Difference between revisions of "WebDT 366 WPA2"
| (2 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
[[Image:Edup.JPG|right|thumb|290px]] | [[Image:Edup.JPG|right|thumb|290px]] | ||
| + | [[Image:Wpa2webdt.JPG|Wpa2webdt.JPG]] | ||
| Line 24: | Line 25: | ||
<br> | <br> | ||
Boot and install the Pad Orbiter software. | Boot and install the Pad Orbiter software. | ||
| + | <br> | ||
| + | When you get to the wireless setup just hit cancel and open up a terminal: CTRL + T then C | ||
| + | <br> | ||
| + | <pre> | ||
| + | lspci | ||
| + | </pre> | ||
| + | Should show that the RT2500 module is loaded. | ||
| + | <br> | ||
| + | Then we have to edit the network interfaces file to allow for WPA2 and SSID details. My preferred editor is nano but choose your own. | ||
| + | <br> | ||
| + | <pre> | ||
| + | nano /etc/network/interfaces | ||
| + | </pre> | ||
| + | Then edit the network interfaces file, delete the eth0 lines and change to show: | ||
| + | <pre> | ||
| + | allow-hotplug wlan0 | ||
| + | iface wlan0 inet dhcp | ||
| + | wpa-driver wext | ||
| + | wpa-ssid <your_essid> | ||
| + | wpa-ap-scan 1 | ||
| + | wpa-proto RSN | ||
| + | wpa-pairwise CCMP | ||
| + | wpa-group CCMP | ||
| + | wpa-key-mgmt WPA-PSK | ||
| + | wpa-psk <your_hex_key> | ||
| + | </pre> | ||
| + | wpa-ap-scan: 1 = broadcast of essid, 2 = hidden essid | ||
| + | <br> | ||
| + | wpa-proto: RSN = WPA2, WPA = WPA | ||
| + | <br> | ||
| + | wpa-pairwise and wpa-group: CCMP = AES, TKIP = TKIP | ||
| + | <br> | ||
| + | wpa-key-mgmt: WPA-PSK = Authentication via pre-shared key | ||
| + | <br> | ||
| + | wpa-psk: <see below for hex key generation> | ||
| + | <br> | ||
| + | In a terminal type | ||
| + | <pre> | ||
| + | wpa_passphrase <your_essid> <password> | ||
| + | </pre> | ||
| + | and you should get an output after the psk= line and that is what you need to input. | ||
| + | <br> | ||
| + | Save and exit and then start up wlan0 | ||
| + | <pre> | ||
| + | ifup wlan0 | ||
| + | </pre> | ||
| + | After that the Pad Orbiter should continue loading. | ||
Latest revision as of 22:48, 3 April 2011
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | Unknown | N/A | N/A |
| 810 | Unknown | N/A | N/A |
| 1004 | Unknown | N/A | N/A |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
Info
How to get WPA2 wireless on the WebDT 366
NOTE: At this stage suspend does not work as the driver doesn't support restart from suspend so won't connect to the core. A patch to the kernel should be possible but is both beyond my capabilities and my WebDT's stay on all the time.
Hardware
You will need a PCMCIA wireless card
I purchased an EDUP wireless PCMCIA card which runs the Ralink RT2500 driver which is supported out of the box with the Pad Orbiter software
There are other branded RT2500 cards out there I believe but this one is pretty cheap on ebay.
Installation
Remove the Cisco card and put the EDUP card in.
Boot and install the Pad Orbiter software.
When you get to the wireless setup just hit cancel and open up a terminal: CTRL + T then C
lspci
Should show that the RT2500 module is loaded.
Then we have to edit the network interfaces file to allow for WPA2 and SSID details. My preferred editor is nano but choose your own.
nano /etc/network/interfaces
Then edit the network interfaces file, delete the eth0 lines and change to show:
allow-hotplug wlan0 iface wlan0 inet dhcp wpa-driver wext wpa-ssid <your_essid> wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk <your_hex_key>
wpa-ap-scan: 1 = broadcast of essid, 2 = hidden essid
wpa-proto: RSN = WPA2, WPA = WPA
wpa-pairwise and wpa-group: CCMP = AES, TKIP = TKIP
wpa-key-mgmt: WPA-PSK = Authentication via pre-shared key
wpa-psk: <see below for hex key generation>
In a terminal type
wpa_passphrase <your_essid> <password>
and you should get an output after the psk= line and that is what you need to input.
Save and exit and then start up wlan0
ifup wlan0
After that the Pad Orbiter should continue loading.
