Difference between revisions of "ACT Homepro ZDW232"
From LinuxMCE
(→Advanced Features) |
|||
| Line 15: | Line 15: | ||
Here is how to '''[[Tweak advanced ZWave settings]]''' | Here is how to '''[[Tweak advanced ZWave settings]]''' | ||
| − | * Night Light | + | * '''Night Light''' |
** Parameter No: 3 | ** Parameter No: 3 | ||
** Length: 1 Byte | ** Length: 1 Byte | ||
| Line 21: | Line 21: | ||
** The LED on the ZDW232 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1. | ** The LED on the ZDW232 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1. | ||
| − | * Invert Switch | + | * '''Invert Switch''' |
** Parameter No: 4 | ** Parameter No: 4 | ||
** Length: 1 Byte | ** Length: 1 Byte | ||
| Line 27: | Line 27: | ||
** To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1. | ** To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1. | ||
| − | * Adjusting Dim Rate | + | * '''Set Ignore Start Level Bit When Transmitting Dim Commands''' |
| − | + | * '''Suspend Group 4''' | |
| + | * '''Disable Group 4 During a Dim Command''' | ||
| + | * '''Ignore Start Level When Receiving Dim Commands''' | ||
| + | * '''Don’t Send Level Command After Transmitting Dim Commands''' | ||
| + | * '''Adjusting Dim Rate''' | ||
| + | * '''On/Off Command dim rate (excluding ALL ON/ALL OFF commands)''' | ||
| + | * '''Enable Shade Control Group 2''' | ||
| + | * '''Enable Shade Control Group 3''' | ||
| + | * '''LED Transmission Indication''' | ||
= Caveats = | = Caveats = | ||
Revision as of 20:00, 28 June 2010
| Version | Status | Date Updated | Updated By |
|---|---|---|---|
| 710 | According to category, Works without caveats | 27th Jun 2010 | Valent |
| 810 | According to category, Works without caveats | 11th May 2010 | Valent |
| 1004 | Unknown | N/A | N/A |
| 1204 | Unknown | N/A | N/A |
| 1404 | Unknown | N/A | N/A |
| Usage Information | |||
Contents
Features
- The ZDW232 is a single dimming receiver which controls the connected load ON/OFF and DIM/BRIGHT and also serves as a transmitter using multiple switch taps (controls one group of 5 Z-Wave modules).
- ZDW232 replaces an existing wall switch.
- ZDW232 can be programmed as a routing slave to establish firm signal routes and can be "associated" with other Z-wave devices in order to control them.
- ZDW232 can be configured to Control Shades or Window Coverings via Z-Wave network.
Advanced Features
Here is how to Tweak advanced ZWave settings
- Night Light
- Parameter No: 3
- Length: 1 Byte
- Valid Values = 0 or 1 (default value is 0)
- The LED on the ZDW232 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1.
- Invert Switch
- Parameter No: 4
- Length: 1 Byte
- Valid Values = 0 or 1 (default value is 0)
- To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1.
- Set Ignore Start Level Bit When Transmitting Dim Commands
- Suspend Group 4
- Disable Group 4 During a Dim Command
- Ignore Start Level When Receiving Dim Commands
- Don’t Send Level Command After Transmitting Dim Commands
- Adjusting Dim Rate
- On/Off Command dim rate (excluding ALL ON/ALL OFF commands)
- Enable Shade Control Group 2
- Enable Shade Control Group 3
- LED Transmission Indication
Caveats
Do not connect regulat CFL bulbs to this switch because if they aren't special dimmable CFL bulbs.
About
This is the 2-wire version, there is also a 3-wire version (ZDW230) available.
