Difference between revisions of "Hauppauge WinTV-PVR-USB2"
From LinuxMCE
Rwilson131 (Talk | contribs) |
Rwilson131 (Talk | contribs) |
||
| Line 3: | Line 3: | ||
* Manufacturer info: http://www.hauppauge.com/pages/products/data_pvrusb2.html | * Manufacturer info: http://www.hauppauge.com/pages/products/data_pvrusb2.html | ||
* This device is compatible with LinuxMCE | * This device is compatible with LinuxMCE | ||
| − | |||
| − | |||
| − | |||
| − | |||
**Under Mythtv-setup you will need to select a new capture card and select the PVR150 option | **Under Mythtv-setup you will need to select a new capture card and select the PVR150 option | ||
| Line 26: | Line 22: | ||
* DVD or CD-RW writer (optional for burning DVDs or Video CD’s) | * DVD or CD-RW writer (optional for burning DVDs or Video CD’s) | ||
* VGA card (PCI or AGP) which supports video overlay (NVidia, S3, ATI, etc.) | * VGA card (PCI or AGP) which supports video overlay (NVidia, S3, ATI, etc.) | ||
| + | |||
| + | ===Troubleshooting=== | ||
| + | # Currently the ivtv-firmware packages are not being installed by default along with the other ivtv packages, which means that the card is not initialized properly. The fix is simple: Alt-Ctrl-2 into a session and issue the following commands: | ||
| + | apt-get install ivtv-firmware | ||
| + | rmmod ivtv | ||
| + | modprobe ivtv | ||
| + | This should give you a working card | ||
[[Category:Hardware]] | [[Category:Hardware]] | ||
[[Category:Video]] | [[Category:Video]] | ||
Revision as of 01:44, 10 September 2007
Functionally, the "PVR USB2" device is very similar to Hauppauge's line of "PVR-XXX" PCI based tuner cards - except this device uses USB instead of PCI which makes it suitable for laptop, xbox, or embedded device applications where there would otherwise not be a PCI slot available.
- Manufacturer info: http://www.hauppauge.com/pages/products/data_pvrusb2.html
- This device is compatible with LinuxMCE
- Under Mythtv-setup you will need to select a new capture card and select the PVR150 option
WinTV-PVR-USB2 includes:
- 125 channel cable ready TV tuner for TV in a window (or full screen). Surf the net while you watch TV on your PC screen!
- No need to open your PC: works best with USB 2.0. Will also work with USB 1.1.
- Composite/S-Video and audio inputs to connect to VCR, camcorders or satellite receivers.
- Built-in hardware MPEG-2 encoder.
- Record TV or videos to disk using from 1-2 Gigabytes of disk space per hour of recorded video. While recording, the WinTV-PVRs' hardware MPEG encoder does all the work, so your PC continues to run at full speed.
- Over USB 2.0, the WInTV-PVR-USB2 can record at up to 12MBits/sec. On USB 1.1, recording is limited to 6MBits/ec.
The WinTV-PVR-USB2's TV tuner and S-Video/composite video inputs are for either PAL or NTSC.
System Requirements:
- Pentium® III processor 733MHz or faster, 128MB RAM and 10GB disk drive minimum recommended
- Available USB 2.0 or 1.1 port (works faster on USB 2.0)
- Sound card
- DVD or CD-RW writer (optional for burning DVDs or Video CD’s)
- VGA card (PCI or AGP) which supports video overlay (NVidia, S3, ATI, etc.)
Troubleshooting
- Currently the ivtv-firmware packages are not being installed by default along with the other ivtv packages, which means that the card is not initialized properly. The fix is simple: Alt-Ctrl-2 into a session and issue the following commands:
apt-get install ivtv-firmware rmmod ivtv modprobe ivtv
This should give you a working card
