Difference between revisions of "Message Translation"
From LinuxMCE
| Line 14: | Line 14: | ||
You'll have to set up corectly input sequence for this to work as expected. | You'll have to set up corectly input sequence for this to work as expected. | ||
| − | + | '''List of available inputs''' | |
| − | RGB | + | :RGB, Video 1, Video 2, Video 3, Video 4, Video 5, Tape / Tape 1, TV, CD, Phono, Aux, DVD, Tuner, Video 6, Video 7, AM, FM, DVD Multi, Aux 2, Tape 2, Minidisc, Tuner 2, VDP, Laserdisc, DSS, DVI, Svideo, Composite, RF Input, DBS/Satellite, VCR-1, VCR-2, VCR-3, V.AUX, AV 1, AV 2, AV 3, SVideo/YC 1, SVideo/YC 2, SVideo/YC 3, Tuner 3, WB, SW, HDMI, D4, Input 1, Input 2, Input 3, Input 4, Input 5, Input 6, Input 7, Input 8, Input 9, Input 10, Radio, Antenna, CDR, DAT, External 1, External 2, External 3, Component 1, Component 2, DVR, Composite 2, HDMI 2, RGB 2, PC, HD, AV 4, AV 5, AV 6, AV 7, AV 8 |
| − | Video 1 | + | |
| − | Video 2 | + | |
| − | Video 3 | + | |
| − | Video 4 | + | |
| − | Video 5 | + | |
| − | Tape / Tape 1 | + | |
| − | TV | + | |
| − | CD | + | |
| − | Phono | + | |
| − | Aux | + | |
| − | DVD | + | |
| − | Tuner | + | |
| − | Video 6 | + | |
| − | Video 7 | + | |
| − | AM | + | |
| − | FM | + | |
| − | DVD Multi | + | |
| − | Aux 2 | + | |
| − | Tape 2 | + | |
| − | Minidisc | + | |
| − | Tuner 2 | + | |
| − | VDP | + | |
| − | Laserdisc | + | |
| − | DSS | + | |
| − | DVI | + | |
| − | Svideo | + | |
| − | Composite | + | |
| − | RF Input | + | |
| − | DBS/Satellite | + | |
| − | VCR-1 | + | |
| − | VCR-2 | + | |
| − | VCR-3 | + | |
| − | V.AUX | + | |
| − | AV 1 | + | |
| − | AV 2 | + | |
| − | AV 3 | + | |
| − | SVideo/YC 1 | + | |
| − | SVideo/YC 2 | + | |
| − | SVideo/YC 3 | + | |
| − | Tuner 3 | + | |
| − | WB | + | |
| − | SW | + | |
| − | HDMI | + | |
| − | D4 | + | |
| − | Input 1 | + | |
| − | Input 2 | + | |
| − | Input 3 | + | |
| − | Input 4 | + | |
| − | Input 5 | + | |
| − | Input 6 | + | |
| − | Input 7 | + | |
| − | Input 8 | + | |
| − | Input 9 | + | |
| − | Input 10 | + | |
| − | Radio | + | |
| − | Antenna | + | |
| − | CDR | + | |
| − | DAT | + | |
| − | External 1 | + | |
| − | External 2 | + | |
| − | External 3 | + | |
| − | Component 1 | + | |
| − | Component 2 | + | |
| − | DVR | + | |
| − | Composite 2 | + | |
| − | HDMI 2 | + | |
| − | RGB 2 | + | |
| − | PC | + | |
| − | HD | + | |
| − | AV 4 | + | |
| − | AV 5 | + | |
| − | AV 6 | + | |
| − | AV 7 | + | |
| − | AV 8 | + | |
Revision as of 16:22, 23 May 2006
| This page was written by Pluto and imported with their permission when LinuxMCE branched off in February, 2007. In general any information should apply to LinuxMCE. However, this page should be edited to reflect changes to LinuxMCE and remove old references to Pluto. |
Used to translate between toggle and discrete commands (usually for infrared equipment). When a device only accepts toggle commands and it receives an "ON" or "OFF", it will be translated into "TOGGLE_POWER" depending on device status. Same is true then device accepts discrete commands, but the remote has only toggle button, in this case we will send "ON" or "OFF", again it depends on device state.
Available translations
Power
- ON/OFF to TOGGLE_POWER
- TOGGLE_POWER to ON/OFF
Inputs
- AN INPUT to (one/many) INPUT_SELECT
- INPUT_SELECT to one of the INPUTS
You'll have to set up corectly input sequence for this to work as expected.
List of available inputs
- RGB, Video 1, Video 2, Video 3, Video 4, Video 5, Tape / Tape 1, TV, CD, Phono, Aux, DVD, Tuner, Video 6, Video 7, AM, FM, DVD Multi, Aux 2, Tape 2, Minidisc, Tuner 2, VDP, Laserdisc, DSS, DVI, Svideo, Composite, RF Input, DBS/Satellite, VCR-1, VCR-2, VCR-3, V.AUX, AV 1, AV 2, AV 3, SVideo/YC 1, SVideo/YC 2, SVideo/YC 3, Tuner 3, WB, SW, HDMI, D4, Input 1, Input 2, Input 3, Input 4, Input 5, Input 6, Input 7, Input 8, Input 9, Input 10, Radio, Antenna, CDR, DAT, External 1, External 2, External 3, Component 1, Component 2, DVR, Composite 2, HDMI 2, RGB 2, PC, HD, AV 4, AV 5, AV 6, AV 7, AV 8
