Difference between revisions of "Implementing Arduino using Generic Serial Device"

From LinuxMCE
Jump to: navigation, search
(Arduino Uno - 1004 Setup)
(Arduino Uno Setup)
Line 96: Line 96:
  
  
'''Prepare the Arduino Uno;'''
+
'''Arduino Uno shopping list'''
  
 
Shopping list:
 
Shopping list:
  
 
Arduino Uno
 
Arduino Uno
 +
 
Ethernet Shield
 
Ethernet Shield
 +
 +
LED
 +
 +
Resistors
 +
 
IDE installed on computer
 
IDE installed on computer
  

Revision as of 14:53, 9 September 2012

Version Status Date Updated Updated By
710 Unknown N/A N/A
810 Unknown N/A N/A
1004 In Progress 3th September 2012 Daballiem0
1204 Unknown N/A N/A
1404 Unknown N/A N/A
Usage Information

General Info (Information not valid yet)

Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments.

Arduino can sense the environment by receiving input from a variety of sensors and can affect its surroundings by controlling lights, motors, and other actuators. The microcontroller on the board is programmed using the Arduino programming language (based on Wiring) and the Arduino development environment (based on Processing). Arduino projects can be stand-alone or they can communicate with software running on a computer (e.g. Flash, Processing, MaxMSP).

Arduino uno test.jpg

Setting up Arduino Uno and LinuxMCE to be able to control a RGB LED string

In the following I want to give an overview what needs to be done to have LinuxMCE control a RGB LED (string) through an Arduino. The string is within brackets as the only added to the Arduino to be able to control a ledstring is some mosfets and a powerblock.

Setting up Linuxmce

For now define Arduino as a vendor via Advanced -> Device Templates. Select the "Add Manufacturer" button and provide "Arduino" as manufacturer followed by save and close.

Define a new template for the Arduino Uno (which I am using atm)

Advanced -> Device Templates, selected "Add device template". Name the template "Arduino Uno", select Implements DCE, Device Category is "Interfaces - Specialized #97". Specify that your device is controlled via category "Device Category:Core" ("Computers - Core"). Otherwise the driver will not be started on the core. As I am using an Ethernet shield select "Is IP based", set "Comm Method" to Ethernet and under "Device data" add #69 TCP Port (int). Give the TCP Port the value "69", set it to required and allowed to modify.

Now set up the rest of the template according to http://wiki.linuxmce.org/index.php/How_to_add_your_own_GSD_device

#384 Process Receive Command For Child

cmdId = cmd.id_ # Command ID: ON, OFF, SET LEVEL
cmdTo = cmd.devidto_ # Device ID in LinuxMCE
devPort = device_.childdevices_[cmdTo].devdata_[12] # 12 contains a port/channel
childType = device_.childdevices_[cmdTo].devtemplid_ # Template ID to know type of device: switch or dimmer

deviceID = device_.childdevices_[cmd.devidto_].devdata_[12]

command = [0,0,0,0,0,0] # define command array

command [0] = ''                                  # Parameter
command [1] = ''                                  # Parameter
command [2] = ''                           	  # Parameter
command [3] = ''                                  # Parameter
command [4] = ''                                  # Parameter
command [5] = ''                                  # Parameter
command [6] = ''                                  # Parameter    

log ('logging from #384');
log ('Device ID');
log cmdTo;
log ('Port used');
log command[2];
log ('Command given');                             # orginal command from LMCE
log cmdId;
log ('Device Template');                           # Template ID ie switch, dimmer or RGB
log childType;
log ('Level');
log cmd.params_[76];                               # The level to set, as a value between 0 (off) and 100 (full).
                                                   # It can be preceeded with a - or + indicating a relative value.  +20 means up 20%.


case cmdId

when 192                                           # 192 is the 'ON' command
command [0] = 'P'                                  # Start indication is P (Power)
command [1] = 'on-'                                # '1' indicating 'ON'  
command [2] = deviceID                             # Port number defined in LMCE

when 193                                           # 193 is the 'OFF' command
command [0] = 'P'                                  # Start indication is P (Power)
command [1] = 'off-'                               # '1' indicating 'OFF'  
command [2] = deviceID                             # Port number defined in LMCE

when 184                                           # 184 is Level of dimmer
command [0] = 'D'                                  # indicate level command
command [1] = deviceID                             # Port number defined in LMCE
command [2] = '-'
command [3] = cmd.params_[76]                      # is level coming from LMCE

when 980                                           # 980 is color scenario command (template 1993)
command [3] = '3'                                  # indicate RGB command
command [4] = cmd.params_[279]                     # red level
command [5] = cmd.params_[280]                     # green level
command [6] = cmd.params_[281]                     # blue level
end


commandstring = command.to_s                       # wrap the command array into a string
log ('Sending');                                   # log that we are sending
log commandstring;                                 # put in logfile what we send
conn_.Send commandstring                           # send if off

Arduino Uno Setup

Arduino Uno shopping list

Shopping list:

Arduino Uno

Ethernet Shield

LED

Resistors

IDE installed on computer

Sketch to upload to Arduino;

/*
 * Arduino LMCE interlink
 *
 * A basic example displaying the ability of LinuxMCE
 * to control an LED on an Arduino with
 * an ethernet shield.
 * 
 * Daballiemo
 * http://linuxmce.org
 */
#include <SPI.h>
#include <Ethernet.h>
int switchPin = 2;
int LEDpin = 5;						//LED set to pin 5
int x;
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };		//must give WIZnet a MAC
byte ip[] = { 192, 168, 80, 129 };				//must configure WIZnet IP
EthernetServer server = EthernetServer(69);			//TCP port the server is listening on, I'm using port 69, but you could use any
void setup()
{
 Ethernet.begin(mac, ip);
 server.begin();
 Serial.begin(9600);						//for troubleshooting purposes (not needed)
 pinMode(LEDpin, OUTPUT);
 pinMode(switchPin, INPUT);                                    // sets the digital pin as input to read switch
}
void loop () {
EthernetClient client = server.available();			//client connects to server
if (client){							//if connection present
 x = client.read();						//read information coming from server
 Serial.println(x);}						//print to serial (troublshooting only)
if (x == 49){							//if information sent is a zero
 digitalWrite(LEDpin, LOW);}					//turn of LED
else if (x == 48){						//if information sent is a one
 digitalWrite(LEDpin, HIGH);}				        //turn on LED
else if (x == 2){						//if information sent is a two
 digitalWrite(LEDpin, HIGH);					//blink the LED
 delay(500);
 digitalWrite(LEDpin, LOW);
 delay(500);}
if (digitalRead(switchPin) == 1){
 Serial.println("Button has been pressed " );
 server.write("Button has been pressed ");}                    // Read the pin and display the value
}