Difference between revisions of "User:Apagg"

From LinuxMCE
Jump to: navigation, search
 
(9 intermediate revisions by 2 users not shown)
Line 1: Line 1:
== Delayed event ==
+
[[Category:User Setups]]
 +
[[Category:Climate]]
 +
[[Category:Zwave_Setups]]
 +
 
 +
= My Setup =
 +
 
 +
== Home Automation ==
 +
*[[Seluxit viaSENS Home Controller]]
 +
*[[LSControl ES 861]] Temperature sensor
 +
*[[LSControl ES 861 Humidity]] Humidity sensor ''(eats battery's)''
 +
*[[Everspring ST814]] Temp/hum sensor
 +
*[[ACT Homepro ZDW230]] Dimmer wall mounted
 +
*[[Düwi 05433]] Dimmer wall mounted
 +
*[[ACT Homepro ZDP200]] Dimmer plugin
 +
*[[ACT Homepro ZRP200]] Appliance module plugin
 +
*[[Düwi plug adaptor switch ZW ZS 3500]] Appliance module plugin
 +
*[[Merten 507501]] Appliance module Flush-mounted
 +
*[[Express Controls EZmotion]] Temp/Light/Motion sensor
 +
*[[ACT Homepro ZTH200]] Remote
 +
*[[Tricklestar 200ZW-EU-W]] Remote
 +
 
 +
= Delayed event =
  
 
To make a scenario for heating my care in the morning and by a climate scenario on the orbiter I have made the following setup.
 
To make a scenario for heating my care in the morning and by a climate scenario on the orbiter I have made the following setup.
  
  
This scenario turns on the wall outlet for the car and turns it off after 1,5 hours. If I execute this scenario form the orbiter it does not work it will just send all the commands at once and there will be no delay. So I hide this scenario by unchecking all the rooms.  
+
This scenario turns on the wall outlet for the car and turns it off after 1,5 hours. If I execute this scenario form the [[orbiter]] it does not work it will just send all the commands at once and there will be no delay. So I hide this scenario by unchecking all the rooms.  
  
 
[[Image:varm bil (skjult).png|200px|]]
 
[[Image:varm bil (skjult).png|200px|]]
  
I then made another scenario to execute this scenario:
+
I then made another [[scenario]] to execute this scenario:
  
 
[[Image:varm bil.png|200px]]
 
[[Image:varm bil.png|200px]]
  
I also added a timed event to execute this scenario every weekday morning.
+
I also added a [[Timed Events|Timed Event]] to execute this scenario every weekday morning.
  
 
[[Image:varm bil 2.png|200px]]
 
[[Image:varm bil 2.png|200px]]
 +
 +
= Climate control =
 +
I have started my quest to control all heating in my house using LMCE. I am using [[Z-Wave]] as my primary control system. The temp sensors are [[LSControl ES 861]] and the heaters are controlled by various [[Z-Wave]] modules.
 +
 +
The first room out is the bedroom. I only need to have this room warm when I go to bed and wake up. If I am not sleeping at home I don't need to turn the heat up at all ([[Event_criteria#House_Mode|HouseMode]] = Extended-away). These two events control the heater. They are both Temperature Changed [[Events]]. The first event turns the heater on, the second turns it off. <br>
 +
[[Image:Sov on.png|200px]] [[Image:Sov off.png|200px]]

Latest revision as of 14:46, 18 August 2010


My Setup

Home Automation

Delayed event

To make a scenario for heating my care in the morning and by a climate scenario on the orbiter I have made the following setup.


This scenario turns on the wall outlet for the car and turns it off after 1,5 hours. If I execute this scenario form the orbiter it does not work it will just send all the commands at once and there will be no delay. So I hide this scenario by unchecking all the rooms.

Varm bil (skjult).png

I then made another scenario to execute this scenario:

Varm bil.png

I also added a Timed Event to execute this scenario every weekday morning.

Varm bil 2.png

Climate control

I have started my quest to control all heating in my house using LMCE. I am using Z-Wave as my primary control system. The temp sensors are LSControl ES 861 and the heaters are controlled by various Z-Wave modules.

The first room out is the bedroom. I only need to have this room warm when I go to bed and wake up. If I am not sleeping at home I don't need to turn the heat up at all (HouseMode = Extended-away). These two events control the heater. They are both Temperature Changed Events. The first event turns the heater on, the second turns it off.
Sov on.png Sov off.png