Difference between revisions of "Radio Thermostat"

From LinuxMCE
Jump to: navigation, search
Line 1: Line 1:
 
[[Category: Hardware]]  
 
[[Category: Hardware]]  
 
[[Category: Thermostats]]  
 
[[Category: Thermostats]]  
[[Category: Z-Wave Thermostat]]  
+
[[Category: Z-Wave]]  
[[Category: Wi-Fi Thermostat]]  
+
[[Category: Wi-Fi]]  
[[Category: Zigbee Thermostat]]  
+
[[Category: Zigbee]]  
  
  

Revision as of 00:50, 28 September 2015


Radio Thermostat makes several thermostats that can communicate via various wireless protocols using USNAP modules. This is an attempt to bring some of the information for these thermostats into one place.

Current Models are:

 CT-22 (Beginning to be depreciated)
 CT-30 (Also known as Filtrete 3M-50 sold in Home Depot in the U.S. with a slightly different case)
 CT-80

The USNAP communication modules include Wi-Fi, Zigbee and Z-Wave. Store Front

There is a Windows program to control it via Wi-Fi

These thermostats will connect on their own via a Wi-Fi Access Point back to their hosted control service and allow you to control your thermostat from any browser.

The documentation for the Wi-Fi communication API was released.

I also found this unofficial Cloud API documentation.

Driver is complete and waiting for sqlCVS approval. -Aviator

[1]

The template is in process but is #2235. The code below is under development:

#193 off:

data = "{\"tmode\":" # Current mode of HVAC operation
data+="0}" # Off
log("tmode set data: " + data)
tstat_set(data)

  1. 192 on:


data+="3}" # Auto
log("tmode set data: " + data)
tstat_set(data)

  1. 279 set fan:


data = "{\"fmode\":"
if onoff == "1"
data+="2}" # Fan is always on
else
data+="0}" # Auto
end

log("fmode set data: " + data)
tstat_set(data)

  1. 280 set heat/cool:


data = "{\"tmode\":"
if onoff == "H"
data+="1" # Heat only
elsif onoff == "C"
data+="2" # Cool only
else
data+="3" # Auto
end

data+="}"

log("tmode set data: " + data)

tstat_set(data)

  1. 278 set temperature:


if ((value_to_assign[0,1]=="+") || (value_to_assign[0,1]=="-"))
# The new setpoint is relative to the current setpoint
new_temp = celcius_to_farhenheit(Float(@setpoint)).round + value_to_assign.to_i
else
# The new setpoint is absolute
new_temp = celcius_to_farhenheit(Float(value_to_assign.to_i)).round
end

# to set the temp, we must know the mode
case $tstathash["tmode"].to_s
when "1"
data = "{\"t_heat\":" + new_temp.to_s + "}"
when "2"
data = "{\"t_cool\":" + new_temp.to_s + "}"
end
log("Set temp data: " + data)
tstat_set(data)

  1. 373 Private method listing:


# Helper function for logging
def log(word)
$logFile.print(word + "\n")
$logFile.flush()
end

def get()

# Reconnect to the device
conn_.Reconnect()

# Send the request
s = "GET /tstat HTTP/1.1\r\n"
s += "\r\n"
conn_.Send(s)

# Wait for a reply
recv = ""
while(true)
buff=conn_.Recv(256, 5000)
if(buff.length() == 0)
break
end
recv = recv + buff
end

# Check that we got a response and try to parse through it
if (recv=~ /^HTTP[^\r\n]+200\sOK.+?\r\n\r\n(.+)$/m)
#parse temp
$tstathash["temp"] = recv.to_s.scan(/\{\"temp\"Sad.*?),/)

#parse tmode
$tstathash["tmode"] = recv.to_s.scan(/\"tmode\"Sad.*?),/)

#parse fmode
$tstathash["fmode"] = recv.to_s.scan(/\"fmode\"Sad.*?),/)

#parse override
$tstathash["override"] = recv.to_s.scan(/\"override\"Sad.*?),/)

#parse hold
$tstathash["hold"] = recv.to_s.scan(/\"hold\"Sad.*?),/)

#parse t_heat
$tstathash["t_heat"] = recv.to_s.scan(/\"t_heat\"Sad.*?),/)

#parse t_cool
$tstathash["t_cool"] = recv.to_s.scan(/\"t_cool\"Sad.*?),/)

#parse time
$tstathash["day"] = recv.to_s.scan(/\"day\"Sad.*?),/)
$tstathash["hour"] = recv.to_s.scan(/\"hour\"Sad.*?),/)
$tstathash["minute"] = recv.to_s.scan(/\"minute\"Sad.*?)\}/)

case $tstathash["tmode"].to_s
when "1"
$tstathash["setpoint"] = recv.to_s.scan(/\"t_heat\"Sad.*?),/)
when "2"
$tstathash["setpoint"] = recv.to_s.scan(/\"t_cool\"Sad.*?),/)
when "3"
$tstathash["setpoint"] = 32.0 #no setpoint for auto ??
else
log("Error getting setpoint! mode:" + $tstathash["tmode"].to_s + " 0 is OFF")
end
end
end

def tstat_set(data, update=true)
# Reconnect to the device

conn_.Reconnect()

s = "POST /tstat HTTP/1.1\r\n"
s += "Content-type: application/x-www-form-urlencoded\r\n"
s += "Content-Length: " + (data.length).to_s() + "\r\n"
s += "\r\n"
s += data
s += "\r\n"

conn_.Send(s)
log("Update: " + data)
# Wait for a reply
recv = ""
while(true)
buff=conn_.Recv(256, 5000)
if(buff.length() == 0)
break
end
recv = recv + buff
end
log(recv.to_s)
# Update the state to reflect the new situation
if (update)
update_state()


end

end

def update_state()
# This function queries the thermostat to get the most recent state

log("Polling thermostat for updates at: " + Time.now.to_s)
get()

# Get the new states
new_tmode = $tstathash["tmode"] # 0-Off, 1-Heat, 2-Cool, 3-Auto
#if ($tstathash["fmode"] == 2)
# Always on
#new_fmode = 2 # On
#else
# Auto/Schedule
#new_fmode = 1 # Auto
#end
new_fmode = $tstathash["fmode"]
new_setpoint = farhenheit_to_celcius(Float($tstathash["setpoint"].to_s))

new_temp = farhenheit_to_celcius(Float($tstathash["temp"].to_s))
#new_time = Time.at(results[4].to_i - Time.now.utc_offset) # Time.at creates a UTC time, wheras the thermostat reports the time in the local time zone

# Update the state and send events when necessary
if (new_tmode != @tmode)
log(" New mode detected : " + new_tmode.to_s)
if (@tmode == 0)
# The old mode was "Off", so now the thermostat is on
cmd = Command.new(device_.devid_, -1001, 1, 2, 28) # On
SendCommand(cmd)
end
if (new_tmode == 0)
# The new mode is "Off", so we send the Off event:
cmd = Command.new(device_.devid_, -1001, 1, 2, 29) # Off
SendCommand(cmd)
else
# We send the Thermostat mode changed event:
cmd = Command.new(device_.devid_, -1001, 1, 2, 78)
cmd.params_[30] = new_tmode.to_s #(new_tmode - 1).to_s
SendCommand(cmd)
end
@tmode = new_tmode
end

if (new_fmode != @fmode)
@fmode = new_fmode
log(" New fan mode detected : " + new_fmode.to_s)
cmd = Command.new(device_.devid_, -1001, 1, 2, 79) # Fan Mode Changed
cmd.params_[30] = new_fmode.to_s # Fan mode value
SendCommand(cmd)
end

if (new_setpoint != @setpoint)
@setpoint = new_setpoint
log(" New temperature setpoint detected : " + new_setpoint.to_s)
cmd = Command.new(device_.devid_, -1001, 1, 2, 27) # Thermostat Set Point Chan
cmd.params_[30] = new_setpoint.to_s # The new set point
SendCommand(cmd)
end

if (new_temp != @temp)
@temp = new_temp
log(" New temperature measurement detected : " + new_temp.to_s)
cmd = Command.new(device_.devid_, -1001, 1, 2, 25) # Temperature changed event
cmd.params_[30] = new_temp.to_s # The ambient temperature
SendCommand(cmd)
end

# Check the latest system time
#@time = new_time
#if ((@time-Time.now).abs > 600)
# Time is out of sync for more than 10 minutes
#log("Thermostat's time ("+@time.to_s+") is out of sync with system time ("+Time.now.to_s+"), resynchronizing")
#data="OID2.5.1=" # Current system time in seconds since Jan 1, 1970
#data+=(Time.now + Time.now.utc_offset).to_i.to_s # Time.to_i returns seconds since epoch in UTC, wheras the thermostat expects the time in seconds since epoch in the local time zone
#pdp_set(data, false)
#end

# Record the last time the state was checked
@last_check = Time.now
end

def farhenheit_to_celcius(cf)
# Converts a temperatue in deci-Farhenheit into deci-degrees Celcius
power = 10.00
return ((((cf - 32.0)*5.0)/9.0) * power).round / power
end

def celcius_to_farhenheit(c)
# Converts a temperatue in degrees Celcius into deci-Farhenheit
power = 10.00
return ((((c*9.0)/5.0)+32.0) * power).round / power
end

  1. 351 process idle:


# Check how long it has been since we queried the thermostat
now = Time.now
if ((@last_check + 300) < now)
# The last check was more than 5 minutes ago
update_state()
end

  1. 350 process incoming data:


conn_.Close()

  1. 355 process init:


# Create Log File
$logFile = File.new("/var/log/pluto/RadioThermostatWiFi.log", "w")
log("Starting RadioThermostatWiFi" + "\n")

@tmode = 0
@fmode = 0
@temp = 0.0
@setpoint = 0.0

# Define Hashes to store our data
$tstathash = Hash.new
$tstathash["hour"] = 0
$tstathash["minute"] = 0
$tstathash["day"] = 0
$tstathash["temp"] = 0.00
$tstathash["setpoint"] = 0.00
$tstathash["tmode"] = 0
$tstathash["fmode"] = 0
$tstathash["override"] = 0
$tstathash["hold"] = 0
$tstathash["t_heat"] = 0.00
$tstathash["t_cool"] = 0.00
$tstathash["tstate"] = 0
$tstathash["fstate"] = 0
$tstathash["t_type_post"] = 0


# Update the state
get()
@tmode = $tstathash["tmode"]
@fmode = $tstathash["fmode"]
@temp = $tstathash["temp"]
@setpoint = $tstathash["setpoint"]
@last_check = Time.now
update_state()

  1. 356 process release:


# Close the Log File
if ($logFile != nil) then
$logFile.close
end
<code>