Difference between revisions of "EasyN FS-603A-M106 IP Camera"
From LinuxMCE
(→Setup) |
(→Setup) |
||
| (7 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
[[Category: Hardware]] | [[Category: Hardware]] | ||
| − | {{Versioninfo|810Status=Working|810UpdatedDate=30 April 2011|810UpdatedBy=Jamo}} | + | {{Versioninfo|810Status=Working|810UpdatedDate=30 April 2011|810UpdatedBy=Jamo|1004Status=Working|1004UpdatedDate=2012-08-27|1004UpdatedBy=Jamo}} |
[[Category: Cameras]] | [[Category: Cameras]] | ||
[[Category: IP Cameras]] | [[Category: IP Cameras]] | ||
| − | |||
| − | |||
= Status = | = Status = | ||
| − | The EasyN FS-603 works with video. | + | <br> |
| + | [[Image:RMI-550wf IPCAMERA_thumb.jpg|link=RMI-550wf IPCAMERA.jpg]] | ||
| + | |||
| + | |||
| + | * The EasyN FS-603 works with video via wired network | ||
| + | * Could not get FS-603 to connect to my WPA-2 wi-fi access point. Not sure why - did not try with a non-protected accesspoint. | ||
= Features = | = Features = | ||
* Browser based | * Browser based | ||
* 10/100mbit LAN | * 10/100mbit LAN | ||
| + | * Wi-fi | ||
| + | * IR - day/night | ||
* 30fps max | * 30fps max | ||
* Supports high speed hardware-based Motion-JPEG compression | * Supports high speed hardware-based Motion-JPEG compression | ||
| Line 29: | Line 34: | ||
=Setup= | =Setup= | ||
| − | * Video stream URL: http://cameraIP:webserverport/videostream.cgi | + | * Video stream URL: <nowiki>http://cameraIP:webserverport/videostream.cgi</nowiki> |
| − | * Followed IP Cameras wiki and it worked flawlessly | + | * Followed [[IP_Cameras|IP Cameras wiki]] and it worked flawlessly |
=Comment= | =Comment= | ||
| Line 37: | Line 42: | ||
* Support / manual is horrendous - translation from mandarin or something and no website/forum/tech-support evident | * Support / manual is horrendous - translation from mandarin or something and no website/forum/tech-support evident | ||
* web-based setup works OK but lots of features that are probably intended for other models not supported by this one (switch on/off, zoom etc) | * web-based setup works OK but lots of features that are probably intended for other models not supported by this one (switch on/off, zoom etc) | ||
| + | * On maunfacturer website (http://www.easynp.com) it appears product is old / discontinued | ||
| + | * Purchase source: http://www.securitycameras.co.za/shop/product_info.php?cPath=32&products_id=253 | ||
Latest revision as of 17:47, 7 October 2012
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | Unknown | N/A | N/A |
| 810 | Working | 30 April 2011 | Jamo |
| 1004 | Working | 2012-08-27 | Jamo |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
Contents
Status
- The EasyN FS-603 works with video via wired network
- Could not get FS-603 to connect to my WPA-2 wi-fi access point. Not sure why - did not try with a non-protected accesspoint.
Features
- Browser based
- 10/100mbit LAN
- Wi-fi
- IR - day/night
- 30fps max
- Supports high speed hardware-based Motion-JPEG compression
- Supports video resoultion:640x480(VGA),320x240(CIF) and 160x120(QCIF)
- UPnP, DynDNS
- Real-Time Live Video
Installation notes
- technical issue - the camera has a thick cable that comes out of the back plate which then splits into various connectors - s-video, RCA, A reset switch, 12v supply socket and RJ-45 female port. I installed the camera on an external wall of the house and drilled a hole through the double-skin brick wall in order to push the cable through neatly.... problem was the cable (specifically because of the RJ-45 jack) would require a HUGE diameter hole to go through... probably around 40mm. That is a big hole to put in the wall of your house in order to neatly install a camera. I experimented with a number of options but ended up cutting the cable *gasp* and re-soldering and heat-shrinking the individual copper wires on the inside of the wall. Not a great solution but it was done neatly and it works.
- 12v power supply: the camera comes with a transformer to take 230v AC down to the 12V DC supply required by the camera. I had to install a 230V AC wall socket in my ceiling area in order to plug in the transformer.
- Wall bracket supplied is not particularly solid, nor or the wall plugs and screws to mount it. Be gentle and careful... it's easier to over-tighten and strip. So far it is still pointing in the right direction despite a few large storms.
EasyN FS-603 Camera and Motion Wrapper
IP cameras can be used under the Motion Wrapper to enable it to detect motion and alert based on that function. I haven't tested or experimented with this feature yet.
Setup
- Video stream URL: http://cameraIP:webserverport/videostream.cgi
- Followed IP Cameras wiki and it worked flawlessly
Comment
- Good for the price- about ZAR1600 delivered. Very cheap for IP camera
- Support / manual is horrendous - translation from mandarin or something and no website/forum/tech-support evident
- web-based setup works OK but lots of features that are probably intended for other models not supported by this one (switch on/off, zoom etc)
- On maunfacturer website (http://www.easynp.com) it appears product is old / discontinued
- Purchase source: http://www.securitycameras.co.za/shop/product_info.php?cPath=32&products_id=253
