Difference between revisions of "Foscam FI8918W"

Revision as of 18:49, 12 April 2011

Thanks

Thank you to the author of the Foscam FI8908W page as this is mostly a copy.

Info

Cheap IR wireless IP/Network Pan/tilt Camera. There is no zoom with this camera.
Very similar camera to the Foscam FI8908W with some modifications to the camera (IR lights) but the firmware (I believe) is the same as the predecessor, the Foscam FI8908W

What's New

Compared to the older Foscam FI8908W:

• IR lights can be turned off with the software (Not in LinuxMCE)
• Audio quality is apparently improved and an added microphone jack is provided. (Not used in LinuxMCE)
• Extra IR light (Eleven now)
• Power and network light at the back of the camera.
• Haven't noticed any drop out isssues on my system

Status

Working as a plug and play IP camera with pan/tilt commands.
Should work as a 'Generic Motion IP camera' under motion wrapper and used as a sensor as well as recording movement etc. - Check the Foscam FI8908W page for more.

Plug and Play Template Settings

This camera is fully plug and play as a stand-alone pan/tilt camera by duplicating the panasonic template and inserting the following scripts.
NOTE: The left and right scripts are the other way around from the what is noted in the Foscam FI8908W

1. 84 Get video frame

conn_.Reconnect()
auth_s="user="+device_.devdata_[114]+"&pwd="+device_.devdata_[115];

fix_path=device_.devdata_[2]+auth_s;
fix_path='/'+fix_path if(fix_path[0]!='/'[0]);

s = "GET "+fix_path+" HTTP/1.0\r\n"
s+= "Accept: */*\r\n"
s+= "\r\n"

conn_.Send(s)
recv=""
while(true)
  buff=conn_.Recv(16384, 5000)
  if(buff.length() == 0)
     break
   end
   recv = recv +  buff
end
if (recv=~ /^HTTP[^\r\n]+200\sOK.+?\r\n\r\n(.+)$/m)
  fileName="/tmp/ip_camera_img"+device_.devid_.to_s
  imageFile=File.new(fileName+".jpg",'w')
  imageFile.print $1
  imageFile.close()
  system("/usr/bin/convert "+fileName+".jpg "+fileName+".png");
  size=File.stat(fileName+".png").size 
  imageFile=File.new(fileName+".png",'r')
  img = imageFile.read(size);
  imageFile.close()
  data_set(img)
  format_set('png')
end

1. 201 Move Down

conn_.Reconnect()
auth_s="user="+device_.devdata_[114]+"&pwd="+device_.devdata_[115];
s = "GET /decoder_control.cgi?command=2&onestep=1&"+auth_s
s+= " HTTP/1.0\r\n Accept: */*\r\n"
s+= "\r\n"

conn_.Send(s)
recv=""
while(true)
  buff=conn_.Recv(256, 5000)
  if(buff.length() == 0)
     break
   end
   recv = recv +  buff
end

1. 202 move left

conn_.Reconnect()
auth_s="user="+device_.devdata_[114]+"&pwd="+device_.devdata_[115];
#auth_a=Array.new;
#auth_s.each{|c| auth_a.push(c)}
s = "GET /decoder_control.cgi?command=6&onestep=1&"+auth_s
s+= " HTTP/1.0\r\n Accept: */*\r\n"
#s+= "Authorization: Basic "+auth_a.pack("m").chop+"\r\n"
s+= "\r\n"

conn_.Send(s)
recv=""
while(true)
  buff=conn_.Recv(256, 5000)
  if(buff.length() == 0)
     break
   end
   recv = recv +  buff
end

1. 203 Move Right

conn_.Reconnect()
auth_s="user="+device_.devdata_[114]+"&pwd="+device_.devdata_[115];
#auth_a=Array.new;
#auth_s.each{|c| auth_a.push(c)}
s = "GET /decoder_control.cgi?command=4&onestep=1&"+auth_s
s+= " HTTP/1.0\r\n Accept: */*\r\n"
#s+= "Authorization: Basic "+auth_a.pack("m").chop+"\r\n"
s+= "\r\n"

conn_.Send(s)
recv=""
while(true)
  buff=conn_.Recv(256, 5000)
  if(buff.length() == 0)
     break
   end
   recv = recv +  buff
end

1. 200 Move Up

conn_.Reconnect()
auth_s="user="+device_.devdata_[114]+"&pwd="+device_.devdata_[115];
#auth_a=Array.new;
#auth_s.each{|c| auth_a.push(c)}
s = "GET /decoder_control.cgi?command=0&onestep=1&"+auth_s
s+= " HTTP/1.0\r\n Accept: */*\r\n"
#s+= "Authorization: Basic "+auth_a.pack("m").chop+"\r\n"
s+= "\r\n"

conn_.Send(s)
recv=""
while(true)
  buff=conn_.Recv(256, 5000)
  if(buff.length() == 0)
     break
   end
   recv = recv +  buff
end

It can be made 'plug and play' by adding the mac range of both the wireless and wired adapters into the new template:

• Wireless range 963357310976 to 963357376511 (DHCP).
• Wired range ??????? - Will try and find this out???????

Pros:

• Plug and play (Just give it a sensible name)
• Pan and Tilt work from on screen arrows

Cons:

• No motion capture

Features

• Browser based
• 10/100mbit LAN
• WPA2 wireless security

Dropouts

There have been reported drop outs with the Foscam F8908W but I have not noticed this with the Foscam F8918W but I do use a static IP address.

Links

http://www.foscam.com