Multiproto drivers, but these will support the DVB-S2 element of this card.

See here for further information on driver status, and how to compile the multiproto driver.


Installing The Drivers and Firmware

Download the patched v4l-dvb driver from here


Change into the downloaded directory, and open up a konsole. Type:


make

sudo make install


Now fetch the firmware:


wget ftp://167.206.143.11/outgoing/Oxford/88x_2_119_25023_WHQL.zip


unzip:


unzip -jo 88x_2_119_25023_WHQL.zip Driver88/hcw88bda.sys


and put it in place:


dd if=hcw88bda.sys of=/lib/firmware/dvb-fe-cx24116.fw skip=81768 bs=1 count=32522


now reboot, and check that the card has loaded


dmesg | grep cx88


you should get an output stating "hvr-4000-lite / Nova-HD-S2" somewhere.



Scan for Channels

see here for the VDR wiki


Instead of the scan command used in the VDR wiki I used:


scan -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf


Where my satellite is Astra-28.2E (the BSkyB (Sky-tv-uk) satellite)


To scan free-to-air channels only add an "-x 0" in the command. e.g.


scan -x 0 -o vdr .kde/share/apps/kaffeine/dvb-s/Astra-28.2E > channels.conf


Add the created channels.conf to VDR in the LMCE admin / advanced / configuration / VDR setup as per the VDR wiki