Difference between revisions of "User:Apagg"
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Category:User Setups]] | ||
| + | [[Category:Climate]] | ||
| + | [[Category:Zwave_Setups]] | ||
| + | |||
= My Setup = | = My Setup = | ||
| Line 6: | Line 10: | ||
*[[LSControl ES 861 Humidity]] Humidity sensor ''(eats battery's)'' | *[[LSControl ES 861 Humidity]] Humidity sensor ''(eats battery's)'' | ||
*[[Everspring ST814]] Temp/hum sensor | *[[Everspring ST814]] Temp/hum sensor | ||
| − | *[[ACT Homepro ZDW230]] Dimmer wall | + | *[[ACT Homepro ZDW230]] Dimmer wall mounted |
| + | *[[Düwi 05433]] Dimmer wall mounted | ||
*[[ACT Homepro ZDP200]] Dimmer plugin | *[[ACT Homepro ZDP200]] Dimmer plugin | ||
*[[ACT Homepro ZRP200]] Appliance module plugin | *[[ACT Homepro ZRP200]] Appliance module plugin | ||
| + | *[[Düwi plug adaptor switch ZW ZS 3500]] Appliance module plugin | ||
*[[Merten 507501]] Appliance module Flush-mounted | *[[Merten 507501]] Appliance module Flush-mounted | ||
*[[Express Controls EZmotion]] Temp/Light/Motion sensor | *[[Express Controls EZmotion]] Temp/Light/Motion sensor | ||
*[[ACT Homepro ZTH200]] Remote | *[[ACT Homepro ZTH200]] Remote | ||
| + | *[[Tricklestar 200ZW-EU-W]] Remote | ||
= Delayed event = | = Delayed event = | ||
Latest revision as of 14:46, 18 August 2010
My Setup
Home Automation
- Seluxit viaSENS Home Controller
- LSControl ES 861 Temperature sensor
- LSControl ES 861 Humidity Humidity sensor (eats battery's)
- Everspring ST814 Temp/hum sensor
- ACT Homepro ZDW230 Dimmer wall mounted
- Düwi 05433 Dimmer wall mounted
- ACT Homepro ZDP200 Dimmer plugin
- ACT Homepro ZRP200 Appliance module plugin
- Düwi plug adaptor switch ZW ZS 3500 Appliance module plugin
- Merten 507501 Appliance module Flush-mounted
- Express Controls EZmotion Temp/Light/Motion sensor
- ACT Homepro ZTH200 Remote
- Tricklestar 200ZW-EU-W Remote
Delayed event
To make a scenario for heating my care in the morning and by a climate scenario on the orbiter I have made the following setup.
This scenario turns on the wall outlet for the car and turns it off after 1,5 hours. If I execute this scenario form the orbiter it does not work it will just send all the commands at once and there will be no delay. So I hide this scenario by unchecking all the rooms.
.png)
I then made another scenario to execute this scenario:
I also added a Timed Event to execute this scenario every weekday morning.
Climate control
I have started my quest to control all heating in my house using LMCE. I am using Z-Wave as my primary control system. The temp sensors are LSControl ES 861 and the heaters are controlled by various Z-Wave modules.
The first room out is the bedroom. I only need to have this room warm when I go to bed and wake up. If I am not sleeping at home I don't need to turn the heat up at all (HouseMode = Extended-away). These two events control the heater. They are both Temperature Changed Events. The first event turns the heater on, the second turns it off.
