Difference between revisions of "ShuttleX50V2"

From LinuxMCE
Jump to: navigation, search
 
(13 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{versioninfo|810Status=Works, not pnp|810UpdatedDate=8th September 2010|810UpdatedBy=BongoWongo}}
+
{{versioninfo|810Status=Works, not pnp|810UpdatedDate=8th of December 2010|810UpdatedBy=BongoWongo}}
 +
[[Category: Hardware]]
 
[[Category: Media Directors]]
 
[[Category: Media Directors]]
[[Category: Nettops]]
 
[[Category: 0810]]
 
  
 
This page is compliant with 0810 Beta | Current status : '''working, not plug and play'''
 
This page is compliant with 0810 Beta | Current status : '''working, not plug and play'''
  
 
Shuttle X50 V2
 
Shuttle X50 V2
[http://www.shuttle.eu/products/barebones/x50v2/specification/]
+
[http://www.shuttle.eu/products/all-in-one/x50v2/overview/]
  
 
It is a 15,4 inch touchscreen with an atom processor, with builtin camera, microphone and speakers.
 
It is a 15,4 inch touchscreen with an atom processor, with builtin camera, microphone and speakers.
 
Ideal for a kitchen situation.
 
Ideal for a kitchen situation.
 +
 +
Pro's
 +
*Nice esthetics
 +
*All in one
 +
 +
Cons
 +
*Intel GMA is not the best card for LinuxMCE
 +
*Needs configuring
  
 
How to get it working.
 
How to get it working.
  
 
==Diskless Boot==
 
==Diskless Boot==
 +
'''Unrecognized NIC'''
  
#'''Unrecognized NIC'''
+
The driver for the JMicron JMC26X PCI Express Gigabit Ethernet controller needs to be first installed, before the MD will netboot.
The driver for the JMicron JMC250 PCI Express Gigabit Ethernet controller needs to be first installed, before the MD will netboot.
+
Of course adjust the kernel version to your kernel version on the core, and make sure the kernel version of your core and MD are the same if you use chroot.
Download the file jme-1.0.5.tbz2 which contains the driver from
+
ftp://jmicron.com.tw/jmc2xx/Linux/
+
  
 
Open a "terminal" and type the following
 
Open a "terminal" and type the following
  <nowiki>$ tar xjvf jme-1.0.5.tbz2
+
  <nowiki>$ sudo su
$ cd jme-1.0.5
+
$ cd ~
$ make install</nowiki>
+
$ wget ftp://driver.jmicron.com.tw/Ethernet/Linux/jme-1.0.6.1.rar
 
+
$ apt-get install unrar -y
copy the module to the running kernel
+
$ unrar x jme-1.0.6.1.rar
 
+
$ cd jme-1.0.6.1
<nowiki>$ cp jme.ko /lib/modules/2.6.27-17-generic/kernel/drivers/net/</nowiki>
+
$ make install
To get a NIC to work, you have to modify a file, type the following in "terminal"
+
$ cp jme.ko /lib/modules/2.6.27-17-generic/kernel/drivers/net/</nowiki>
  <nowiki>$ sudo <editor-of-choice> /etc/initramfs-tools-interactor/modules</nowiki>
+
Then it is needed to modify the file modules by adding a new line with 'jme'
and add a single line for your NICs kernel module. In the above case the name of the module is
+
  <nowiki>$ sudo <editor-of-choice> /etc/initramfs-tools-interactor/modules
<nowiki>jme</nowiki>
+
$ /usr/pluto/bin/Diskless_BuildDefaultImage.sh</nowiki>
 
+
After adding the above line (and saving the change of course), you have to recreate the initial ramdisk.
+
  
<nowiki>/usr/pluto/bin/Diskless_BuildDefaultImage.sh</nowiki>
+
Boot your MD the first time. After the MD was running the 'Diskless_Setup' and you quick reloaded the router, you have to copy the driver and adding a line with 'jme' into modules for the new created MD.
  
or maybe
+
<nowiki>$ sudo cp /lib/modules/2.6.27-17-generic/kernel/drivers/net/jme.ko /usr/pluto/diskless/<MD#>/lib/modules/2.6.27-17-generic/kernel/drivers/net/jme.ko
 +
$ sudo nano /usr/pluto/diskless/<MD#>/etc/modules
 +
$ sudo nano /usr/pluto/diskless/<MD#>/etc/initramfs-tools/modules</nowiki>
  
<nowiki>mkinitramfs -d /etc/initramfs-tools-interactor/ -o /tftpboot/default/initrd</nowiki>
+
Then in a terminal
  
is enough.
+
<nowiki>$ cd /usr/pluto/diskless/
 +
$ chroot <mediadirector-id>
 +
$ depmod
 +
$ cd /boot
 +
$ mkinitramfs -o initrd.img-`uname -r` `uname -r`
 +
$ exit</nowiki>
  
This will create a new initial ramdisk for the first boot of new MDs containing the jme module. Now, the first boot of the diskless MD will succeed and a new diskless media director will be created.
+
This will create a new initial ramdisk for the first boot of new MDs containing the jme module. Now, the first boot of the diskless MD will succeed and a new diskless media director will be created. After reboot of your MD, the setup-wizzard should appear on screen.
 
#'''ACPI'''
 
#'''ACPI'''
 
Turn it off
 
Turn it off
Line 58: Line 69:
  
 
==Other remarks, needed investigation==
 
==Other remarks, needed investigation==
#Could not get a higher resolution than 640x480, need to configure videocard proper. Driver/Xorg.conf
+
#Could not get a higher resolution than 640x480, need to configure videocard proper. Driver/Xorg.conf possible solution => install intel ppa drivers
 +
sudo apt-get remove -purge nvidia*
 +
http://forum.linuxmce.org/index.php?topic=9149.0
 
#Makes strange dark beep when booting
 
#Makes strange dark beep when booting
 +
#As I do not use it and I was in troubleshooting modus, I disconnected the wifi, so cannot comment on it
 +
#Webcam and microphone are not tested yet
 
This page is a work in progress
 
This page is a work in progress

Latest revision as of 01:20, 28 September 2015

Version Status Date Updated Updated By
710 Unknown N/A N/A
810 Works, not pnp 8th of December 2010 BongoWongo
1004 Unknown N/A N/A
1204 Unknown N/A N/A
1404 Unknown N/A N/A
Usage Information

This page is compliant with 0810 Beta | Current status : working, not plug and play

Shuttle X50 V2 [1]

It is a 15,4 inch touchscreen with an atom processor, with builtin camera, microphone and speakers. Ideal for a kitchen situation.

Pro's

  • Nice esthetics
  • All in one

Cons

  • Intel GMA is not the best card for LinuxMCE
  • Needs configuring

How to get it working.

Diskless Boot

Unrecognized NIC

The driver for the JMicron JMC26X PCI Express Gigabit Ethernet controller needs to be first installed, before the MD will netboot. Of course adjust the kernel version to your kernel version on the core, and make sure the kernel version of your core and MD are the same if you use chroot.

Open a "terminal" and type the following

$ sudo su
$ cd ~
$ wget ftp://driver.jmicron.com.tw/Ethernet/Linux/jme-1.0.6.1.rar
$ apt-get install unrar -y
$ unrar x jme-1.0.6.1.rar
$ cd jme-1.0.6.1
$ make install
$ cp jme.ko /lib/modules/2.6.27-17-generic/kernel/drivers/net/

Then it is needed to modify the file modules by adding a new line with 'jme'

$ sudo <editor-of-choice> /etc/initramfs-tools-interactor/modules
$ /usr/pluto/bin/Diskless_BuildDefaultImage.sh

Boot your MD the first time. After the MD was running the 'Diskless_Setup' and you quick reloaded the router, you have to copy the driver and adding a line with 'jme' into modules for the new created MD.

$ sudo cp /lib/modules/2.6.27-17-generic/kernel/drivers/net/jme.ko /usr/pluto/diskless/<MD#>/lib/modules/2.6.27-17-generic/kernel/drivers/net/jme.ko
$ sudo nano /usr/pluto/diskless/<MD#>/etc/modules
$ sudo nano /usr/pluto/diskless/<MD#>/etc/initramfs-tools/modules

Then in a terminal

$ cd /usr/pluto/diskless/
$ chroot <mediadirector-id>
$ depmod
$ cd /boot
$ mkinitramfs -o initrd.img-`uname -r` `uname -r`
$ exit

This will create a new initial ramdisk for the first boot of new MDs containing the jme module. Now, the first boot of the diskless MD will succeed and a new diskless media director will be created. After reboot of your MD, the setup-wizzard should appear on screen.

  1. ACPI

Turn it off

Needs more info

Touchscreen

Used a keyboard to go through all of the wizards, went into KDE Desktop, installed latest Egalax drivers. Touchscreen works, but has the tendency to double tap. Ignore first event, does not work.

Needs more info

Other remarks, needed investigation

  1. Could not get a higher resolution than 640x480, need to configure videocard proper. Driver/Xorg.conf possible solution => install intel ppa drivers

sudo apt-get remove -purge nvidia* http://forum.linuxmce.org/index.php?topic=9149.0

  1. Makes strange dark beep when booting
  2. As I do not use it and I was in troubleshooting modus, I disconnected the wifi, so cannot comment on it
  3. Webcam and microphone are not tested yet

This page is a work in progress